IE UCM Universal Camera Mount User Manual
- June 11, 2024
- Camera
Table of Contents
IE UCM Universal Camera Mount
Introduction
The UCM Universal Camera Mount is a camera alignment system that allows adjustment of the DUT (device under test) along X, Y, and Z axes. The system is based on linear guidance in combination with a cross focusing rack and ball head. The end position can be fixed with the locking wheels. Please read the manual carefully before using the device to avoid inappropriate utilization that may cause damage to the device, DUT, and/or other components of your setup. Keep these instructions in a safe place and pass them on to any future user.
Intended Use
The UCM Universal Camera Mount is intended for use as a camera alignment
system for adjusting the DUT along X, Y, and Z axes.
Product Variants
The UCM Universal Camera Mount is available in different product variants.
Foreseeable Misuse
Foreseeable misuse of the UCM Universal Camera Mount includes stuck linear
guidance/ball head, hot/cold environment, and risk of tipping over.
Stuck Linear Guidance/Ball Head
If you cannot turn the wheels for X, Y, and Z translation or the ball head,
loosen the locking wheels and check the ball head joint and any moving parts
for debris.
Hot/Cold Environment
If you use UCM in a very hot or cold environment (for example in combination
with iQ-Climate Chamber), please allow the device to approach room temperature
again before manipulating it to avoid injuries or mechanical failure.
Risk of Tipping Over
Only applies to UCM variant 1 (with rectangular frame): When attaching a
heavier DUT to UCM and moving the slide all the way to the front of the
Z-rail, a counter weight on the back of the frame is highly recommended to
keep UCM from tipping over and potentially damaging your equipment.
Getting Started
Scope of Delivery
The UCM Universal Camera Mount comes with the necessary parts to assemble
the camera alignment system.
Operating Instructions
Follow the instructions provided in the manual for assembling and operating the UCM Universal Camera Mount. Adjust the DUT along X, Y, and Z axes using the linear guidance and ball head. Fix the end position with the locking wheels.
Preparing UCM variant 2
Follow the instructions provided in the manual for preparing UCM variant 2.
Additional Information
Disposal Instructions
Follow local regulations for disposing of the UCM Universal Camera Mount.
Technical Data Sheet
For technical specifications, refer to the Technical Data Sheet provided
with the UCM Universal Camera Mount.
PRODUCT INTRODUCTION
Important information: Read the manual carefully before using the device.
Inappropriate utilization may cause damage to the device, to the DUT (device
under test) and/or other components of your setup.
Keep these instructions in a safe place and pass them on to any future user.
Intended use
Camera alignment system based on a linear guidance in combination with a cross
focusing rack and ball head allows adjustment of the DUT along X, Y and Z
axes. Fix the end position with the locking wheels.
- Only suitable for indoor use.
Product variants
UCM is available in two variants:
- Variant 1: with rectangular frame and adjustable feet to place device on any flat surface
- Variant 2: without frame (Z-rail is then screwed directly to the place of operation. Please note: drilling additional holes suiting your setup will be required).
Foreseeable missuse
Stuck linear guidance / ball head
If you cannot turn the wheels for X, Y and Z translation or the ball head,
loosen the locking wheels and check the ball head joint and any moving parts
for debris.
Hot/cold environment
If you use UCM in a very hot or cold environment (for example in combination
with iQ-Climate Chamber), please allow the device to approach room temperature
again before manipulating it to avoid injuries or mechanical failure.
Risk of tipping over
Only applies to UCM variant 1 (with rectangular frame):
When attaching a heavier DUT to UCM and moving the slide all the way to the
front of the Z-rail, a counter weight on the back of the frame is highly
recommended to keep UCM from tipping over and potentially damaging your
equipment.
STARTED INFORMATION
Scope of delivery
- UCM – Universal Camera Mount
- Novoflex Ball 19P ball head for rotation adjustment
- Novoflex QPL1 camera coupling plate for vertical camera mounting
- Novoflex QPL Slim VERTIKAL for horizontal camera mounting
- Piece of black molleton to prevent stray light
- Manual
**Operating instructions
**
Setting up for operation
Depending on the desired orientation of your camera, select one of the
included quick release plates.If necessary, the small ball head additionally
allows free rotation around all axes in both horizontal and vertical
orientations. Figure 2 shows two possible setups. Since this system is
standard 1/4 inch camera thread, UCM can also be combined with your personal
equipment.
**UCM operating elements
**
Cross focusing rack:
Camera positioning (X- and Y-axes)
Fix the quick release plate to the DUT, place it in the quick release clamp
and tighten it down using knob 1 (Figure 3). To position the slide, make sure
knob 2 (Figure 3) is loosened, then turn knob 3 (Figure 3) to move the slide.
After reaching the desired position, tighten knob 2 down again to secure the
slide against accidental movement.
Repeat process for remaining slide.
The marked screws in Figure 4 allow for additional adjustment range on the Y-axis. Simply loosen both screws until you can slide the whole cross focusing rack up or down the profile. After reaching the desired position, tighten the screws again.
Loosen thumb screw (Figure 5, marker 1) and move the Z-slide to the desired position. Then, tighten the thumb screw down again to secure the Z-slide against accidental movement.
Covering reflective/ light emitting parts during measurements
Depending on your setup and device under test, you might encounter unwanted
stray light in your measurements. To counter this, we included a piece of
thick, black molleton with a size of 85×85 cm. Since DUTs vary greatly in
shape and size, we have not prepared a cutout but leave it up to you to apply
a cutout that best suits your requirements.
Preparing UCM variant 2
If you need a Z-rail longer than 350mm, please let us know when you place your
order or preferably beforehand.
The Z-rail for UCM variant 2 is supplied without any holes. Figure 6 shows an
example of how the rail could be prepared for mounting.
UCM variant 1 for example is delivered with holes with a diameter 5.5mm. To
ensure sufficient stability, it is not recommended to use a smaller drill
diameter and/or screws smaller than M5.
For assembly work, the Z-slide holding the cross focusing rack easily slides
on and off each end of the Z-rail.
ADDITIONAL INFO
Disposal instructions
After the service life of UCM, it must be disposed of properly. Observe
your national regulations. Make sure that UCM cannot be used by third parties
after disposing of it.
Contact Image Engineering if assistance for disposal is required.
TECHNICAL DATA
The technical data sheet can be downloaded at the website of Image Engineering as well: www.image-engineering.com.
Overview
| Product name | UCM – Universal Camera Mount |
|---|---|
| Principle | Camera alignment system based on a linear guidance in combination |
with a cross focusing rack and ball head
Features
DUT positioning device
| Travel distance X-axis | 280mm |
|---|---|
| Travel distance Y-axis | approx. 260mm, depending on setup |
| Travel distance Z-axis | 220mm |
General description hardware
| Dimension [W x H x D] | 240mm x 405mm (max.) x 350mm |
|---|---|
| Weight | 3.4kg |
| Scope of delivery | Universal Camera Mount, Novoflex Ball 19P ball head, |
Novoflex coupling plate QPL1, Novoflex QPL Slim VERTIKAL, black molleton,
manual
Temperature range| -30°C up to 120°C
**Requirements on device under test (DUT)**
- Max. DUT weight 0,5kg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>