SOLIGHT 1L75B Wireless Doorbell Owner’s Manual

SOLIGHT 1L75B Wireless Doorbell

Product Usage Instructions

LED Indicator

• The LED indicator serves as a visual cue for various functions of the doorbell.

Melody Selection / Pairing

• To select a melody or pair the doorbell with the transmitter, use the designated button for this function.

Change the Volume

• Adjust the volume of the doorbell by following the instructions provided in the user manual.

Button Description

• Understand the functions of each button on the doorbell for easy operation.

Ring Button

• This button is used to activate the doorbell and produce the selected ringtone.

Delete Button

• The delete button allows you to remove or reset certain settings on the doorbell.

Place for Name Badge

• You can personalize your doorbell by adding a name badge to the designated area.

Base

• The base provides stability and support for the doorbell unit.

FAQ

• Q: How do I change the ringtone on the doorbell?
• A: To change the ringtone, press the Melody Selection button and follow the instructions to cycle through the available options.
• Q: What should I do if the doorbell range seems limited?
• A: Ensure that no obstacles are blocking the signal path between the transmitter and the doorbell. You may also try repositioning either unit for better signal reception.
• Q: Can I use rechargeable batteries with this doorbell?
• A: It is recommended to use standard AA (LR06) batteries as specified in the manual for optimal performance.

Introduction

The set consists of a bell button (transmitter) and a bell (receiver). The bell is designed to be battery-powered. The transmission between the button and the bell is via radio waves with a frequency of 433,92 MHz. The range depends on local conditions and can reach up to 180 m in open areas without interference. The set has the so-called pairing function (Learning code ) – The button can generate its pairing code, which is received by the doorbell and stored in its memory. The set can thus be expanded with additional transmitters or receivers. The pairing function also prevents the set from affecting neighboring doorbells. For proper use, read the instruction manual.

Description of the doorbell

• 1. LED indicator
• 2. Melody selection / Pairing
• 3. Change the volume

Button description

• 4. Ring button
• 5. Delete button
• 6. Place for name badge
• 7. Base

Specifications

Solight 1L74T can be used as a replacement button.

Pairing the button with the bell

1. Connect 2x AA batteries to the doorbell.
2. Wait for the melody “Ding Dong”, when it sounds the device enters pairing mode.
3. You now have 120 seconds to press the button on the transmitter to complete the pairing. When pairing is successful, the “Ding Dong” melody will be heard. If it does not sound, repeat the pairing process.

To pair multiple buttons, repeat steps 1, 2, 3 again for each button. A maximum of 8 buttons can be paired to one doorbell. One button can be paired with up to 15 bells.

Note: The doorbell has an internal memory where it stores the codes of the currently paired transmitters in case of power failure. Therefore, there is no need to pair the transmitter again after an outage. After a power failure, the selected melody will be retained, but the volume must be set again. The receiver is intended for indoor use only.

To delete paired buttons from memory

1. Press and hold the melody selection button 2 (approx. 20 seconds) until you hear the “Ding Dong” sound.
2. This clears the pairing.
3. If the above procedure does not work, open the transmitter and press button 5.

To select a ringtone and volume

1. Press button 2 on the doorbell to select the ringtone.
2. Press the 3 buttons to select the desired volume.

Button location

1. Start by pairing the button with the doorbell.
2. Before installation, test the range and reliability of the device in the chosen location. The button is weatherproof. Even so, preferably choose a location where the button is protected, e.g. in a recess in the wall.
3. Attach the installation pad to the surface using double-sided tape or screw it in. (If screwed in, use dowels.)
4. Place the button on the attached rear part.

Note: Do not place the button directly on metal objects or materials containing metal, such as steel posts or metal-framed doors. In such cases, the device may not operate properly.

Troubleshooting

• If the receiver does not ring repeatedly after pressing the button on the transmitter, check:
• the distance between the transmitter and receiver is not too great
• whether there are strong sources of signal interference between the transmitter and receiver (radio and wireless networks, large metal objects, reinforced concrete walls, etc.)

Replacing the transmitter battery

1. Open the transmitter cover with a flathead screwdriver.
2. Insert the CR2032 battery carefully (the location shown on the plate inside the device).
3. Reattach the cover.

Replacing the receiver battery

1. Open the back cover of the receiver.
2. Insert 2x AA batteries.
3. Close the back cover.

If you have any problems, please contact your dealer. The product is covered by a CE Declaration of Conformity under the applicable regulations.
On the website or on request from the manufacturer: info@solight.cz
Solight Holding s.r.o. declares that the product complies with the requirements and provisions of Directive 2014/53/EU.
The equipment can be operated freely in the EU. The Declaration of Conformity is available at www.solight.cz. The product can be operated under general authorization No.VO-R/10/05.2014-3

CONTACT

• Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, Czech Republic.
• info@solight.cz
• www.solight.cz.

References

• SOLIGHT.cz | Váš B2B partner a velkoobchod pro Osvětlení, Elektro, Smart Home, Měřící techniku a dalších 1500+ produktů

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>