VELOSSA TECH GENESIS-G80-5.0-BM-LIT Dual Big Mouth LIT KIT Ram Air Intake Snorkel Installation Guide

GENESIS-G80-5.0-BM-LIT Dual Big Mouth LIT KIT Ram Air Intake Snorkel

“`html

Specifications:

• Model: Genesis G80 3.3T/5.0/3.8

• Product: BIG MOUTH LIT KIT Ram Air Intake Installation
  Guide

• Installation Time: 1-1.5 hours

• Hardware Reuse: OEM

Product Usage Instructions:

Kit Contents:

Bumper Removal:

Instructions on how to remove the bumper, including the shroud
and screws.

Stock Components Removal:

Steps to remove the OEM components in the correct order.

Stock Inlet Removal:

Details on removing the OEM inlets, screws, and pop-up
clips.

FAQ:

Q: Do I need any special tools for the installation?

A: Basic hand tools are required for the installation, no
special tools needed.

Q: Can the LED extension cable be cut to a shorter length if

needed?

A: It is recommended not to cut the LED extension cable as it
may affect functionality.

“`

Genesis G80 3.3T/5.0/3.8
BIG MOUTH “LIT KIT” Ram Air Intake Installation Guide

Please review this document before attempting installation. You will need basic hand tools and 1-1.5 hours of installation time. This product reuses the OEM hardware.

Kit Contents

Qty

Diode Dynamics RGBW Controller

1

Diode Dynamics 1m LED Extension

1

Positive Cable w/ In-Line Fuse

1

Power Cable w/ Pigtail Connector

1

Switch

1

Switch Ground Cable w/ Crimped Connector

1

8″ Zip Ties

8

16″ Zip Tie

2

Cable Clips

4

M6 lock nut

1

Assembled LIT KIT BIG MOUTH’s

1

Bumper Removal
Remove the shroud by pushing down on the center pin of the pop-up clips and extracting them with a pry tool.

Bumper Removal
After removing the shroud, remove the top 4 screws (10mm) that attach the bumper to the chassis

Bumper Removal
Remove the 3 pop-up clips and 1 screw (8mm) that lie in the wheel well

Bumper Removal
Remove 6 pop-up clips (no screws) that trace the edge of the bumper such as the ones indicated below.

Bumper Removal
As the bumper gets pulled off, take notice of the indicated wiring harness connector. To remove, pull back on the lever shown below. Once it swivels about entirely, pull to disconnect.

Stock Components Removal
To remove the OEM components, there is an order to it: remove the air ducts first and the radiator shroud afterwards. See the following slides for more detail.

Stock inlet
1

Stock shroud
2

Stock inlet
1

Stock Inlet Removal
To remove the OEM inlets, there are 3 (10mm) screws that need to be removed. You will need a 6″ extension to reach the recessed screw. Hold on to these, some of them will be reused.

Stock Inlet Removal
Use a non-marring pry tool to remove the pop-up clip at the top of the inlet. Proceed by removing the inlet.

Shroud Removal
Remove the following screws and repeat for the other half of the shroud.

Shroud Removal
From the backside of the shroud, carefully undo the clips holding the wire loom by pinching as shown in the image. There are numerous clips along the shroud. Once these have been undone, the shroud should be free to remove.

Important Notice
The installations that follow this slide only use coarsethread hardware which you extracted, shown circled in green. The threads are much larger and spaced out. Also, the coarse-thread hardware ends with a sharp point.
IMPORTANT FOR NEXT SLIDE!!!

Big Mouth Install
Position the Big Mouths over the inlets. It may help to loosen the headlight and swivel (no need to fully remove) to properly seat the Big Mouth intakes. Reuse the OEM hardware to install the Big Mouth and take care fasten the headlight again. Carefully slide the Big Mouth intakes over the stock ports and ensure the bolt holes line up. Fasten using OEM coarse-thread hardware. Do not torque down hard.
DO NOT CROSS-THREAD AND MAKE SURE NOT TO OVERTORQUE.

BIG MOUTH Install
Prepare the following locations by wiping down with a clean cloth or paper towel, let dry. Apply the LED cable relief clip as shown.

BIG MOUTH Lit Kit Prep
Plug the supplied Diode Dynamics LED extension cable into the driver side LED as shown and clip into LED cable relief clip.
Take notice of the notch within the M8 female connector. The connectors must be properly oriented and should not require very much force to connect. Improper alignment can damage the pins within the male connector.

Wiring Harness

Power terminal (+)

In-line fuse

Positive wire (+)

Toggle switch

Crimped connectors

Switch ground wire

Ground terminal (-) Ground wire (-)

Power connector Crimped connector

Wiring Harness Schematic

Switch (leave on)
Crimped connector to switch terminal (+)

Gold terminal can be grounded using the wire shown below to allow switch LED to light up when in use.

Crimped connector to switch terminal (A)

12V Power Terminal (+)

Power connector Ground (-)

Fuse
There is an extra black wire in your kit, you can use it to ground the switch gold terminal if preferred, however not mandatory.

BIG MOUTH Lit Kit Routing
Find a place to ground the circuitry and secure the ground ring terminal(s). Use the supplied double-sided tape to place the Diode Dynamics controller in an appropriate location. Connect the power connector and connect the red wires to the switch as shown in slide 18. Set aside about 2 ft of red wire and bundle the excess of the red power wires together using an 8″ zip tie.
Leave 2 ft of wire free
Bundle excess power wire together and zip tie

BIG MOUTH Lit Kit Routing
Maneuver the power ring terminal and in-line fuse through the rear of the indicated area into the fuse box.
Pop this clip if necessary, push the middle button down on the head of the clip to release

BIG MOUTH Lit Kit Power
Route the power wire along the rear of the fuse box as shown by the arrows and connect to the power terminal using the supplied M6 nut. Ensure the wire is not going to be pinched by the fuse box cover or subject to any kinks.
Zip tie through the back of the pop-up clip to secure the bundle
Zip tie the bundle of wire in the corner shown underneath the pop-up clip using 8″ zip tie.

Re-install Headlights

Phone App
Download the Diode Dynamics app and connect via Bluetooth.
How to connect to the app: 1. After installing the app from the app store, open the app on
your device. 2. Cycle the power to the Bluetooth controller by unplugging it
and plugging it back in or flick the power switch and wait a few seconds, then turn it back on. 3. Wait for the app to detect the controller, it will pop up on the app screen as a Bluetooth controller. If necessary, cycle the power once more to refresh the controller. 4. Once the controller shows up on the app, click it and connect. You have 30 seconds to select the controller once it shows up on the app. After 30 second you will need to refresh again to detect the controller again. 5. Note that if you mounted your controller behind a lot of metal components, this may degrade the signal and range.

Finalize
Re-install the bumper the same way it was removed and ENJOY!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>