ferm LIVING HEMI Elegant Lounge Chair Instruction Manual
- July 23, 2024
- ferm LIVING
Table of Contents
ferm LIVING HEMI Elegant Lounge Chair
Product Information
Specifications
- Product: HEMI LOUNGE CHAIR
- Material: Weight-bearing textile
- Adjustable seat height
- Care: Dry clean only
Product Usage Instructions
- Place the seat frame (A) on the side. Attach the backrest frame (B) and the front legs (C) to the seat frame (A) using two screws each.
- Secure the remaining four screws.
- Insert the canvas seat with the wide end first. Then, insert the front stick (D) into the canvas seat.
- Insert the narrow part of the canvas seat and tuck the backrest stick (E) into the canvas seat.
- For additional product overview and material descriptions, please visit our website at www.fermliving.com. For any questions or comments, contact us at info@fermliving.com.
FAQ
- Q: Can the seat height be adjusted?
- A: Yes, the height of the seat can be adjusted by moving the front stick to the other tunnel.
- Q: How should I clean the seat?
- A: The seat should be dry cleaned only to maintain its quality.
General Instructions
PLEASE READ BEFORE INSTALLATION
WARNING
The safety of this fitting can only be guaranteed if the following
instructions are observed during both installation and use. Please retain
these instructions safely after installation.
PLEASE OBSERVE THE FOLLOWING GUIDELINES
WOOD FURNITURE:
Wood is a natural material – no two pieces of wood are the same – which is why
there are no two identical pieces of wooden furniture. Wood is constantly
changing, which means that its structure and color evolve. The biggest changes
occur at the beginning of a piece of furniture’s life. Solid wood is mainly
affected by seasonal changes in humidity. During the summer, wood expands and
may cause tabletops to bow slightly. During the winter, the wood contracts
again.
Wood movement – expanding and contracting – can cause ’checks’ (small splits
and cracks between the wood’s veins) to appear. However, these do not damage
the product and can usually be treated with a wood oil treatment. To maximize
the lifespan of wooden furniture, it is important to ensure that it is
continuously cared for and maintained. Below are guidelines on how to best
treat and maintain your furniture made of solid wood. Using a neutral wood oil
will help the wood retain its original color, give it a water-repelling
effect, and prevent it from drying out. Apply oil with a soft sponge or soft,
lint-free cloth in the direction of the wood grain in a continuous thin layer.
Allow the oil to dry then wipe with a soft, lint-free cloth to remove any
excess oil. Daily cleaning (wiping the surface after a meal, for example)
slowly removes oil from the wood, which is why it is recommended that you
treat the wood 4–6 times a year or as needed.
Please read the instructions on the bottle before treatment.
For a more thorough cleaning of your wooden furniture, you should use a wood
cleaner, which removes marks like oil-based stains, water rings, and more. It
can also be used to wash tannic acid out of oak wood. Remember to treat the
surface with neutral wood oil after using a wood cleaner. Always remember to
treat the underside of your furniture; otherwise, there is a risk that the
wood will warp or crack. If the surface of the wood ‘rises up’ (becomes rough)
after treatment, you can lightly sand it in the direction of the wood grain
using fine sandpaper (minimum 200 grit). Never use steel wool!
The seat is made of a weight-bearing textile and may stretch due to the linen
natural material. The height of the seat can be adjusted by moving the front
stick to the other tunnel. Dry clean only.
MORE INFORMATION
To access further information such as product overview and material
descriptions, please visit our website at
www.fermliving.com. If you have any questions or
comments, please do not hesitate to contact us at
info@fermliving.com.
Box Content
NEEDED TOOLS
Assembly Process
- Put the seat frame (A) on the side. Mount the backrest frame (B) and the front legs (C) to the seat frame (A) with two screws each.
- Attach the remaining four screws.
- Insert the canvas seat with the wide end first, then put the front stick (D) into the canvas seat.
- Now insert the narrow part of the canvas seat, then tuck the backrest stick (E) into the canvas seat.
