KARCHER Puzzi 9/1 Series BP Textile Washer Instructions

KARCHER Puzzi 9/1 Series BP Textile Washer

General notes

Before using for the first time, read the enclosed original instructions of this device, the battery pack and the charger as well as the safety instructions. Act in accordance with them.
Keep these documents for future reference or for future owners.

• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
• Notify the dealer immediately in the case of shipping damage.
• Check the package contents when unpacking for missing accessories or for damage.

Environmental protection

The packing materials can be recycled. Please dispose of the packaging in accordance with environmental regulations.
Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH

Intended use

• This spray extraction device is intended for wet cleaning of upholstery, upholstered furniture and small carpeted areas.
• This device is suitable for commercial use

Overview of the device

Quick Start Guide

Illustration A

1. Inserting the battery pack
2. Connect the spray/suction hose to the device, connect the spray/suction hose to the manual nozzle
3. Mix cleaning solution, fill fresh water tank
4. Selecting operating modes
5. Cleaning
6. Emptying the fresh water tank
7. Empty the wastewater container
8. Fill the fresh water tank (without detergent), rinse the device
9. Clean the fluff filter, clean the fresh water filter
10. Removing the battery pack
11. Allow the device to dry

Description of the device

Illustration B

1. Manual nozzle for upholstery cleaning
2. Hose hook
3. Fastening eyelet
4. Tray for 3 nozzle mouthpieces
5. Unlocking button
6. Holder for accessories
7. Rechargeable battery pack
8. Spray switch
9. LED, spraying
10. LED, suction
11. Suction switch
12. Casing
13. Type plate
14. Steering roller
15. Spray hose connection
16. Floor nozzle for carpet cleaning (Adv only)
17. Carpet adapter
18. Floor nozzle latch
19. Suction hose connection
20. Cover
21. Fresh water tank
22. Device carrying handle including suction pipe holder
23. Nozzle mouthpiece (red)
24. Union nut
25. Suction pipe (Adv only)
26. Nozzle mouthpiece (green)
27. Handle (Adv only)
28. Angle piece (Adv only)
29. Lever on the manifold
30. Lever on manual nozzle
31. Spray hose
32. Suction hose
33. Spray / suction hose
34. Quick Start Guide
35. Wastewater container, removable
36. Wastewater container carrying handle
37. Cover seal
38. Fluff filter
39. Fresh water filter

Table of nozzle mouthpieces

Colour| Part number| Flow volume| Applica tion| Approved for device
---|---|---|---|---
Yellow| 6.415-| 2.0 l/min| Floor noz-| Puzzi 10/2
 | 165.0|  | zle|
Green| 6.415-| 1.2 l/min| Floor noz-| Puzzi 9/1 Bp
 | 105.0|  | zle|
Brown| 6.415-| 1.0 l/min| Floor noz-| Puzzi 8/1,
 | 166.0|  | zle| Puzzi 10/1
Blue| 6.415-| 1.0 l/min| Uphol-| Puzzi 8/1,
 | 928.0|  | stery noz-| Puzzi 10/1,
 |  |  | zle| Puzzi 10/2,
 |  |  |  | Puzzi 30/4
Red| 6.415-| 0.55 l/min| Uphol-| Puzzi 9/1 Bp
 | 097.0|  | stery noz-|
 |  |  | zle, short|

Initial startup

Check hoses for damage before each startup.

Installing accessories

1. Adv only: Fit the suction pipe onto the floor nozzle and hand-tighten the union nut on the floor nozzle.
2. Adv only: If necessary, slide the handle onto the suction pipe and hand-tighten in the desired position.
3. Adv only: Fit the angle piece onto the suction pipe and hand-tighten the union nut on the angle piece.
4. Connect the suction hose to the suction hose connection on the device. Insert the spray hose coupling into the spray hose connection on the device and latch into place.
5. Connect the suction hose to the manual nozzle or the elbow. Connect the spray hose coupling to the manual nozzle or angle piece and latch into place.

Mixing the cleaning solution

Danger from detergents

Risk of injury and damage
Observe all instructions that are included with the detergents used.
Note
Warm water (maximum 50 °C) increases the cleaning effect. Check the temperature resistance of the surface to be cleaned.
Note
Use detergents sparingly to conserve the environment.

1. Mix fresh water and detergent in a clean container (concentration as specified for the detergent). Dissolve the detergent in the water.

Filling the fresh water tank

1. Pour the cleaning solution into the freshwater tank.
2. The filling level must not exceed the “MAX” mark.

Defoaming agent

Note
Foam is generated in the wastewater container when cleaning previously shampooed carpets. Foaming can be prevented by adding defoaming agents.

1. Add defoaming agent (special accessory) to the wastewater container.

Inserting the battery pack

1. Slide the battery pack into the battery holder and lock it in place.

Charging the battery pack

Note
Read the operating instructions of the charger, especially the safety instructions!
Note
Read the operating instructions of the battery pack, especially the safety instructions!
Note
The battery pack is partially charged on delivery.
Charge before use and when necessary.
Note
The battery pack can only be charged when it is removed.

1. Press the unlocking button and remove the battery pack.
2. Charge the battery pack according to the operating instructions of the charger and battery pack.

Operation

Switching on the device

1. Press the spray switch to switch on the spray pump.
   • The spray LED lights up.
2. Press the suction switch to switch on the suction turbine. The suction LED lights up.

Cleaning mode

Danger from cleaning solution

Risk of damage
Before using the device, check the object to be cleaned for colour fastness and water resistance in an inconspicuous place.

1. Remove loose dirt from the object to be cleaned.
2. Press the lever on the manual nozzle or angle piece to spray the cleaning solution.
3. Run over the surface to be cleaned in overlapping paths. Pull the nozzle backwards (do not push).
4. Adv only: When work is interrupted, the floor nozzle can placed in the device carrying handle.
5. When changing the nozzle, the manual nozzle can be inserted into the holder for accessories.

Switching off the device

1. Switch off the spray switch and the suction switch.
2. The LEDs extinguish.

Empty the wastewater container

1. Switch off the suction switch and the spray switch when the wastewater container is full.
2. Remove the cover.
3. Remove the wastewater container from the device and empty it.

Emptying the fresh water tank

1. Switch off the device.
2. Briefly operate the lever on the manual nozzle or angle piece to relieve pressure.
3. Disconnect the manual nozzle or angle piece from the spray/suction hose.
4. Hang the suction hose in the fresh water tank.
5. Press the suction switch to switch on the suction turbine.
6. Suck the fresh water tank empty and switch off the device.
7. Remove the cover.
8. Remove the wastewater container from the device and empty it.

Flushing the device

1. Connect the manual nozzle or angle piece (with suction pipe and floor nozzle) to the suction hose.
2. Connect the spray hose coupling to the manual nozzle or angle piece and latch into place.
3. Pour approximately 2 litres of tap water into the fresh water tank. Do not add detergents.
4. Press the spray switch to switch on the spray pump.
5. Hold the manual or floor nozzle over a drain.
6. Operate the lever on the manual nozzle or angle piece and flush the device for 1 to 2 minutes.
7. Switch off the device.
8. Remove the wastewater container from the device and empty it.

Each time after use

1. Flush the device.
2. Drain the wastewater container and clean it under running water.
3. Empty the fresh water tank.
4. Clean the exterior of the device with a damp cloth.
5. To avoid unpleasant smells, remove all water from the device before long downtimes.
6. Let the device dry thoroughly: Remove the cover or move it to the side.
7. Clean the fluff filter and fresh water filter (see “Care and maintenance”).

Storing the device

1. Store the spray/suction hose and manual nozzle as shown in the illustration.
   Illustration C
   

2. Store the device in a dry room and secure it against unauthorised use.

Cleaning methods

Normal soiling

1. Spray and vacuum up the cleaning solution in one step.

Note
Repeated vacuuming without spraying shortens the drying time.

Heavily soiling or stains

1. Apply cleaning solution with the suction turbine switched off and let it work for 10 to 15 minutes.
2. Clean the area as with normal soiling.

Upholstery cleaning

1. Adv only: Fit the manual nozzle instead of the floor nozzle.
2. Use less detergent for sensitive fabrics and spray the surface at a distance of approx. 200 mm. Then only vacuum.

Cleaning tips

• Spray heavily soiled areas in advance and allow the cleaning solution to work for 5 to 10 minutes.
• Always work from light to shadow (from window to door).
• Always work from the cleaned to the uncleaned area.
• The more sensitive the covering (oriental bridges, Berber, upholstery fabric) the lower the concentration of detergent.
• Carpets with jute backs can shrink and bleed in colour if the work is too wet.
• Brush wet pile carpets in the direction of the pile after cleaning when wet (e.g. with a fibre brush or scrubber).
• Impregnating after wet cleaning prevents the textile from being quickly soiled again.
• To avoid pressure points or rust stains, do not walk on or furnish the cleaned area until after it has fully dried.
• To improve the cleaning result, rinse the object with clean water after using detergents.

Detergent

powder

| 1 %| 6.295-175.0
CarpetPro clean- er, iCapsol (16 piece)| RM 760

tabs

| 2 tabs for 8 litres| 6.295-850.0
CarpetPro clean- er, quick-drying (10 litre)| RM 767 liq- uid| 1.2 %| 6.295-198.0
CarpetPro clean- er (10 litres)| RM 764 liq- uid| 1 %| 6.295-854.0
CarpetPro im- pregnation (5 li- tres)| RM 762 liq- uid| 20 %| 6.295-852.0
Defoaming (2.5 li- tres)| RM 761 liq- uid| 0.5 %| 6.291-389.0

For further information, please request the product information sheet and the EU safety data sheet for the relevant cleaning agent.

Transport

Failure to observe the weight

• Risk of injury and damage

• Be aware of the weight of the device during transportation.

  1. Place the suction pipe on the carrying handle of the device.
     Illustration D
     

  2. When transporting the device in vehicles, secure it to prevent it from slipping or overturning in accordance with the respective valid guidelines.

Storage

Failure to observe the weight

• Risk of injury and damage
• Be aware of the weight of the device during storage.
• The device may only be stored indoors.
• Press the unlocking button and remove the battery pack to prevent discharge.

Care and service

Danger of electric shock

• Injuries due to touching live parts
• Switch off the device.
• Remove the battery pack.
• Regularly check the device-side contacts in the battery holder for contamination and clean with a damp cloth if necessary. Do not use detergents.

Clean the fluff filter

1. Remove the cover.
2. Remove the wastewater container from the device.
3. Pull out the fluff filter.
4. Regularly clean the fluff filter under running water. If very dirty, open the frame and replace the fleece.

Clean the fresh water filter

1. Unscrew the fresh water filter.
2. Clean the fresh water filter under running water.

Clean the nozzle

1. Unscrew the union nut.
2. Clean the nozzle mouthpiece.

Troubleshooting guide

Danger of electric shock

• Injuries due to touching live parts
• Switch off the device.
• Remove the battery pack.

Device not running

1. Charge the battery pack.
2. Insert the battery pack.
3. Check the battery pack for correct seating.
4. Switch on the device.
5. Allow the overheated board to cool down.

No water emitted from the nozzle

1. Fill up the fresh water tank.
2. Check the couplings on the spray hose for correct seating.
3. Clean or replace the nozzle mouthpiece.
4. Clean the fresh water filter.
5. Spray pump defective, contact customer service.

Single-sided spray jet
Clean the nozzle mouthpiece.

Poor suction performance

1. Check that the cover is seated correctly.
2. Clean the seal on the cover and the contact surface on the device.
3. Clean the fluff filter.
4. Check the suction hose for clogging; clean if necessary.

Spray pump is loud
Refill the fresh water tank.

Heavy foaming in the wastewater container
Add defoaming agent (special accessory) to the wastewater container.

Customer Service department
If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site.
(See overleaf for the address)

Accessories and spare parts

• Only use original accessories and original spare parts.
• They ensure that the appliance will run fault-free and safely.
• Information on accessories and spare parts can be found at www.kaercher.com.

Spare parts list

Only use KÄRCHER original battery packs, not non-rechargeable batteries.

Declaration of Conformity

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.
Product: Spray retraction device

Type: 1.101-xxx

Currently applicable EU Directives
2006/42/EC (+2009/127/EC)
2011/65/EU
2014/30/EU

Harmonised standards used
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60335-1
EN 60335-2-68
EN 62233: 2008

National standards used

The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01

Declaration of Conformity (UK)

We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.
Product: Spray retraction device

Type: 1.101-xxx

Currently applicable UK Regulations
S.I. 2008/1597 (as amended)
S.I. 2012/3032 (as amended)
S.I. 2016/1091 (as amended)
Designated standards used
EN IEC 63000: 2018
EN 55014-1: 2017 + A11: 2020
EN 55014-2: 2015
EN 60335-1
EN 60335-2-68
EN 62233: 2008

National standards used

The signatories act on behalf of and with the authority of the company management.

Documentation supervisor:
S. Reiser
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28 – 40
71364 Winnenden (Germany)
Ph.: +49 7195 14-0
Fax: +49 7195 14-2212
Winnenden, 2020/10/01

Technical data

Puzzi 9/1 Bp (Adv) (Pack)

Subject to technical modifications.

References

• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International
• Dealer Search | Kärcher International
• Home and Garden Warranty Registration USA - Kärcher

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>