SEALEY MS0630 Motorcycle Rear Wheel Side Stand Type Dolly User Manual

SEALEY MS0630 Motorcycle Rear Wheel Side Stand Type Dolly

Product Information

Specifications

• Model No: MS0630
• Capacity: Max. Dolly Load: 300kg / Max. Motorcycle Weight: 500kg
• Loading Track Dimensions (L x W x H): 550 x 250 x 120mm
• Overall Dimensions (L x W x H): 1300 x 650 x 120mm

Product Usage Instructions

Safety

• Maintain the dolly in good condition using an authorised service agent.
• Replace or repair damaged parts with genuine parts only to avoid safety hazards.
• Place the dolly in a clean, well-lit, and level area, preferably on concrete.
• Avoid using the dolly on unstable surfaces like tarmacadam.
• Keep the dolly clean for optimal performance.
• Do not exceed the maximum motorcycle weight of 500kg.
• Secure the motorcycle to the dolly using appropriate straps.
• When maneuvering, pull rather than push the motorcycle to prevent tipping.
• Maintain balance, wear non-slip shoes, and keep the work area clear of unauthorized persons.
• Avoid using the dolly for tasks it is not designed for.
• Do not use the dolly if damaged, tired, under the influence, or by untrained persons.
• Avoid making modifications to the dolly.
• Clean all parts before storing in a safe area free of grease and oil.

Introduction
The motorcycle dolly is designed to hold a single motorcycle with a side stand, supporting up to 500kg. It can be easily maneuvered around workshops or garages, allowing the motorcycle to be steered into position while keeping the front wheel on the ground. The pivoting feature accommodates various side stand designs, and the holder can be adjusted for most motorbikes.

Frequently Asked Questions (FAQ)

• Q: Can this motorcycle dolly support all types of motorcycles?
  A: The dolly is designed to cater to a majority of motorbikes. However, ensure that your motorcycle’s weight does not exceed the maximum capacity of 500kg.

• Q: Do I need to assemble the motorcycle dolly?
  A: Assembly instructions are provided in the attached parts list. Follow the assembly steps carefully to set up the dolly correctly before use.

• Q: How should I secure my motorcycle to the dolly?
  A: Always use appropriate straps to secure the motorcycle to the dolly when maneuvering to prevent accidents or damage.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

• Maintain the dolly in good condition (use an authorised service agent).
• Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
• Locate the dolly in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
• Ensure that the floor is level and strong enough (preferably concrete) to take the weight of the dolly and the motorcycle.
• DO NOT use the dolly on tarmacadam, as the surface may be unstable.
• Keep the dolly clean for best and safest performance.
• The maximum motorcycle weight is 500kg. DO NOT exceed this rated capacity.
• Use appropriate straps to secure the motorcycle to the dolly when manoeuvring.
• Pull rather than push the motorcycle when manoeuvring on the dolly to reduce the risk of pushing the motorcycle off its side stand.
• Maintain correct balance and footing, DO NOT over reach. Ensure the floor is not slippery and wear non-slip shoes. Keep children and unauthorised persons away from the work area.
• DO NOT use the dolly for a task it is not designed to perform.
• DO NOT use the dolly if it is damaged.
• DO NOT use the dolly when you are tired or under the influence of alcohol, drugs or intoxicating medication.
• DO NOT allow untrained persons to use the dolly.
• DO NOT make any modifications to the dolly.
• Before storing in safe area, ensure that all parts are clean and free of grease and oil.
• WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may occur.
  It must be understood that common sense and caution are factors that cannot be built into this product, but must be applied by the operator.

INTRODUCTION

Motorcycle dolly holds a single motorcycle with a side stand, weighing up to 500kg with weight being dispersed between front and back wheels. Easy to manoeuvre around the workshop or garage. Front wheel stays in contact with the ground allowing the motorcycle to be steered into the desired position. Pivoting feature allows flexibility in side stand designs. Side stand holder can be adjusted to cater to the majority of motorbikes.

SPECIFICATION

ASSEMBLY

Numbers refer to attached parts list.

1. Remove with care all contents from outer packaging, check parts against attached parts list. (note orientation).
2. Place Platform For Arm (1) on ground attach 2 x Swivel Castors with c/w Brake (8), Socket Cap bolt (4), Flat Washers (9), and Domed Steel Nut (11).
3. Attach Swivel Castors (6) using Flat Washers (9), Socket Cap bolt (4). Fasten using Domed Steel Nut (11).
4. Take Platform (1) attach wheel (6b) using Flat Washers (9), Socket Cap bolt (4). Fasten Domed Steel Nut (11) to Arm (3).
5. Place Platform (7) and line up Arm (3) with Platform (7). Insert the two Hex Head Set Screw (2) into the two holes on Arm (3). Tighten using Steel Nuts (5). The support arm can move in relationship to main part and can be adjusted to position/design of side stand before bolt being tightened fully.

OPERATION

WARNING! Ensure that you read, understand and apply the safety instructions before use.
WARNING! DO NOT overload the dolly.

LOADING

1. Position the dolly in a suitable area, checking that the surface on which the dolly will be used is solid and flat.
2. Apply the brakes to the two swivel castors (8).
3. Push the motorcycle onto the dolly, positioning the rear wheel centrally on the main part and support with the side stand on the support arm. Adjust as required and fix in position by tightening set screw (2). Front wheel remains on ground.
4. Secure the motorcycle using suitable straps.
5. Release the braked castors (8) to allow the dolly to be maneuvered.

UNLOADING

1. Apply the brakes to the two castors (8).
2. Holding handle bars lift side stand and remove the motorcycle from the dolly.
3. Store the dolly in a safe, dry, childproof location with the brakes on.

MAINTENANCE

1. Before use, check the frame assembly and platform for cracks and damage.
2. Regularly check that all fasteners are tight.
3. Periodically lubricate the castors.

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No Liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
sales@sealey.co.uk
www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>