ferm LIVING Bon Hallway Cabinet Instruction Manual
- July 18, 2024
- ferm LIVING
Table of Contents
ferm LIVING Bon Hallway Cabinet
Product Information
Specifications:
- Product: BON HALLWAY CABINET
- Tools Needed: Electrical drill, Spirit Level, Screwdriver, Pencil, Hammer
- Box Content:
- 1 Mirror
- 1 Shelf
- 1 Coat Rod
- 1 Wall Module
- 8 Dowel
- 3 Long Screw
- 4 Short Screw
- 3 Wallplug
- 5 Minifix Screw
- 5 Minifix Connector
Product Usage Instructions
Assembly Process 1:
Insert 4 dowels in the shelf.
Assembly Process 2:
Mount the shelf on the wall module with four short screws.
Assembly Process 3:
TWO PERSONS REQUIRED
Recommended: Use spirit level Mark and drill holes, and attach the wall module to the wall with three big screws and three wall plugs. *Depending on the type of wall, replace the supplied screws with screws and wall plugs that match the type of wall.
Assembly Process 4:
Insert minifix connectors and dowels to the wall module.
Assembly Process 5:
Put the minifix screws into the mirror.
Assembly Process 6:
Mount the mirror on the wall module, with the coat rod in between. Then lock the minifix connectors.
For more information, visit fermliving.com
FAQ
- Q: Can I use this cabinet on plaster walls?
- A: No, the raw plugs provided are suitable for brick walls only.
- Q: What should I do if I encounter difficulties during installation?
- A: If you have any questions or encounter difficulties during installation, please contact us at info@fermliving.com for assistance.
General Instructions
PLEASE READ BEFORE INSTALLATION
WARNING:
The safety of this fitting can only be guaranteed if the following instructions are observed during both installation and use. Please retain these instructions safely after installation
PLEASE OBSERVE THE FOLLOWING GUIDELINES FOR VENEERED FURNITURE:
For daily cleaning, wipe with a clean, dry cloth or a cloth wrung out in clean water. If a wrung-out cloth or chamois is used, immediately wipe away any excess water with a clean, dry cloth. Dirty surfaces should be wiped with a damp cloth. Again, dry immediately with a clean, dry cloth. Be aware that liquid detergents will dissolve the oil, so an oil treatment should be repeated. To do this, apply wood oil evenly with a soft cloth or sponge in the direction of the wood’s grain. After 2-3 hours, the wood may be polished with a clean, dry cloth. Avoid exposing the surfaces to water or other liquids for an extended period of time. Spilt liquids should be wiped away immediately.
For a more thorough cleaning of your wooden furniture, you should use a wood cleaner, which removes marks like oil-based stains, water rings, and more. It can also be used to wash tannic acid out of oak wood. Remember to treat the surface with neutral wood oil after using wood cleaner. Always remember to treat the underside of your furniture; otherwise, there is a risk that the wood will warp or crack. If the surface of the wood ‘rises up’ (becomes rough) after treatment, you can lightly sand it in the direction of the wood grain using fine sandpaper (minimum 220 grit). Never use steel wool!
The enclosed raw plugs are for brick walls only. Not suitable for plaster walls
MORE INFORMATION:
To access further information such as product overview and material descriptions, please visit our website at www.fermliving.com. If you have any questions or comments, please do not hesitate to contact us at info@fermliving.com.
NEEDED TOOLS
Box Content
Assembly Process
Insert 4 dowels in shelf. 
mount the shelf on the wall module with four short screws.
Mark and drill holes, and attach the wall module to the wall with three big
screws and three wallplugs.
Depending on the type of wall, replace the supplied screws with screws and
wallplugs that match the type of wall. 
Insert minifix connectors and dowels to the wall module. 
Put the minifix screws into the mirror. 
Mount the mirror on the wall module, with the coat rod in between.
Then lock the minifix connectors.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>