mifa WildRod Portable Bluetooth Speaker Wireless Outdoor User Guide
- June 9, 2024
- MiFa
Table of Contents
mifa WildRod Portable Bluetooth Speaker Wireless Outdoor
POWER ON
PACKING CONTENTS
- Speaker 1pc
- Typc-C charging cable 1pc
- Quick manual lpc
- Safety Warning 1pc
BLUETOOTH CONNECTION
Note: Two smart devices can be connected at the same time.
MODE SWITCH
PLAY
LIGHT
PARTY ADD
- Connect Wild Rod with your smart phone and laptop and then play music, then it becomes the master speaker.
- Short press the button of the master speaker and other speaker to enter PartyAdd mode, the white indicatorwill always on and the music will be played simultaneously after Connected successfully.
Tips: Short press button to exit from the PARTYADD mode.
TWS
-
Press and hold the button of two speakers,there will be a sound “TWS connected” to indicate pairing is complete.
-
When the connection is successful, the white indicator of the master speaker is breathing, the indicator of the slave speaker is always on.
(The master speaker is the left channel the slave one is the right channel.) -
Short press the button of either speaker to disconnect from TWS once they paired successfully.
CHARGE
Technical Specification
- Speaker: Woofer, 45 x 80mm, Tweeter dD20mm
- Passive Radiators: 68mmx 2pcs
- Output power: 20W RMS Woofer, 10W RMS Tweeter
- Frequency response: 65Hz-20kHz
- SNR: >80dB
- Battery type: Lithium battery (3.7V 2500mAh) x 2
- Charging interface: USBType-C
- Charging time of battery: Approx.2.5 hours (5V/3A)
- Music playing time: Approx.12 hours (depending on volume and audio content, with dynamic light off)
- Bluetooth version: 5.3
- Playable format: MP3, WMA, WAC, FLAC, APE (MicroSD Card)
- Protection function: IP67 dust-proof and moisture-proof
- Floatable: Yes
- Dynamic light: RGB ambient lighting
- Dimension of product: W190mm* H75mm D75mm/W7.48″ xH 2.952″ x D2.952″
- Weight of product: 0.63kg
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction FCC ID :2AXOX-WILDROD
MIFA INNOVATIONS LLC
- www.mifa.net
- Designed in US
- Made in China Copyright © MIFA. All rights reserved.
- MIFA, the MIFA logo and other MIFA marks are all owned and registered by MIFA
- INNOVATIONS LLC. All other trademarks are the property of their respective owners.
- The information contained here is subject to change without prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>