PEAKnx PNX12-10001 Touch Panel Controlmini User Manual
- June 9, 2024
- PEAKnx
Table of Contents
PNX12-10001 Touch Panel Controlmini
User Manual
Controlmini and Gira DCS
Getting started
Created for use with the following product | Item number |
---|---|
Controlmini | PNX12-10001 |
Introduction
The following instructions explain how to set up a Gira door station with your
PEAKnx touch panel.
Audioassistant of the TKS Communicator
-
Select audio components
− Select the „Microphone and Loudspeaker“ option.
-
Adjusting the volume
− Start the volume test and adjust the slider to your needs. By default a position in the middle is recommended.
-
Select recording device
− Select the option „Microphone (Intel SST Audio Device(WDM))“ here.
-
Adjusting the microphone volume
− Do the speech test and move the slider to the second line from the right.
− Select „Settings“ at the bottom of the window.
− In the next window double-click on the microphone with the green tick.
− Here you can now set the gain under the „Level“ tab.
− Adjust the microphone volume (Microphone) to the middle.
− Set the microphone boost to +12.0 dB.
− Accept the settings and close the window to continue with the wizard.
■ Calibrate microphone volume
− Press the „Start“ button and adjust the slider to the middle.
■ Optimize voice quality
− Perform the voice quality test. -
Optimize microphone volume
− Move the slider to the second line from the right.
-
Test configuration
− Start the configuration test. -
Finish Audio Assistant
− Close the audio assistant and have fun with your Controlmini intercom!
Troubleshooting
Problem | Solution |
---|
After a few seconds of good intelligibility on the door unit, the person on
the PEAKnx Panel is suddenly perceived quiet and barely audible or cut off and
hard to hear.| Microphone is amplified too much, see point 4 Microphone
volume. Reduce microphone volume slightly or reduce microphone level slightly
(slider to the left)
At the door unit, the person at the PEAKnx Panel is perceived at the correct
volume but with white noise in the background.| The wizard amplifies the
microphone of the PEAKnx Panel too much, see point 5
Optimize microphone volume. Reduce the microphone volume (slider to the left)
At the door unit, the person at the PEAKnx Panel is perceived too quiet.| The
microphone is not amplified enough, see point 4 Microphone volume. Increase
the microphone volume (slider to the right)
Display TKS Communicator larger
■ Right-click on the TKS Communicator shortcut and select Properties.
■ Switch to the Compatibility tab.
■ Click on Change high DPI settings.
■ Check Override high DPI scaling behavior and select “System (Advanced)” from
the dropdown menu below it.
■ Confirm with “Ok” in both windows.
When the bell is pressed, switch on the screen via the Gira Home Server
■ Create TKS IP gateway:
■ Create internal KOs (communication objects):
■ IP/EIB telegrams (send):
Receiver (Empfänger): IP/Host-Address: IP address of the panel
Send (Senden): Text (Text): TecTool command. To learn more about TecTool, click here.
■ Create logic:
Technical Support
If you experience problems with your PEAKnx Panel please contact our PEAKnx
Support Team:
− Mail: support@peaknx.com
− Create a Support Ticket:
support.peaknx.com/?lang=en_US
− Tel.: +49-6151-279 1825
The product names mentioned in this document may be brands or registered trademarks of their respective owners. These are not explicitly labeled with “™” or “®”.
© PEAKnx GmbH
Otto-Röhm-Strasse 69
64293 Darmstadt
Germany
www.peaknx.com
info@peaknx.com
Document version: 2.1.0
Date: 17.05.22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>