LUTRON QSFC-J-EDU-R2 Smart Blinds and Shades User Guide

: July 22, 2024
: Lutron

Table of Contents

Roman Shade
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Roman Shade

Battery Powered Window Shade • Setup and Operation Guide

1 Assigning a control:

The shade features a single “Shade Button” with an LED which is used to activate and indicate various steps while assigning and programming the shade for compatible handheld remote control.

Shade Button with LED

NOTE: If the Lutron Smart Bridge is installed, use the Lutron App to program and control the shade.

Compatible Controls (sold separately)

Pico wireless control

Open
Raise
Close
Preset
Lower

Lutron 4-Group RF remote control

Open
Close
Shade Groups
Raise
Lower
Preset
All Shade Groups

1.2 Assign a Pico Wireless Control

a. Tap the Shade Button. A small screwdriver or stylus is required.

b. The Shade Button lights.

c. Press and hold the Close button.

d. The Shade Button flashes. Assignment is complete.

e. Repeat for additional assignments.

1.3 Assign a Lutron 4-Group RF Remote Control

a. Tap the Shade Button. A small screwdriver or stylus is required.

b. The Shade Button lights.

c. Choose a Shade Group button. Press and hold.

d. The Shade Button flashes. Assignment is complete.

e. Repeat for additional assignments.

2 Adjusting shade limits (OPTIONAL):

The shade’s upper and lower limits are pre-programmed based on the window dimensions and mounting option. If adjustment is needed, follow these steps:

a. Tap the Shade Button. A small screwdriver or stylus is required.

b. The Shade Button lights.

c. Press and hold the Open and Raise Buttons.

d. The Shade Button flashes, then stays on.

e. Use the Raise and Lower Buttons to position the shade at the preferred upper or lower limit.

f. SET UPPER LIMIT
With the shade at the preferred upper limit, press and hold the Open Button.

OR

SET LOWER LIMIT
With the shade at the preferred lower limit, press and hold the Close Button.

g. The Shade Button flashes. Limit set is complete.

Serena Setup & Operation

3 Setting a Favorite Level (OPTIONAL):

The favorite level is factory programmed to the midpoint between the shade limits.

NOTE: When setting differing favorite levels among multiple shades assigned to the same control, disconnect power to the shades you do not want affected by removing one battery from each.

a. Use the Raise and Lower Buttons to position the shade at the desired favorite level.

b. Press and hold the Favorite Button.

c. The Shade Button flashes. Favorite level is set.

Restoring factory default settings:

A Serena Roman Shade

NOTE: Restoring a Serena Roman Shade to its factory default settings will remove all control assignments and favorite programming. Upper and lower limits are retained.

Tap the Shade Button quickly three times, and hold the Shade Button after the third tap until the Shade Button LED blinks GREEN rapidly.
Immediately tap the Shade Button quickly three more times, until the Shade Button LED blinks GREEN rapidly, then blinks RED-then-GREEN three times, and turns off.

B Pico Wireless Control*

Triple tap and hold either the Top or Bottom button on a Pico wireless control. DO NOT release the button after the third tap.
Keep the button pressed on the third tap until the LED next to the top button turns on solid (approx. 3 seconds).
Immediately release the button and triple tap it again. The LED next to the top button will flash quickly. When the LED stops flashing, reset is complete.

C Lutron 4-Group RF Remote Control*

Tap the All Shade Groups button.
Triple tap and hold the Open or Close button. DO NOT release the button after the third tap. The All Shade Groups button LED will light and stay on for approximately 3 – 5 seconds.
Keep the button pressed until the All Shade Groups button LED turns off.
Immediately release the button and triple tap it again. The LED’s of Shade Group buttons 1 – 4, and the All Shade Groups button will light and stay on for approximately 3 – 5 seconds. When all LED’s turn off, the control has been restored to factory default settings.

*NOTE: Restoring factory default settings will remove all shade assignments and favorite programming.

FCC Information

drive model: QSFC-J-EDU-R2
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.

IC Information

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject tot he following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

Shade drive models:

QSFC-J-EDU-R2 6-12 V⎓ 5 W 431 MHz – 437 MHz

Worldwide Headquarters | USA
Lutron Electronics Co., Inc.
7200 Suter Road, Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800 • FAX: 1.610.282.3090
Technical Support: 1.800.523.9466
Toll Free: 1.888.LUTRON1
Email: shadinginfo@lutron.com
Online: www.lutron.com/shadingsolutions

For complete warranty information, please see:lutron.com/TechnicalDocumentLibrary/Window SystemsWarranty.pdf

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

05/2024
P/N 045977 Rev. A

Lutron, the Lutron logo, Serena, and Pico are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and/or other countries.