HOFTRONIC 5420436 Beam LED Floodlight User Manual
- June 3, 2024
- HOFTRONIC
Table of Contents
- IMPORTANT SAFETY DETAILS
- DIAGRAM
- SPECIFICATIONS
- FIXING INSTRUCTIONS
- GENERAL INFORMATION
- INSTALLATION
- INTENDED USE / APPLICATION
- FUNCTIONAL CHARACTERISTICS
- ENVIRONMENTAL PROTECTION
- COMMENTS / GUIDELINES
- DECLARATION OF CONFORMITY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
USER MANUAL
BEAM LED
FLOODLIGHT SKU
5420436 | 5420467 | 5420498 | 5420528 | 5420559 |
---|---|---|---|---|
5420443 | 5420474 | 5420504 | 5420535 | 5420566 |
5420450 | 5420481 | 5420511 | 5420542 |
IMPORTANT SAFETY DETAILS
- Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
- This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
- This product may NOT be installed by minors or people with a mental disability.
- Do not wire this lantern into the lighting circuit, use a swtiched fuse spur.
- Carefully observe all instructions of warnings that are labelled on, or supplied with your product.
- This product is suitable for outdoor use. If in any doubt, consult a qualified electrician.
DIAGRAM
SPECIFICATIONS
Voltage | AC 220-240V —50/60Hz |
---|---|
Power factor | >0.9 |
Wattage | 10W |
Lumen | 1000lm |
Lamp type | LED 2835 |
CRI | >80 |
Material | Aluminum Die-casting |
Beam angle | 90° |
Product size | 107,3x84x15.5mm |
213x163x18.5mm | 277x214x18.5mm |
Color temp | 4000K/6400K |
Work temp | -20°C-+50°C |
Protection | IP65 |
Housing color | Black |
FIXING INSTRUCTIONS
- Do not wire this lantern into the lighting circuit, use a switched fuse spur.
- This fitting must be earthed, contact a qualified electrician to install a suitable earth facility.
- Ensure the electricity is turned off at the mains before installing or maintaining any electrical fitting.
- Please note: For new installations, check for any electrical cables or pipe work (gas/water) in the vicinity of the intended mounting point for this product before proceeding with the installation.
GENERAL INFORMATION
Do not mount ceiling/wall fittings onto damp sufaces such as newly painted or
plastered areas as this may cause discolouration of the finish.
Tools which may be required:
- Drill
- Cross head screwdriver
- Small electrical slotted screw driver
- Insulation tape
INSTALLATION
- Fasten the adjustable bracket with stainless steel screws
- Connect the main line to the power wire of the lamp
- Note: Before installation. Only use a round cable supplied to connect this fitting (6mm diameter minimum. This is required in order to create a good water seal when connected to the fitting.
- Ensure the terminal connection is made inside a suitable IP65 rated junction box (not included)
- Connect the main line to the power wire of the lamp.
This product should be disposed of responsibly at the end of its life. Please
recycle where facilities exist. Check with your local authority or retailer
for recycling advise.
(Waste Electrical and Electronic Equipment Directive)
INTENDED USE / APPLICATION
Product designed for the use in households and for other similar general
applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should
be performed by an appropriately qualified person. Any activities to be done
with disconnected power supply. Exercise particular caution. Product has a
protective contact/terminal. Failure to connect the protective lead may lead
to electric shock. Mounting diagram: see pictures. Check for proper mechanical
fastening and connection to electrical power prior to first use. The product
can be connected to a supply network which meets energy quality standards as
prescribed by law. To maintain the proper IP protection level, the right
diameter of the power cable should be selected for the cable gland used in the
product.
FUNCTIONAL CHARACTERISTICS
The product can be used indoors and outdoors.
USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product can only be supplied by rated
voltage or voltage within the range provided. It’s forbidden to use the
product with damaged protectivcover. Product must not be used in unfavourable
conditions, e.g. dust, watermoisture, vibrations, explosive air atmosphere,
fumes, or chemical fumes, etc. Nondemountable product. Not suitable for
independent repairs.
ENVIRONMENTAL PROTECTION
Keep your environment clean. Segregation of post-packaging waste is recommended. This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/ neutralising. Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local authorities or sellers of such goods. Used items can also be returned to the seller when new product is purchased, in quantity no larger than the purchased item of the same type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in a given area is recommended.
COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. For more information about Hoftronic products visit www.hoftronic.com. Hoftronic shall not be responsible for any damage resulting from the failure to follow these instructions. Hoftronic reserves the right to make changes in the manual – the current version can be downloaded at www.hoftronic.com.
DECLARATION OF CONFORMITY
DOCUMENTATION
This product has been manufactured and supplied in compliance with all
relevantregulations and directives applicable to all member states of the
European Union.The product complies with all applicable regulations and rules
in the country of sale. Formal documentation such as the declaration of
conformity, the safety data sheeand the product test report is available upon
request.
CE DECLARATION
The product complies with the following directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon
request.
Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands
Made in P.R.C.
www.hoftronic.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>