pTron Soundster Pixel Over Ear Headphones User Guide

: August 23, 2024
: pTron

Table of Contents

pron Soundster Pixel Over-Ear Headphones
TO CHARGE THE CHARGING CASE
Pairing with Devices
Basic Operation
Troubleshooting
Packing Box Content
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

pron Soundster Pixel Over-Ear Headphones

Important: pTron ‘Soundster Pixel’ is set at 50% default volume. You can increase the volume through the headset or the connected device.

TO CHARGE THE CHARGING CASE

Connect the type-C charging cable to the headset’s charging port.
Connect the other end of the cable to a USB power source (e.g., computer, wall adapter).
The LED indicator will show a charging status ( red while charging and blue when fully charged).

POWER ON/OFF
Press and hold the power button for a few seconds to turn the headset on or off.

Pairing with Devices

Turn on the headset, the headset will automatically go to Bluetooth mode, and the LED indicator red & blue flash rapidly.
Turn on the Bluetooth on your device, and search ” PTron BT”
Tap “pTron BT” to connect. Headset will respond with a voice prompt: ” Connected.”
When the Bluetooth signal is lost, the headset will respond with a voice prompt “DISCONNECTED” and will shut down automatically after 5 minutes.
When the headset is powered on, the headset will connect to the last paired device automatically. If not, please repeat the above steps.

Basic Operation

Power on/off: Turn on/off the headset by pressing the power button.
Volume control: Press one time “+” button to increase the sound and Press one time ” to decrease the sound.
Play/Pause: Press the power button once to start or pause audio playback.
Next/Previous track: Long press the “+” & “buttons to move to the next & previous track when playing music.
Mode Button: Press the Power button to change the headset mode to Game Mode, Movie Mode, and Music.

Call Control

To Answer A Call: Press the MFB button once.
To End A Call: Press the MFB button once.
To Reject A Call: Long press(2 to 3 sec) the MFB button
To Redial A Call: Press the MFB button twice.

Voice Assistant
Long press the MFB button to activate the default smart voice assistant. The respective voice assistant screen pops up on the connected and you may place your command.

Wired Connection(3.5mm Aux):

To use a wired connection, connect one end of the 3.5mm audio cable to the headset AUX IN port
Connect the other end of the audio cable to the headphone jack of your audio source (phone, tablet, computer, etc.).

Troubleshooting

Scenario 1: Connectivity Issue

Turn OFF the Headset and charge 100%.
Unpaired with the connected Bluetooth device.
Restart the bluetooth device.
After 100% charging switch ON the Headset and pair it with the bluetooth device again.

Scenario 2: Headset Disconnecting During a Phone Call

The headset must be 100% charged before use (a low battery can also cause call drops).
Unpair the Headset with your connected device and restart the device.
Pair the Headset again.

Important: Please use this Headset within a 10-meter wireless range from the connected device.

Safety Precautions

Keep the device out of extreme heat and humidity.
Play time may vary depending on personal habits,
Using incompatible USB cables or high-voltage chargers can damage the product & void the product warranty.
We strongly recommend using good quality DC5V-1A chargers & the USB cable included in the package.
Please don’t over-charge the product as it will decrease the service life of the battery.
Read all warnings on the product and in the operating instructions.
It is recommended to utilize the product below the maximum volume to protect hearing and extend headset service life.
Please don’t open/temper the product or the product’s battery.
Please keep the product out of children’s reach.
Stop using this product immediately if it causes discomfort or pain.
Dispose of the product responsibly and adhere to your local authority guidelines.

Packing Box Content

1 Headset
1 USB Type-C charging cable
1 Aux cable & 1
User Manual/Warranty QR Card

What is Covered in Warranty?
Manufacturing defects in materials and workmanship of the product ONLY. This warranty applies when the product is used under normal conditions and for the purpose for which the product was designed. No warranty on product accessories such as aux cables, and small charging USB cables. To avail warranty, Product Registration is Mandatory at https://ptron.in/apps/product-registration Please read through the complete warranty details at https://ptron.in/pages /repair-service-warranty

Customer Care Details
Mail: support@ptron.in
Tel: 040 – 67138888
Service Centers List: https://ptron.in/pages/ptron-service-centers

Disclaimer
The color and specifications shown in or mentioned in the user manual may differ from the actual product. Images shown are for representation purposes only. Other product logos and company names mentioned herein may be trademarks or trade names of their respective owners.