BRINK 616840 Wireless CO Sensor with 3 Position Switch Instruction Manual

: July 22, 2024
: BRINK

Table of Contents

BRINK 616840 Wireless CO Sensor with 3 Position Switch
Product Information
Product Usage Instructions
Description Wireless CO₂ sensor
Delivery content
Technical specification
Assembly
Setting to work
Information additional Wireless CO₂ sensor with 3-position switch
Settings
Signal amplifier
Troubleshooting and warranty
Maintenance
Declaration of Conformity
Recycling and disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRINK 616840 Wireless CO Sensor with 3 Position Switch

Specifications

Product: Wireless CO sensor with 3-position switch
Country: GB

Product Information

Description
The Wireless CO sensor with 3-position switch is designed to be used with a heat recovery unit (HRU) equipped with a USB connection and specific software versions as detailed below.

Technical Specifications

General product specification: HRU device software version starting with S2 Version S2.01.24 or higher, HRU device software version starting with S3 Version S3.01.03 or higher, Wireless transmitter/receiver and remote controller(s)/sensor(s) software version S1.01.15 or higher.
Environmental influences: Not specified.
Overview operational controls: The 3-position switch allows for different settings.

Product Usage Instructions

Assembly
To install the Wireless CO sensor with 3-position switch:

Follow the instructions for installing the sensor with the 3-position switch.
If needed, remove the sensor from its current location.
Optionally, use another frame for installation.

Setting to Work
To set up the sensor for operation:

Connect it with the wireless transmitter/receiver through pairing.
Perform a factory reset if required.
Pair multiple systems if needed.

Additional Information
To pair additional remote controllers/sensors, follow the provided instructions.

Settings
Adjust settings as needed for optimal performance.

FAQ

Q: Can the Wireless CO sensor with 3-position switch be used independently without a heat recovery unit?
A: No, the sensor should only be used in combination with HRUs meeting specific software version requirements.

Store near the appliance

This appliance may be used by children as of 8 years of age, persons with reduced physical or mental capacities, and persons with limited knowledge and experience if they are supervised or have received instructions on how to use the appliance safely and are aware of the possible dangers.
Children younger than 3 years of age must be kept away from the appliance, unless they are under constant supervision.
Children between the ages of 3 and 8 may switch the appliance on or off, but only if supervised or if they have received clear instructions on the safe use of the appliance and understand the possible dangers, on the condition that the appliance has been placed and installed in the normal position for use. Children between the ages of 3 and 8 may not insert the plug into the socket, nor clean or make changes to the settings of the appliance, nor carry out any maintenance on the appliance that would normally be carried out by the user. Children may not play with the appliance.
If you need a new power cable, always order the replacement from Brink Climate Systems B.V. To prevent dangerous situations, a damaged mains connection must only be replaced by a qualified expert!

User manual

Dear client,
Thank you for purchasing the Wireless CO₂ sensor. This user and installation manual contains all required information to quickly become familiar with the product. We kindly request you to carefully go through this information before using the product. This user’s manual is intended for the Wireless CO₂ sensor installer and end user.
Store this user’s manual. For more information or ordering manuals, please contact:
Brink Climate Systems B.V.
P.O .Box 11
NL-7950 AA, Staphorst, The Netherlands
T: +31 (0) 522 46 99 44
F. +31 (0) 522 46 94 00
E. info@brinkclimatesystems.nl
www.brinkclimatesystems.nl

Description Wireless CO₂ sensor

Intended and unintended use
This manual is about the Wireless CO₂ sensor (See D in the image below).
The Wireless CO₂ sensor should only be used in combination with products approved by Brink Climate Systems B.V..
The Wireless CO₂ sensor can only be used with a heat recovery unit (HRU) equipped with a USB connection and where the various components are equipped with specific software versions:
- HRU device software version starting with S2 → Version S2.01.24 or higher.
- HRU device software version starting with S3 → Version S3.01.03 or higher.
- Wireless transmitter/receiver and remote controller(s)/sensor(s) software version → S1.01.15 or higher.
Software versions on the HRU device can be checked through the user interface or by consulting the relevant installation manual of the device. The HRU device can be updated using the USB stick and instructions provided with the wireless transmitter/receiver.
Brink Climate Systems B.V. offers a series of remote controllers/sensors that connect to a heat recovery unit (HRU) via a wireless transmitter/receiver (F). This series consists of 5 types of wireless remote controllers/sensors (A-E). The remote controller (A, B, or C) indicates when the filter(s) need to be replaced/cleaned or when there is a malfunction in the ventilation system.
Optionally, a signal amplifier is available. This amplifier is necessary when the signal in the dwelling/house needs to travel a long distance, in very well-insulated homes, or in situations where signal-disruptive materials are used. When designing, provide for provision for this signal booster.
The connected HRU device is operated by pressing one of the buttons on the Wireless CO₂ sensor. For explanation of the buttons of the Wireless CO₂ sensor see → Overview operational controls -> page 10.
The Wireless CO₂ sensor must always be used together with a Wireless transmitter/receiver on the HRU appliance; a combination of multiple remote controller(s)/sensor(s) on 1 Wireless transmitter/receiver is possible.
In total, a maximum combination of 12 remote controller(s)/sensor(s) can be paired to 1 transceiver (Max. 4 controllers / max. 4 CO2-sensors and max 4 humidity sensors).
- Note
- A remote controller with a build in CO2-sensor is seen by the connected HRU appliance as a CO2-sensor and a controller with a build-in humidity sensor is seen as a humidity sensor(RH).
If one or more CO2 sensors are paired with the HRU device, then the device ventilates according to the conditions set in the HRU device by the connected CO2 sensor(s).
If multiple sensors are used, the sensor requesting the highest ventilation level takes priority; if multiple remote controllers are used, the most recently used ventilation level takes precedence.
When the vacation mode ( ) is activated (if available), the humidity control/CO2 control (if applicable) is not operational! The CO2 control is also not operational in setting 3 of a 3-position switch and in boost mode on a RH sensor with boost function.
The airflow rates associated with the ventilation settings must always be set in the paired HRU device. Refer to the installation manual of the connected HRU device for the ventilation settings.
A. Wireless 3-position switch
B. Wireless CO2 sensor with 3-position switch
C. Wireless RH sensor with boost function
D. Wireless CO2 sensor
E. Wireless RH sensor
F. Wireless transmitter/receiver
G. Device with USB connection (e.g., HRU device type Flair)

Delivery content

Check that the delivered Wireless CO₂ sensor is complete and not damaged.
The delivery content of the Wireless CO₂ sensor consists of the following components:

Wireless CO₂ sensor
Frame
Wall bracket
Mounting screws
Permanent power supply (230 VAC/5 VDC)
Short information with QR-code to on line manual

Technical specification

General product specification

Product description
Name: Wireless CO₂ sensor with 3-position switch
Technical product specifications
Operating voltage 5 V
Protection class IP21
Frequency 868 MHz
Color RAL 9010 (White)
Ambient conditions
Ambient temperature 0 °C to 50 °C
Storage temperature -20 °C to 60 °C
Humidity 0% to 90%
Other For indoor use only
Range 300 m (open field; 1 meter hight

Environmental influences

For correct functioning, the Wireless CO₂ sensor should be placed and used in a space with the correct ambient conditions for proper operation. The Wireless CO₂ sensor may only be mounted indoors, but not close to a heat source, a radiator or in a extreme humid environment. The Wireless CO₂ sensor may not be exposed to direct radiation heat (sun light). The Wireless CO₂ sensor may not be installed close to a magnetic field. This could damage internal components.
Overview operational controls
The Wireless CO₂ sensor has four invisible (capacitive) buttons. Each button is equipped with a LED (white).

Button ventilation level 1 or automatic ventilation position in accordance with CO2 sensor(s)
Button ventilation level 2
Button ventilation level 3
Button boost function
Button holiday mode
Filter/fault indication LED (red)

Button 1 (auto)
When button 1 is operated, the HRU appliance will be set to ventilation level 1 (basic ventilation during absence) or the HRU appliance will ventilate automatically conform set requirements of the connected CO2 sensor(s); the white LED next to button 1 will flash once as “button press” confirmation.
Button 2
When button 2 (sufficient ventilation during presence) is operated, the HRU appliance will be set to ventilation level 2; the white LED placed next to button 2 will flash once as “button press” confirmation.
Button 3
When button 3 (maximum ventilation during cooking/showering) is operated, the HRU appliance will be set to ventilation level 3; the white LED placed next to button 3 will flash once as “button press” confirmation
Button 4/ Boost ( )
When button 4 is operated, the HRU appliance will run for 30 minutes at ventilation level 3 (boost function) and then return to the previous ventilation position; the white LED placed next to button 4 will flash once as “button press” confirmation.
Button 5 ( )
When button 5 (minimum ventilation) is operated, the HRU appliance will be set to ventilation level 0 (holiday position); the white LED next to button 5 will blink once as “button press” confirmation.
Filter/ fault LED
This red LED indicates when filter (s) must be cleaned / replaced or when a malfunction has occurred in the connected HRU appliance.

Filter notification

The filter(s) in the HRU device connected to the Wireless CO₂ sensor with 3-position switch must be cleaned or replaced when the red LED on the Wireless CO₂ sensor with 3-position switch lights up.
For battery-powered Wireless CO₂ sensor with 3-position switch: LED lights up for 300 seconds when any button is pressed (Wireless CO₂ sensor with 3-position switch with battery power).
For mains-powered Wireless CO₂ sensor with 3-position switch (optional): LED lights up continuously.
The filter notification cannot be reset via the Wireless CO₂ sensor with 3-position switch. Refer to the manual of the HRU device connected to the Wireless CO₂ sensor with 3-position switch for resetting the filter notification.

Fault notification

If there is a fault in the HRU appliance connected to the Wireless CO₂ sensor with 3-position switch, the red LED on the Wireless CO₂ sensor with 3-position switch flashes with frequency of 1 Hz (1 blink per second).
For battery-powered Wireless CO₂ sensor with 3-position switch: LED flashes for 300 seconds when any button is pressed (Wireless CO₂ sensor with 3-position switch with battery power).
For mains-powered Wireless CO₂ sensor with 3-position switch (optional): LED flashes continuously.
Check the installation instructions of the HRU appliance connected to the Wireless CO₂ sensor with 3-position switch for troubleshooting for the error notifications indicated on the Wireless CO₂ sensor with 3-position switch.

Lost connection

When the Wireless CO₂ sensor with 3-position switch loses connection with the Wireless transmitter/receiver, the fault LED will also flash.
The LED flashes 3 times 0.5 seconds ON and 60 seconds OFF or flashes for 300 seconds if any of the buttons are operated (Wireless CO₂ sensor with 3-position switch with battery power supply).
Filter and fault notifications are overruled.

Assembly

Installing Wireless CO₂ sensor with 3-position switch

Perform step1 to step 5 to install the Wireless CO₂ sensor.
An example of a wireless 3-position switch is shown in this section, but the Wireless CO₂ sensor is installed in the same way.
The Wireless CO₂ sensor needs to be installed on a flush mounted electrical wall box (Ø 55 mm).

Danger
At all times disconnect the 230 V mains supply when connecting the permanent power supply!

Step 1

Place the permanent power supply (A) in the wall box.
Connect the 230V mains supply to the factory mounted gray connectors of the power supply. Strip the wire over a length of approx. 7 mm.

Step 2

Feed the red and black wires with the green connector through the square hole in the in the wall bracket(C).
Screw the wall bracket on the wall box.
- Note
  The arrow on the wall bracket must point upwards!

Step 3

Feed the red and black wire with the green connector through the frame (B), and connect this to the connector on the back side of the Wireless CO₂ sensor (A).
Click the Wireless CO₂ sensor (A) together with connected red and black wires and the frame (B) on the wall bracket (C).

Step 4

After mounting the Wireless CO₂ sensor on the wall bracket, remove the foil from the front.
Reconnect the 230 V. mains supply.
Step 5
When the Wireless CO₂ sensor has been installed on the wall, the Wireless transmitter/receiver* can be placed in the USB port of the HRU appliance that needs to be connected with the Wireless CO₂ sensor. To connect the Wireless transmitter/receiver with HRU appliance see → Connecting with wireless transmitter/receiver B(Pairing) -> page 14
The Wireless transmitter/receiver is not included in the scope of delivery of the Wireless CO₂ sensor and must be ordered separately!
Note
Once the wireless remote control/sensor receives power, all 5 LEDs on the remote control/sensor will start blinking.

Remove Wireless CO₂ sensor with 3-position switch

For removing the Wireless CO₂ sensor from the wall bracket: Grasp the front of the Wireless CO₂ sensor by the edges and gently pull it away from the bracket.
An example of a wireless 3 position switch is shown in this section, but other wireless controllers/sensors are to be removed from the wall bracket in the same way.

Using another frame (option)

The Wireless CO₂ sensor consists of a wall bracket (C), a frame (B) and the wireless controller (A). The wall bracket (C) is designed in such a way that a large number of frames from other vendors can be used.
Products are supplied with Brink frame as standard. This frame can be replaced by frames from the other manufacturers and series. Appearance and tolerances vary by manufacturer. The following types of frames can be used instead of the standard frame:
- A. Gira – System 55
- B. Busch Jaeger Balance/Reflex SI
- C. Jung AS
- D. Siemens Delta
- E. Berker S.1
- F. Marten System M $BRINK-CO2-Wireless-CO-sensor- $12$$
The above mentioned alternative frames are not included in the Brink delivery program! $BRINK-CO2-Wireless-CO-sensor- $13$$

Setting to work

Connecting with wireless transmitter/receiver (Pairing)

When the Wireless CO₂ sensor is installed and the Wireless transmitter/receiver is placed in the HRU appliance (see image on the right), the two can be connected (pairing).
For a HRU appliance equipped with a display, the USB symbol ( ) is visible as confirmation that the Wireless transmitter/receiver has been “recognised”; for a HRU appliance without a display, this
USB symbol will be visible in the app. If the USB symbol is not visible, your HRU appliance is probably equipped with a software version before July 2022 and it is not possible to connect the Wireless CO₂ sensor.
Follow the steps as described below:
Step 1
- Apply mains to the HRU appliance.
Step 2
- Press and hold the pairing button of the USB transceiver between 3 and 10 seconds.
- The green LED on the USB transceiver starts flashing (1x per second).
- The pairing mode will be active for 10 minutes. $BRINK-CO2-Wireless-CO-sensor- $15$$
Step 3
- Press and hold the pairing button between 3 seconds 10 seconds on the bottom of the controller (through a small hole), for example with the end of a paper clip. When pressing the button a ”click” should be noticeable.
Pairing is enabled when four Led lights illuminate in turn (0.5 sec ON, the next one comes on when the previous one is off).
Pairing is disabled when Filter/service LED is ON for two seconds; go back to step 3.
If pairing fails, reset the Wireless CO₂ sensor to factory settings and try pairing again. Or see → Signal amplifier -> page 21

Step 4

Choose under which number the Wireless CO₂ sensor should be registered by configuring a “NODE ID”; press any of the four buttons on the Wireless CO₂ sensor (do not use the holiday button ). For example press button 2; LED 2 will flash once.
When pairing multiple sensors/remote controllers with the HRU device, press a button for NODE ID that has not been paired yet. This ID must be unique for each sensor. The button number corresponds to the number of the paired accessory in the HRU device menu.
If pairing is unsuccessful, return to step 3. Also, check the wireless transmitter/receiver.
To stop the pairing mode: Briefly press and hold the pairing button of the wireless transmitter/receiver (1 second). The green LED on the wireless transmitter/receiver will stop flashing.
For settings of the CO2-sensor(s) see → Settings -> page 19
Note
Always deactivate the pairing mode on the wireless transmitter/receiver immediately after pairing.
Note
If a wireless remote controller/sensor is registered with an existing NODE ID, the first registered remote controller/sensor will be overwritten. Please ensure that all paired remote controllers/sensors have their own unique NODE ID.
- The activation of the remote controller/sensor and the airflow rates associated with the ventilation settings must always be set on the paired HRU device. This cannot be done on the Wireless CO₂ sensor.
  Refer to the installation manual of the connected HRU device for further instructions.

Factory rese t Wireless CO₂ sensor with 3-position switch

It is possible to reset the wireless transmitter/receiver and remote controller(s)/sensor(s) back to factory settings:

Factory resetting Wireless CO₂ sensor with 3-position switch
- Press the pairing button (for example with end of a paperclip) for more than 20 seconds. When the pairing button is properly pressed , one feels a “click”.
- To confirm this reset all 5 LED’s will flash two times (0,5 second on and 5 seconds off).
- All the pairing information has been deleted from the Wireless CO₂ sensor.

Factory resetting USB transceiver

Press the button on the Wireless transmitter/receiver for more than 20 seconds.
To confirm this reset, the green LED on the Wireless transmitter/receiver will flash two times.
All the pairing information has been deleted from the Wireless transmitter/receiver.

Pairing multiple systems

When pairing multiple installations/residences, be sure to complete the pairing of the wireless transmitters per installation/residence, and ensure that only one (1) wireless transmitter/receiver is in pairing mode at a time. It is possible for a Wireless transmitter/receiver in pairing mode to detect and pair with wireless transmitter/receiver(s), wireless controller(s), and/or sensor(s) from different installations/residences.
To stop the pairing mode on a Wireless transmitter/receiver: Press the pairing button on the wireless transmitter/receiver (1 second). The Green LED on the device will stop flashing.
Note
Always deactivate the pairing mode on the wireless transmitter/receiver immediately after pairing.

Information additional Wireless CO₂ sensor with 3-position switch

Pairing additional remote controller/sensor
For connecting extra remote controllers or sensors to the HRU appliance follow the steps as described below.
A wireless 3-position switch is shown as an example.

Step 1
Apply mains power to the HRU appliance.
Step 2
Press and hold the pairing button on the Wireless transmitter/receiver (between 3 and 10 seconds).
The green LED on the Wireless transmitter/receiver starts flashing (1x per second). The pairing mode is active for 10 minutes.
Step 3
Press and hold the pairing button between 3 seconds 10 seconds on the bottom of the controller (through a small hole), for example with the end of a paper clip. When pressing the button a ”click” should be noticeable.
Pairing is enabled when four Led lights illuminate in turn (0.5 sec ON, the next one comes on when the previous one is off).
- ```
* Pairing disabled when the red LED is ON for two seconds.  
```
  If pairing fails, reset Wireless CO₂ sensor to factory setting and try to pair Wireless CO₂ sensor again. Or see → Signal amplifier -> page 21
Step 4
- Choose under which number the sensor should be registered by configuring a “NODE ID”; press any of the four buttons on the Wireless CO₂ sensor (do not use the holiday button ). For example press button 2; LED 2 will flash once.
- When pairing multiple sensors/remote controllers with the HRU device, press a button for NODE ID that has not been paired yet. This ID must be unique for each sensor. The button number corresponds to the number of the paired accessory in the HRU device menu.
- If pairing is unsuccessful, return to step 3. Also, check the wireless transmitter/receiver.
- To stop the pairing mode: Briefly press and hold the pairing button of the wireless transmitter/receiver (1 second). The green LED on the wireless transmitter/receiver will stop flashing.
- Note
  Always deactivate the pairing mode on the wireless transmitter/receiver immediately after pairing.
- Note
  If a wireless remote controller/sensor is registered with an existing NODE ID, the first registered remote controller/sensor will be overwritten. Please ensure that all paired remote controllers/sensors have their own unique NODE ID.

Settings

Wireless CO₂ sensor functioning general
The Wireless CO₂ sensor(es) ensure optimum ventilation in the dwelling by automatically adjusting the air flow rate on the basis of the CO2 level. When multiple Wireless CO₂ sensors are installed the air flow rate is determined by the Wireless CO₂ sensor that requests the highest level.
Depending on the minimum and maximum (set) PPM value, the Wireless CO₂ sensor adjusts the air flow proportionally between the setting 1 (set low) and setting 3 (set high)
- Note
  The CO2 control is only active when the HRU appliance is in ventilation mode 1 or 2.
- 1 = Air flow rate
- 2 = Amount of CO2 in area where Wireless CO₂ sensor is situated
- Q Min = Minimum air flow setting 1
- For example Wireless CO₂ sensor factory setting step no. 1.2 (in Flair appliance) = 100 m3/h
- Q Max = Maximum air flow setting 3
- For example Wireless CO₂ sensor factory setting step no. 1.4 (in Flair appliance) = 250 m3/h
- Min. PPM = Minimum (set) PPM value
- For example Wireless CO₂ sensor factory setting step no. 6.2 (in Flair appliance) = 400 PPM
- Max. PPM = Maximum (set) PPM value
- For example Wireless CO₂ sensor factory setting step no. 6.3 (in Flair appliance) = 1200 PPM

Wireless CO₂ sensor with 3-position switch settings
To activate the connected Wireless CO₂ sensor, the setting of the Wireless CO₂ sensor must be set to “ON” in the settings menu of the relevant HRU appliance. To change settings in the settings menu, see the installation instructions for the appliance in question. When desired, the minimum and maximum PPM values on which the Wireless CO₂ sensor are controlled can also be set in the settings menu.

CO 2- settings at Flair appliance

400 – 1200

|

25

6.3| Maximum PPM Wireless CO₂ sensor 1| 1200
6.4| Minimum PPM Wireless CO₂ sensor 2| 400
6.5| Maximum PPM Wireless CO₂ sensor 2| 1200
6.6| Minimum PPM Wireless CO₂ sensor 3| 400
6.7| Maximum PPM Wireless CO₂ sensor 3| 1200
6.8| Minimum PPM Wireless CO₂ sensor 4| 400
6.9| Maximum PPM Wireless CO₂ sensor 4| 1200

CO₂ values check on ventilation appliance
In the information menu (for all Flair appliances) the values of the connected Wireless CO₂ sensor(es) can be read out. With this you can also check the proper operation of the connected Wireless CO₂ sensor(es). Values can only be read in this information menu; changing of settings is not possible. For more information regarding the information menu, see the installation instructions for the appliance in question.

Information menu at Flair appliances:
Press the info button on the display ∧ and ∨ use the and button go to the reading values of the Wireless CO₂ sensor(es).
You can consult the user interface or the display of the HRU appliance device to see which remote controller/ sensor the HRU Appliance controls.

Note
It may take up to 48 hours for the Wireless CO₂ sensor to measure and display the correct value.

Signal amplifier

An optional signal amplifier is available. This amplifier is necessary when the signal needs to cover a long distance in the house , in very well-insulated homes, or in situations where signal-disrupting materials are used.
If a sensor/remote controller is out of range of the wireless transmitter/receiver and cannot be paired (red LED on controller or sensor); remove the wireless transmitter/receiver from the Brink device and connect it to a smartphone adapter or laptop (to provide power to the wireless transmitter/receiver). Now locate the wireless transmitter/receiver in the same room as the controller or sensor to be paired.
Restart the pairing procedure. If pairing is successful, a signal amplifier needs to be installed to extend the signal range of the wireless transmitter/receiver to the location of the controllers and/or sensors.
The signal amplifier can be ordered at Brink under article code 532715.
Note
The signal amplifier requires a fixed 230 V power supply.
Note
Always pair remote controllers and sensors directly to the wireless transmitter/receiver and not through the signal amplifier. The signal amplifier cannot be used for pairing.
A. Wireless 3-position switch
B. Wireless CO2 sensor with 3-position switch
C. Wireless RH sensor with boost function
D. Wireless CO2 sensor
E. Wireless RH sensor
F. Wireless transmitter/receiver
G. Device with USB connection (e.g., HRU device type Flair)
H. (Optional) Signal amplifier

Troubleshooting and warranty

Failure
- When using battery-powered remote controllers/sensors, the HRU device will go into a fault state when the battery is low. The fault will disappear automatically after replacing the battery.
- Check if the HRU device is in vacation mode if wireless CO2 or RH sensors are not functioning.
- If there are issues with pairing, see → Signal amplifier -> page 21
- Refer to the installation manual of the connected HRU device for other errors.
Warranty
- “The Wireless CO₂ sensor has been carefully manufactured by Brink Climate Systems B.V. and meets high-quality standards. The functionality of the Wireless CO₂ sensor is guaranteed for a period of two years from the moment of delivery. This warranty is provided in accordance with Brink Climate Systems B.V.’s General Terms and Conditions, which you can find on www.brinkclimatesystems.nl. In case of incorrect or improper use of the Wireless CO₂ sensor and failure to follow the instructions in this user manual, your right to warranty is void.
- If you wish to claim warranty:
- You must make this known in writing via:
- Brink Climate Systems B.V.
- P.O .Box 11
- NL-7950 AA, Staphorst, The Netherlands
- Note
  It is not allowed to make any changes to the hardware or software of the Wireless CO₂ sensor. This can affect the proper functioning of the Wireless CO₂ sensor, and in that case, all warranties will be void.”

Maintenance

Maintenance
Clean the Wireless CO₂ sensor regularly with a soft cloth.
- Note
  Never apply water and/or (cleaning) liquid to the Wireless CO₂ sensor.

Declaration of Conformity

This declaration of conformity is issued under the sole responsibility of the manufacturer.
Manufacturer: Brink Climate Systems B.V.
Address: P.O. Box 11 NL-7950 AA, Staphorst, The Netherlands
Product: Wireless CO₂ sensor with 3-position switch
The product described above complies with the following directives:
- 2014/53/EU (EMC directive)

The product described above has been tested according to the following standards:

EN 301 489-3: V2.1.1:2019-03
EN 300 220-2: V3.2.1:2018-06
ETSI EN 300 220-1: V3.1.1 (2017-02)
EN 62479: 2010
EN 60669-2-5: 2016
EN 60669-2-1: 2004 + A1:2009
EN 50428: 2005 + A1:2007 + A2:2009
EU-Type Examination Certificate 40056587; VDE Testing and Certification Institute (0366).
Staphorst, 15-04-2023
A. Hans
Managing Director

Recycling and disposal

Do not dispose of as household waste!

In accordance with the Waste Disposal Act, the following components must be disposed of or recycled in an environmentally compatible manner by means of appropriate collection points:
- Old appliance
- Wearing parts
- Defective components
- Electrical or electronic waste
- Environmentally hazardous liquids and oils

Environmentally compatible means separated by material groups to ensure the greatest possible recyclability of the basic materials with the minimum environmental impact.

Dispose of packaging made of cardboard, recyclable plastics and synthetic filler materials in an environmentally compatible manner through appropriate recycling systems or a recycling centre.
Please observe the applicable national and local regulations.

Brink Climate Systems B.V.