BRINK Flair 400 Electric Pre and Post Heater Instruction Manual

BRINK Flair 400 Electric Pre and Post Heater

Flair post- and preheater

The Flair post heater and the Flair preheater are identical to each other and electrically connected to the Flair appliance in the same way.

Flair 200/225

• A = Ø160 mm with a reduction to DN125
• B = 350 mm

Flair 300/325

• A = Ø160
• B = 400 mm

Flair 400

• A = Ø180
• B = 400 mm

Flair 450/600

• A = Ø180 with enlargement to DN200
• B = 400 mm

• C1 = Brown
• C2 = Bleu
• C3 = Green/yellow
• C4 = Black
• C5 = White

1. Heating coil
2. PCB type UVP1
3. Temperature sensor
4. Maximum safety with manual reset temperature sensor
5. Red LED; lights up when the heater is connected to the Flair appliance
6. 2-pole eBus connection X17 on Flair appliance
7. Power plug 230V
8. Dipswitch

By setting dipswitches on the PCB in the heater, the Flair appliance recognizes the connected heater. This Flair heater must always be mounted directly on the connection of the Flair appliance. After installation of the heater, the setting values of the Flair appliance must always be adjusted; for procedure adjustment settings Flair post-and preheater in the setting menu of the Flair appliance, see the corresponding Flair installation instructions.

Setting the correct dipswitch setting

At the factory the post- and preheater are supplied with all dipswitches set to “OFF”; the correct dipswitch setting must always be set by the installer.

Note: If the setting is incorrect, the heater will not function or will function incorrectly!

1. Factory setting
2. Dipswitch setting preheater
3. Dipswitch setting post heater

Mounting position

Both the post- and preheater are always placed on the Flair appliance in the same way. The heating coil is always between the Flair appliance and the temperature sensor in the heater! The Flair post- and preheater can be mounted both horizontally and vertically. For horizontal mounting, always mount the connection box upwards for proper functioning of the temperature sensor!

Flair post heater

1. Flair appliance left version
2. Flair appliance right version

Flair preheater

1. Flair appliance left version
2. Flair appliance right version

Connection

A Connection Flair post heater with Flair appliance

1. Heating coil
2. Maximum safety with manual reset
3. 2-pole eBus connection X17 on Flair appliance
4. Temperature sensor
5. PCB type UVP1
6. Airflow direction
7. Dipswitch setting Flair post heater

• C1 = brown
• C2 = blue
• C3 = green/yellow
• C4 = black
• C5 = white

B Connecting Flair preheater with Flair appliance

1. Heating coil
2. Maximum safety with manual reset
3. 2-pole eBus connection X17 on Flair appliance
4. Temperature sensor
5. PCB type UVP1
6. Airflow direction
7. Dipswitch setting Flair preheater

• C1 =brown
• C2 = blue
• C3 = green/yellow
• C4 = black
• C5 = white

Setting step number in Flair appliance

When a Flair post- and/or preheater is placed on a Flair appliance, this must always be set in the setting menu of the Flair appliance!

For procedure adjustment settings in this set menu ****of the Flair appliance, see the corresponding Flair installation instructions.

• https://www.brinkclimatesystems.nl/support/downloads.

When setting a preheater, set parameter 5.1 to ON; if a post heater is used, parameter 5.2 must be set to ON and, if required, the post heater temperature can still be set in parameter 5.3.

Preheater

Step No.| Description| Factory setting| Adjusting range
5.1| Preheater ON and OFF| OFF| ON/ OFF
Postheater
Step No.| Description| Factory setting| Adjusting range
5.2| Postheater ON and OFF| OFF| ON/ OFF
5.3| Temperature postheater| 21 °C| 15,0 °C – 30,0 °C

Fault

In the event of a fault in the Flair post-or preheater, a fault message will be visible on the display of the Flair appliance. A LED is mounted on the PCB of the Flair pre- and post-heater (for position LED see number 5 ® 1 Flair post-and preheater page 2). This LED flashes when the eBus connection has not yet been established. When the connection is established, the LED stops flashing. This startup can sometimes take a few minutes.

Error codes preheater

Error No.| Description
E171/ E2700| General Error
E171/ E2701| Preheater – connection lost
E171/ E2702| Preheater – sensor error
E171/ E2703| Preheater – element error
Error codes postheater

Error No.| Description
E172/ E2800| General Error
E172/ E2801| Postheater – connection lost
E172/ E2802| Postheater – sensor error
E172/ E2803| Postheater – element error

Technical information and service

Technical information Flair post- and preheater

Supply voltage| 230 V / 50 Hz|  |  |
Rated current| 4,5 A|  |  |
Rated power| 1000 W|  |  |
Protection degree| IP20|  |  |
For use with| Flair 200/225| Flair 300/325| Flair 400| Flair 450/600
Heater art.no.| 310689| 310690| 310692| 310699
Duct diameter| Ø 125 mm| Ø 160 mm| Ø 180 mm| Ø 200 mm
Length heater| 350 mm| 400 mm| 400 mm| 400 mm
Total length| 540 mm| 400 mm| 400 mm| 530 mm
Total weight| 4,6 kg| 3,0 kg| 3,0 kg| 4,0 kg

For more information see the Flair installation instructions.

• https://www.brinkclimatesystems.nl/support/downloads.

Brink Climate Systems B.V.
P.O. Box 11, NL-7950AA Staphorst T: +31 (0) 522 46 99 44
E: info@brinkclimatesystems.nl.
W: www.brinkclimatesystems.nl.

References

• art.no
• Brink Climate Systems - Breathe Excellence, Flourish in Life
• Brink | Downloads

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>