ANVIZ M5 Pro Outdoor Fingerprint and Card Reader/Controller User Guide

ANVIZ M5 Pro Outdoor Fingerprint and Card Reader/Controller

Product Information

Specifications:

• Product Name: M5 Pro
• Type: Outdoor Fingerprint & Card Reader/Controller
• Quick Guide Version: 1.1

FAQ

What should I do if I encounter issues with the product?

If you face any problems, please contact the distributor for assistance and support.

How do I ensure proper installation of the product?

Make sure to carefully follow the installation steps outlined in the manual to avoid any issues with the product setup.

Can I use any power supply with the product?

To prevent damage, it is recommended to use the original power supply specified for the product or refer to the instructions for suitable alternatives.

What is the warranty coverage for the product?

Any damage caused by incorrect operation or wiring is not covered under warranty. Ensure to strictly adhere to the installation and usage instructions provided.

Package List

Illustration for placing finger

Correct method
( Straighten your finger and then place it on the sensor. Ensure the finger is flat and covers the entire sensor window)

Incorrect method

Installation Diagram

Appearance

Wiring Instruction

Anviz Wiegand Wiring

SC011 authorization setting:
Make sure correct wiring between M5 Pro and SC011, power on them, then move slide switch to ‘PROGRAM MODE’ as below:
Switch in‘PROGRAM’on the SC011: Move slide swith to left(ON).

Wiegand 26 Wiring:
Between M5 Pro and Anviz SAC844 or other Access Controller as below:

Wiegand data output format

1. Anviz Wiegand data output format:
   ALL registered users output devieces’ last eight serial number.(For example, SN of one device is 1050000014470004, then Anviz Wiegand output 14470004.)

2. Wiegand 26 data output format:
   Card user: Output card number.(Decimal)
   Fingerprint user: Output ID number

3. Wiegand output format can be set by PC software

Wiring Type Access Controller

Switching Power Supply

Important notice:
Please carefully follow this wiring instruction. Any damage caused by incorrect wiring is not covered by warranty.

Working with Management Software

Install the Management Software on Computer

Put the CD in the managemet computer. The installation program will run automatically.

How to connect M5 Pro with Software?1st Method: Mini USB

1. Loose the screw on the bottom of M5 Pro, then pull up the front case, seperate from back panel.
2. Connect USB cable between M5 Pro and PC which has installed software.
   Pay Attention:
   If management cards are registered,
   indicator light turns yellow and flashes. You must verify any management card first. If no management card is registered, you can communicate with M5 Pro directly.

2st Method: Mini USB

Enable Communication between M5 Pro and the Management Software CrossChex

• Turn on management software CrossChex
• Go to Device tab. Search and add the M5 Pro to management software CrossChex
• Click Synchronize Time button to communicate with M5 Pro. If Synchronize is successful, the device icon will turn to blue.

The Management Software CrossChex Features

• Device\Backup User: Download user info from M5 Pro to CrossChex
• Device\Download Records: Download records from M5 Pro to CrossChex
• User\Modify: Edit name or other user info. Then click “Upload User”to Upload user info to M5 device
• Record\Search: search and view the records
• Attendance: Calculate, Search results and generate reports
• Data\Backup Database: Backup Database
• Setting\Shift: Set up Time table and Scheduling
• Device\Device Parameter: Set up device, Clear records on M5 Pro or Reset M5 Pro to factory settings

Function Button

Press function button until you hear beeps which means the information of Enroll Card and Delete Card have been eliminated in the device.
Notice: The operation will not delete user data stored in the device.

After that, you MUST register management cards (Enroll Card and Delete Card) to run the machine.

Register Management Cards (Enroll Card and Delete Card)

Operation Guide

IMPORTANT:
M5 Pro is suitable for DC12V power supply only. When connect to DC12V power supply, the indicator light displays blue and flashes fast. Meanwhile, the backlights of fingerprint sensor turn on with beeps.

Register User:

Add One Fingerprint per User Only:

Note:

1. 1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.
   Notice:
   When you place finger on M5 Pro, Red LED flashing with two long beeps means the finger has been registered.
   

Add Card Only
Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.
   Notice:
   When you swipe card on M5 Pro, Red LED flashing with two long beeps means the card has been registered.
   

Add Two Fingerprints of one User:

• Two fingerprints belong to one user ID.

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

Add Fingerprint and Card of one User:
The wiegand output of fingerprint and card are the same.

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

Add Two Fingerprints and Card of one User:

• The wiegand output of fingerprint and card are the same.

  1. Note: 1. After finish enrolling current user, please swipe enroll card and then continue register another user.
  2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

Delete User

Delete Fingerprint or Fingerprint and Card

• After delete one user, you can continue to delete another user or swipe Delete Card to save and exit.
• When fingerprints or card belong to one user ID, you can delete either one to delete this user.

Notice:
When you place finger on M5 Pro, Red LED flashing with long beeps means the fingerprint does not exist in the device.

Delete Card:
After delete one user, you can continue delete another user or swipe Delete Card to save and exit.

Notice:
When you swipe card on M5 Pro, Red LED flashing with long beeps means the card does not exist in the device.

Delete All Users
Delete all uses fingerprints and cards, the device parameter setting do not change.

References

• Anviz Global | Secure workplace , Simplify management

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>