SOLIGHT WM59-WW LED COB Strip Instructions
- May 15, 2024
- Solight
Table of Contents
SOLIGHT WM59-WW LED COB Strip
Product Information
Technical Specifications
- Product Code: WM59-WW
- Power Input: 8W/m
- Luminous Flux: 800lm/m
- Light Temperature:
- 3000K (Warm White)
- 4000K (Neutral White)
- 6000K (Cool White)
- IP Coverage: IP20
- LED Lifetime: 50,000 hours
- Tape Length: 5m
Product Usage Instructions
- Clean the surface where you will stick the LED strip.
- Adjust the length of the tape as needed, ensuring connectors are purchased for reconnection.
- Peel off the covering layer to expose the adhesive tape on the bottom of the LED strip and attach it to the surface.
- Plug the power adapter into a power outlet to activate the LED strip.
Additional Notices
- For optimal performance, install the LED strip on an aluminium substrate to prevent overheating.
- The LED strip comes with a power adapter with specifications: AC 230V / DC 12V, 2500mA.
- When using a 5m strip length, expect a decrease in luminous flux and power consumption per meter compared to advertised values.
- Avoid exposing the luminaire to heat sources, moisture, direct rain, or immersion in water. It is designed for indoor use only.
- Periodically clean the luminaire with a dry or damp cloth while it is unplugged.
End of Service Life
The light source in this luminaire is non-replaceable. When it reaches the end of its service life, the entire luminaire should be replaced and disposed of properly.
Frequently Asked Questions
- Q: Can the LED strip be cut to a shorter length?
- A: Yes, the LED strip can be shortened as required. The remaining parts can be reused.
- Q: Is the LED strip suitable for outdoor use?
- A: No, the LED strip is intended for indoor use only. Avoid exposing it to direct rain or immersion in water.
- Q: How should I clean the luminaire?
- A: Periodically wipe the luminaire with a dry or damp cloth when it is unplugged to maintain its cleanliness.
Dear customer, thank you for purchasing our product. Please read the following instructions carefully and follow them to serve you safely and to your full satisfaction. This will prevent misuse or damage. Avoid unprofessional handling of this appliance and always observe the electrical appliance usage guidelines. Keep the instruction manual carefully
TECHNICAL PARAMETERS
Product code| Power
input
| Luminous
flux
| Light
temperature
| IP
coverage
| LED lifetime| Tape length
---|---|---|---|---|---|---
WM59-WW| 8W/m| 800lm/m| 3000K| IP20| 50 000 h| 5m
WM59-NW| 8W/m| 800lm/m| 4000K| IP20| 50 000 h| 5m
WM59-CW| 8W/m| 800lm/m| 6000K| IP20| 50 000 h| 5m
INSTALLATION
- Clean the surface which you are going to stick the LED strip.
- Adjust the length of the tape as needed. The remaining parts can be reused. Connectors must be purchased for reconnection.
- The LED strip is equipped with adhesive tape on the bottom. Peel off the covering layer and glue the strip.
- Finally, plug the power adapter into a power outlet.
NOTICE
- For maximum durability and performance, install the tapes on an aluminium substrate (in aluminium profiles) to prevent overheating.
- The strip is equipped with a power adapter with a switch: AC 230V / DC 12V, 2500mA.
- As the length of the LED strip increases, the luminous flux (lm) and power consumption (W) per 1m decreases. With a 5m strip length, the values per 1m decrease by about 25% compared to the values shown.
- The strip can be shortened as required (the remaining parts can be further used).
- Avoid placing the luminaire near objects that are a source of heat or moisture.
- Do not look directly at a lit luminaire for long periods of time as this may cause discomfort or damage to your eyes.
- Do not expose the luminaire to the outdoors, direct rain or immerse it in water. The luminaire is intended for indoor use.
- Periodically wipe the luminaire with a dry or damp cloth only when the luminaire is unplugged.
The light source of this luminaire is non-replaceable, at the end of its service life the entire luminaire must be replaced and disposed of in a designated place. This product contains a light source that for design reasons cannot be removed for verification and therefore the entire product is considered a light source. The power cord cannot be replaced if damaged, the unit must no longer be used.
Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, Czech Republic
“`
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>