Solight 1L67DZ Wireless Doorbell Instruction Manual
- July 21, 2024
- Solight
Table of Contents
Solight 1L67DZ Wireless Doorbell
Product Specifications
- Model: Solight 1L67,1L67B,1L67DT,1L67DZ series
- Operating Frequency: 433 – 433.92MHz
- Max. Operating Range: 200m in open area
- Battery Type: 3V CR2032
- Power Source: AC 230V
- Waterproof: Yes
- Maximum Pairing Options:
- One receiver (bell) can be paired with a maximum of 15 transmitters (buttons).
- One transmitter (button) can be paired with a maximum of 8 receivers (bells).
Product Usage Instructions
Inserting the Battery into the Transmitter
- Use a flat-blade screwdriver to push in on the latch and open the cover.
- Insert a 3V CR2032 battery, observing the marked polarities.
- Close the cover securely.
Transmitter and Receiver Location
- Before mounting the transmitter, ensure the doorbell works properly by plugging the receiver into the AC 230V socket.
- Press the button on the transmitter to test functionality.
- The transmitter is waterproof and can be placed outdoors if needed. Protect it from water and excessive heat.
Assigning a New Transmitter to a Receiver
- Plug the receiver into the power socket and hold the melody button for 3-4 seconds until the LED flashes quickly.
- Move the transmitter closer to the receiver and press it once to pair them.
Transmitter and Receiver Grouping Options
Receiver to Transmitter: One receiver can be paired with up to 15
transmitters.
Transmitter to Receiver: One transmitter can be paired with up to 8
receivers.
Troubleshooting
If the receiver fails to ring after pressing the transmitter button, check
for excessive distance and signal interference.
Contact your retailer for further assistance if needed.
FAQ
-
Q: How many transmitters can be paired with one receiver?
A: One receiver can be paired with a maximum of 15 transmitters. -
Q: What should I do if the receiver does not ring after pressing the transmitter button?
A: Check for excessive distance between the transmitter and receiver, and sources of signal interference. Contact your retailer if issues persist.
Dear Valued Customer, allow us to thank you for purchasing our product. Please read the following instructions carefully and follow them to ensure that your product serves you safely and to your full satisfaction. Avoid an incompetent manipulation with the device and always follow general principles of using electric appliances. Make sure to retain the present operating manual. Intended for household or indoor use. The product should only be used by adult persons. Never expose the receiver to environments with high humidity (such as bathroom), avoid contact with fluids.
Description
The doorbell operating frequency is 433 – 433.92MHz. The max. operating range is 200m in open area.
Inserting the battery into the transmitter
Use a flat-blade screwdriver to push in on the latch and open the cover. Insert a 3V CR2032 battery, observing the marked polarities. Then close the cover.
Transmitter and receiver location
Before mounting the transmitter, make sure that the doorbell works properly by plugging the receiver into the socket (AC 230V) where you want to use it and then pressing the button on the transmitter where you want to mount it. The transmitter is waterproof, it can be placed outdoors if necessary. However, prefer a place to protect the transmitter from water and excessive heat. The transmitter can be mounted on a base using a double-sided self-adhesive pad or screws with dowels, without or with a protective canopy:
Doorbell control
Select the melody using the button as shown above. Press the button to play
and change individual melodies. The selection is saved automatically.
Change volume with the volume change button as shown above. The volume level
changes from the lowest to the highest and back again, there is always one
beep.
The Pairing (The “Learning code”) function allows you to pair several bells or
buttons into one group, or to re-establish the connection between them. It is
possible to ring one bell with several buttons or to ring several bells with
one button. A maximum of 15 buttons can be paired with one bell. One button
can be paired with up to 8 bells.
Assigning a new transmitter to a receiver:
- Plug the receiver into the power socket. Press and hold the melody button for 3-4 seconds. The LED starts flashing quickly. Release the melody button and let the LED flash.
- Move the transmitter closer to the receiver and press once. The selected melody is played.
This assigns the transmitter to the receiver. The original transmitter is also assigned. Shown in Fig. 1 below. You proceed in a similar way when assigning a new receiver to one transmitter. All previously paired receivers are also assigned to the transmitter. Shown in Fig. 2 below.
Unpairing the buttons from the receiver, a reset of the connection:
If you have more than one transmitter paired to the receiver, you may need to
unpair one of the transmitters. It may also be that the wireless connection
has stopped working.
Perform the following steps:
- Unplug the receiver. Press and hold the melody button while plugging the receiver into the power socket. Keep the button pressed until the LED starts flashing quickly. Then release the button. The connection memory is cleared. The transmitters do not ring.
- Follow the previous paragraph – Assigning a new transmitter to a receiver. You are reconnected.
Transmitter and receiver grouping options
Troubleshooting
If the receiver fails to ring repeatedly after pushing the transmitter
button, check the following:
- excessive distance between the transmitter and the receiver.
- sources of strong signal interference (radio and wireless networks, large metal objects, reinforced concrete walls etc.) between the transmitter and the receiver.
In case of any difficulties please contact your retailer. A CE Declaration of
Conformity has been issued for the product in accordance with applicable
regulations. Available on website or upon request from the manufacturer:
info@solight.cz
Manufacturer: Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500
06, www.solight.cz
Solight Holding s.r.o. declares that the product complies with the
requirements and provisions of Directive 2014/53/EU. The device can be freely
operated in the EU. The Declaration of Conformity is available on
www.solight.cz. The product can be operated under
General Authorization No. VO-R/10/05.2014-3.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>