VELOSSA TECH Elantra-N-line-GEN4-BIGMOUTH-LIT-R2 Big Mouth LIT KIT Ram Air Intake Snorkel Installation Guide
- July 22, 2024
- VELOSSA TECH
Table of Contents
- VELOSSA TECH Elantra-N-line-GEN4-BIGMOUTH-LIT-R2 Big Mouth LIT KIT Ram
- Product Information
- Product Usage Instructions
- FAQ
- Kit Contents Full Kit
- Bumper Removal
- Stock Components Removal
- Big Mouth Installation
- Install the LIT BIG MOUTH Flare
- Wiring Harness
- Wiring Harness Schematic
- Controller Placement
- Big Mouth Wiring
- Power Hook-up
- Phone App
- Finalize
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VELOSSA TECH Elantra-N-line-GEN4-BIGMOUTH-LIT-R2 Big Mouth LIT KIT Ram
Air Intake Snorkel
Product Information
Specifications
- Product Name: 2021+ Hyundai Elantra N-Line BIG MOUTH LIT KIT Ram Air Intake
- Installation Time: Approximately 2 hours
- Tools Required: Basic hand tools
Product Usage Instructions
Kit Contents (Full Kit)
| Qty | Component |
|---|---|
| 1 | Diode Dynamics RGBW Controller |
Bumper Removal
REMOVE BUMPER BEFORE ATTEMPTING INSTALLATION. Refer to bumper removal videos on YouTube for guidance.
Stock Components Removal
Remove the stock air scoop and retain the OEM screws for reinstallation.
Big Mouth Installation
Slide the BIG MOUTH over the opening and attach using the OEM hardware. Avoid over-tightening.
Install the LIT BIG MOUTH Flare
- Attach the supplied cable clip to your BIG MOUTH as shown.
- Provide enough slack in the cable to avoid strain.
FAQ
Q: Can I use the extra black wire in the kit to ground the switch gold terminal?
A: Yes, you can use the extra black wire to ground the switch gold terminal, but it is not mandatory for installation.
Kit Contents Full Kit
- Please review this document before attempting installation.
- You will need basic hand tools and about 2 hours of installation time.
| Kit Contents | Qty |
|---|---|
| Diode Dynamics RGBW Controller | 1 |
| Positive Cable w/ In-Line Fuse | 1 |
| Power Cable w/ Pigtail Connector | 1 |
| Switch | 1 |
| Switch Ground Cable w/ Crimped Connector | 1 |
| 8″ Zip Ties | 8 |
| Cable Clip | 2 |
| Assembled LIT KIT BIG MOUTH | 1 |
Kit Contents (LIT Flare Only)
Please review the table below and make sure you have received the kit contents.
| Kit Contents | Qty |
|---|---|
| Diode Dynamics RGBW Controller | 1 |
| Positive Cable w/ In-Line Fuse | 1 |
| Power Cable w/ Pigtail Connector | 1 |
| Switch | 1 |
| Switch Ground Cable w/ Crimped Connector | 1 |
| 8″ Zip Ties | 8 |
| Cable Clip | 2 |
| Assembled LIT KIT BIG MOUTH | 1 |
Bumper Removal
- REMOVE THE BUMPER BEFORE ATTEMPTING INSTALLATION. Use YouTube as a resource, there are many bumper removal videos to guide you.
Stock Components Removal
- Remove the stock air scoop. Hold on to the OEM screws that retain it because they will be reused to install the Big Mouth.
Big Mouth Installation
Slide the BIG MOUTH over the opening and attach using the OEM hardware. DO NOT OVERTIGHTEN.
Install the LIT BIG MOUTH Flare
SKIP THIS SLIDE IF YOU PURCHASED A FULL-LIT KIT
Attach the supplied cable clip to your BIG MOUTH as shown. Fasten the cable and provide enough slack to not strain the cable.
Wiring Harness
Wiring Harness Schematic
Controller Placement
- Zip-tie the controller to the following location behind the driver-side headlight.
- The controller is zip-tied to the thick OEM electrical harness using two zip ties, one zip tie should loop through the DD controller slot and the other zip tie should go around the body and plug.
Big Mouth Wiring
- Ground the controller as shown with the supplied 6mm bolt.
- Snake the Diode Dynamics LED power wire from the BIG MOUTH as shown and connect to one of the four ports into the controller (make sure the arrows are lined up). The other 3 ports can be used for more Diode Dynamics lighting products
- You may zip-tie the other 3 ports as shown.
- Connect the switch according to the wiring harness schematic (slide 9). There will be excess power wire coming out of the power connector, bundle it neatly, and zip-tie tie, leaving about a foot of power wire to make the power connection.
Power Hook-up
Tuck away the bundle as shown, fasten the power lug to the (+) terminal in the fuse box on top of the OEM stud, and use the supplied M6 nut.
Power Hook-up
Switch ground: Optional
- If you would like the switch LED to light up when the switch is on, ground the switch using the supplied ground wire.
- Once complete, put the fuse box cover back on, and ensure no wires are pinched by the fuse box!
Phone App
Download the Diode Dynamics app and connect via Bluetooth.
How to connect to the app:
- After installing the app from the app store, open the app on your device.
- Cycle the power to the Bluetooth controller by unplugging it and plugging it back in or flick the power switch and wait a few seconds, then turn it back on.
- Wait for the app to detect the controller, it will pop up on the app screen as a Bluetooth controller. If necessary, cycle the power once more to refresh the controller.
- Once the controller shows up on the app, click it and connect. You have 30 seconds to select the controller once it shows up on the app. After 30 seconds you will need to refresh again to detect the controller again.
- Note that if you mount your controller behind a lot of metal components, this may degrade the signal and range.
Finalize
Re-install the bumper the same way it was removed and ENJOY!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>