Dewalt DWHTGR50 Ceramic Glue Gun Instruction Manual
- July 24, 2024
- Dewalt
Table of Contents
Dewalt DWHTGR50 Ceramic Glue Gun
Ceramic Glue Gun DWHTGR50
Glue Gun Instruction Leaflet
CAUTION: Read Safety Rules and Operating Instructions Carefully
WARNING:
When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury.
READ ALL SAFETY INSTRUCTIONS
- Keep children away.
- Do not touch the nozzle area or melted glue.
- Keep the work area clean. The work environment should be clean, dry well lit, and clear of flammable materials.
- Guard against electric shock. Prevent body contact with grounded surfaces like pipes and appliances. Do not use near water.
- Inspect extension cords.
- Always use safety glasses.
- Don’t abuse the cord. Never carry the tool by the cord or yank the cord to disconnect it from the plug or receptacle.
- Disconnect tools when not in use.
- Avoid accidental glue discharge. Do not touch the glue stick or trigger except to dispense glue.
- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
- When not in use, the tool should be stored indoors.
- Do not pull glue sticks from the gun. The feed mechanism may become damaged or impaired. If you desire to change types of glue, cut off the protruding end and feed the remainder through with the new type of glue.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.
Precautions
Safety Precautions:
- Do not touch the nozzle area of the glue gun or melted glue.
- Do not make repairs to the glue gun.
- Do not use a damaged glue gun.
- Do not allow the glue gun to come in contact with water, liquids, or rain.
- Do not carry the tool by the cord or pull the cord to disconnect it from the outlet.
- For interior use only.
- Do not leave the glue gun unattended during use.
- Do not attempt to remove unused glue from the glue gun after use.
- Place the glue gun in the upright position when idle using the fold-down stand provided.
- Do not use this product in areas where the risk of explosion is present.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similar qualified persons in order to avoid a hazard.
ELECTRIC RATING:
- INPUT: 120 VAC 60Hz
- POWER: 50W
WARNING:
- WHEN GUN IS HOT, DO NOT LAY IT ON ITS SIDE.
- MELTED GLUE WILL BURN SKIN.
- OPERATING TEMPERATURE OF THE NOZZLE IS 380°F (193°C). DO NOT TOUCH THE NOZZLE OR MELTED GLUE.
- THIS TOOL MUST BE PLACED IN ITS STAND WHEN NOT IN USE.
APPLICATIONS AND REPAIRS
- Sealing windows, tiles & bathroom fixtures
- Repair bookbindings, shoe, or loose carpeting
- Dried floral arrangement
- Electrical insulation
- Cardboard
- Crevices
- Paper
- Woodworking
- Plastics
- Foam
- Fabrics
OPERATING INSTRUCTIONS
IMPORTANT: Please read carefully before using your electric glue gun
- Plug your glue gun into an electrical outlet.
- To open the fold-away stand, take hold of the flanges on both sides of the stand and pull forward, until the stand locks into position.
- Insert standard (1/2” inch or 12mm diameter) glue stick. Two glue sticks are needed for first-time use.
- Wait 2 minutes for the glue and glue gun to heat up initially.
- Glue is fed by simply pulling the trigger. The amount of glue is determined by how far the trigger is pulled.
- Unplug tool after use if it will not be used within a 30 minute period.
- Do not attempt to remove unused adhesive from the gun after use. Any unused adhesive can be stored in the gun, reheated, and used later.
TIPS ON USING
- The working time of the hot melts can be extended to 50 to 60 seconds by applying the adhesive in large drops (1/2” diameter) or shortened to less than 10 seconds by extruding the adhesive in thin lines.
- Large areas are difficult to bond because the adhesive frequently will harden before you have extruded the required amount.
- Preheat surfaces (especially metals) to improve bond strength. Direct sunlight will accomplish this.
- The adhesive remaining in an unheated glue gun will remain upon heating.
- Do not use items that will be subjected to temperatures above 140° F (60° C).
- Do not use hot melt to hold heavy loads.
- Some paints and stains can weaken the adhesive. You may need to paint or stain before gluing.
Available Stanley® Glue Sticks for this Glue Gun
| Part No | Applications |
|---|---|
| GS15DT | Dual Melt: for bonding heat-sensitive material, as well as general |
GS20DT
GS25DT
|
GS230S| All Purpose: Clear sticks for fast repairs and hobby projects.
GS230-24
GS230-3
|
GS220-BK| All Purpose Transparent: Sticking on wood, leather
GS220-24
|
GS240-24| Electrical: for sticking on cables, electric leads, PVC, carpet
floor covering
|
GS260| Wood Working: transparent Hot Melt glue
GS264BK
|
GS500| Super Strength: for stronger bonds in a wide variety of materials
79002772
© 2013 DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 1-800-4-DEWALT (1-800-433-9258)
FREQUENTLY ASKED QUESTIONS
What is the Dewalt DWHTGR50 Ceramic Glue Gun?
The Dewalt DWHTGR50 Ceramic Glue Gun is a high-performance tool designed for bonding ceramic materials, providing efficient and reliable adhesive application.
What are the dimensions of the Dewalt DWHTGR50 Ceramic Glue Gun?
The dimensions of the Dewalt DWHTGR50 Ceramic Glue Gun are 11.3 L x 2.6 W x 7.79 H inches.
What is the weight of the Dewalt DWHTGR50 Ceramic Glue Gun?
The Dewalt DWHTGR50 Ceramic Glue Gun weighs 14.4 ounces.
What power source does the Dewalt DWHTGR50 Ceramic Glue Gun use?
The Dewalt DWHTGR50 Ceramic Glue Gun is hand-powered.
What materials is the Dewalt DWHTGR50 Ceramic Glue Gun compatible with?
The Dewalt DWHTGR50 Ceramic Glue Gun is compatible with ceramic materials.
What is the UPC of the Dewalt DWHTGR50 Ceramic Glue Gun?
The UPC of the Dewalt DWHTGR50 Ceramic Glue Gun is 076174766660.
Who is the manufacturer of the Dewalt DWHTGR50 Ceramic Glue Gun?
The manufacturer of the Dewalt DWHTGR50 Ceramic Glue Gun is DEWALT.
What is the item model number of the Dewalt DWHTGR50 Ceramic Glue Gun?
The item model number of the Dewalt DWHTGR50 Ceramic Glue Gun is DWHTGR50.
What material is the Dewalt DWHTGR50 Ceramic Glue Gun made from?
The Dewalt DWHTGR50 Ceramic Glue Gun is made from a blend of materials.
What is the warranty description for the Dewalt DWHTGR50 Ceramic Glue Gun?
The Dewalt DWHTGR50 Ceramic Glue Gun comes with a limited lifetime warranty.
What is the price of the Dewalt DWHTGR50 Ceramic Glue Gun?
The Dewalt DWHTGR50 Ceramic Glue Gun is priced at $21.59.
What should I do if the Dewalt DWHTGR50 Ceramic Glue Gun doesn’t turn on?
Ensure the Dewalt DWHTGR50 Ceramic Glue Gun is plugged into a working power outlet. Check the power cord for any visible damage.
Why is the Dewalt DWHTGR50 Ceramic Glue Gun not heating up?
Verify that the glue gun is properly plugged in and turned on. Allow a few minutes for the gun to heat up.
How do I clean the Dewalt DWHTGR50 Ceramic Glue Gun if there is glue buildup?
Unplug the glue gun and let it cool down completely. Use a scraper or soft cloth to remove excess glue. For stubborn buildup, gently heat the glue gun and wipe off the softened glue. Avoid using abrasive cleaners.
What should I do if the Dewalt DWHTGR50 Ceramic Glue Gun leaks glue excessively?
Ensure you are using the correct size glue sticks. If the glue gun continues to leak, it might be due to a damaged nozzle or an internal issue.
DOWNLOAD THE PDF LINK:Dewalt DWHTGR50 Ceramic Glue Gun Instruction Manual
REFERENCE:Dewalt DWHTGR50 Ceramic Glue Gun Instruction Manual- Device.Report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>