VELOSSA TECH 2018-2020 Hyundai Elantra GTS N-Line Big Mouth Intake Installation Guide

VELOSSA TECH 2018-2020 Hyundai Elantra GTS N-Line Big Mouth Intake

Kit Contents – Full Lit kit

• Please review this document before attempting installation.
• You will need basic hand tools and about 2 hours of installation time.
• Please review the table below and make sure you have received the kit contents.

Kit Contents

• M6 x 30mm Cap Screw: 1
• M6 Large Washer: 1
• Diode Dynamics RGBW Controller: 1
• Positive Cable w/ In-Line Fuse: 1
• Power Cable w/ Pigtail Connector: 1
• Switch: 1
• Switch Ground Cable w/ Crimped Connector: 1
• 8″ Zip Ties: 5
• M6 x 12mm Cap Screw: 1
• M6 Lock Nut: 1
• Assembled LIT KIT BIG MOUTH: 1

Kit Contents – Lit Flares Only

• Please review this document before attempting installation.
• You will need basic hand tools and about 2 hours of installation time.
• Please review the table below and make sure you have received the kit contents

Kit Contents

• Diode Dynamics RGBW Controller: 1
• Positive Cable w/ In-Line Fuse: 1
• Power Cable w/ Pigtail Connector: 1
• Switch: 1
• Switch Ground Cable w/Crimped Connector: 1
• 8″ Zip Ties: 5
• Cable Clips: 1
• M6 x 12mm Cap Screw M6 Lock Nut: 1
• Assembled LIT Flare: 1

Bumper Removal

REMOVE BUMPER PRIOR TO ATTEMPING INSTALLATION. Use YouTube as a resource, there are many bumper removal videos to guide you.

Stock Components Removal

Install the LIT KIT BIG MOUTH

SKIP THIS SLIDE IF YOU PURCHASED A FULL LIT KIT
Attach the supplied cable clip to your BIG MOUTH as shown. Fasten the cable and provide enough slack to not strain the cable.

Big Mouth Installation

Slide the BIG MOUTH over the opening and attach using the provided hardware.

Wiring Harness

Wiring Harness Schematic

Controller

• Zip tie the controller to the following location behind the driver side headlight. The controller is zip tied to the thick OEM electrical harness using two zip ties, one zip tie should loop through the DD controller slot and the other zip tie goes around the body and plug.

• Ground the controller as shown with supplied 6mm bolt.

Wire Management

• Snake the Diode Dynamics LED power wire from the BIG MOUTH as shown and connect to one of the four ports into the controller. The other 3 ports can be used for more Diode Dynamics lighting products.

• You may zip tie the other 3 ports as shown.

Power Hook-up

• There will be excess power wire coming out of the power connector, bundle it neatly and zip tie, leave about a foot of power wire to make the power connection.

• Tuck away the bundle as shown, fasten power lug to (+) terminal in the fuse box on top of the OEM stud, use supplied M6 nut.

• Switch ground: Optional

Phone App

Download the Diode Dynamics app and connect via Bluetooth.

How to connect to the app:

1. After installing the app from the app store, open the app on your device.
2. Cycle the power to the Bluetooth controller by unplugging it and plugging it back in or flick the power switch and wait a few seconds, then turn it back on.
3. Wait for the app to detect the controller, it will pop up on the app screen as a Bluetooth controller. If necessary, cycle the power once more to refresh the controller.
4. Once the controller shows up on the app, click it and connect. You have 30 seconds to select the controller once it shows up on the app. After 30 second you will need to refresh again to detect the controller again.
5. Note that if you mounted your controller behind a lot of metal components, this may degrade the signal and range.

Finalize

Re-install the bumper the same way it was removed and ENJOY!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>