ANVIZ C2 KA Outdoor RFID Access Control Terminal User Manual

V 1.0 C2 KA Outdoor RFID Access
Control Terminal
User Manual

Safety Instructions

Please read this safety instructions carefully before you use the product in order to prevent injury to yourself, others and prevent property damage. The term ‘product’ in this manual refers to the hardware and any item provided with it.

• Do not install or repair the product arbitrarily. This may result in electric shock, fire or product damage.
• Damages caused by any modifications or unfollow installation instructions can void the manufacturer’s Warranty.
• Do not install the product in places with direct sunlight, dust, soot, or gas leak. This may result in electric shock or fire.
• The optimal working environment of C2 KA is both indoor and outdoor. The device fully operates under temperatures -10°C-50°C (14°F-122°F), and humidity 20-90%.
• Do not use damaged power supply adaptors, plugs, or loose electrical sockets. Unsecured connections may cause electric shock or fire. The recommended power supply to C2 KA terminal is DC 12V – 2A.
• Do not drop or cause impacts to the product. The product may malfunction.
• When cleaning the product, wipe it with a clean and dry towel (cloth or cotton).
• If you need to sanitize the product, moisten the cloth or the wipe with a proper amount of rubbing alcohol and gently clean all exposed surfaces including fingerprint sensor. Use rubbing alcohol (containing 70% Isopropyl alcohol) and a clean, non-abrasive cloth like lens wipe.
• Do not apply liquid directly to the surface of the product.
• Do not use the product for anything else than its intended use.

Introduction

Pack List

1 Terminal| 1 Back Mounting Plate| *3 Screws A*

2 Screws B| 1 RJ45 Network Port| 2 RFID Cards

Appearance Description

Lorem ipsum

Installation

Step 1 :
Keep the Back-Mounting Plate perpendicular to the ground. We Suggest at the height of 1.2m (47.24″) from the floor.
Drill 3 screw A holes on the wall according to the Back-Mounting Plate.

Step 2 :
Please punch out the wiring from the outlet hole before installing the mounting bracket and use the screws to fix the mounting bracket on the wall. Use the screwdriver to tighten the screws, follow the direction indicated below to complete the incti6tinn

PLEASE INDICATE THE SCREW DIRECTION
Wiring Connection

|
---|---

A. RJ45 Network Socket

B. Wiegand Input

C. Wiegand Output

E. Power Supply

F. Input

G. RS-485

Wiring with Access Control Power Supply

Access Control Power Supply
Input 110V~240V
Output DC 12V 3A

WIPING WITH ACCESS CONTROL UNIT SCO11
SC011 and the C2 KA devices are authorized by Anviz Wiegand to form a distributed access control system.

Please Configure the Wiegand Output of C2 KA to Anviz Wiegand option, (Refer to Access Settings) and use the SC011 Quick Guide to configure the Wiegand communication correctly.
Please contact Support@anviz.com for more information.

Device Operation

Enter to Main Menu Status
Power On the terminal and wait until the C2 KA flashes a blue breathing light (Normal Operation Status)
En ter Terminal Main Menu

IPress ‘*’ or If key on the terminal.| Terminal will display a white LED light.
---|---

En ter de fau It a dmin account: ‘0’ and p ress ‘4:t’ key.| White LED light will still on standby, waiting for the admin password.
---|---

En ter de fau It a dmin pas sword: ‘12345 and p ress ‘4:fr’ key.| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Insert the desired command code (check next pages for more details).| Blue LED light will still blink faster, informing you ‘re inside the Main Menu
---|---

Press ”” key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you re back in the Normal Operation Status.
---|---

Notice : The default the admin account is ‘0’ and default password is “12345”.

Modify Terminal Management Password
Modi fy Terminal Man age m ent Pas sword

En ter to terminal main menu| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Press Comma nd Code: ‘0’| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---

Insert the new admin password and press ‘#’ key.| Terminal will display a green LED light, informing setup is successful.
---|---

Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Press ‘*’ key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you re back in the Normal Operation Status.
---|---

Notice : The maximum length of the terminal management password is 6 digits number.
It ‘s also possible to modify terminal s password by its webserver.
Register User
Follow the next steps to add a new user on the device

Register User

Enter to terminal main menu| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Press Command Code: ‘1’| Terminal will display a pink LED light, informing you “rein the Terminal Settings Status.
---|---

Input user ID and press ‘4*’ key| Pink LED light will still blink, informing you ‘re in the Terminal Settings Status.
---|---

Input PIN code and press ’44’ key| Terminal will display a green LED light, informing setup is successful.
---|---

Continue to register another User.| Terminal will display a pink LED light, informing you ‘re in the Terminal Settings Status.
---|---

Register a new user using RFID card: Swipe user RFID card| Terminal will display a green LED light, informing setup is successful.
---|---

Continue to register another User.| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---

Press ‘*’ key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you re back in the Normal Operation Status.
---|---

Notice :The maximum User ID length is 12 digits and password maximum length is 6 digits.
Whenever you register a new RFID Card directly on the terminal, the User ID will be sequency assigned, starting with the first empty value (default: 1).
It “s also possible to register new users by terminal s webserver.
Delete User
Follow the next steps to delete an existing user on the device

Delete User

Enter to terminal main menu| Blue LED light will blink faster, informing you ‘re inside the Main Menu.
---|---

Press Command Code: 2′| Terminal will display a pink LED light, informing you ‘re in the Terminal Settings Status.
---|---

Insert the user ID you II delete and press it’ key.| Terminal will display a green LED light, informing setup is successful.
---|---

Continue to Delete another User.| Pink LED light will still blink, informing you’re in the Terminal Settings Status.
---|---

Delete an existing RFID card: Swipe user RFID card you “II delete.| Terminal will display a green LED light, informing setup is successful.
---|---

Continue to Delete another User.| Pink LED light will still blink, informing you’re in the Terminal Settings Status.
---|---

Press ‘*’ key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you re back in the Normal Operation Status.
---|---

Notice : It ‘s also possible to delete existing users by terminal “s webserver.
Delete All Users
Caution: This proceed will remove all users’ information from the terminal

Delete All Users

Enter to terminal main menu| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Press Command Code: ‘2’| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---

Input ‘0000’ and press # key| Terminal will display a green LED light, informing setup is successful.
---|---

Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you “re inside the Main Menu.
---|---

Press ‘*’ key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you “re back in the Normal Operation Status.
---|---

Notice : It ‘s also possible to delete all users’ by terminal ‘s webserver.

Terminal Setup

Setup terminal verify mode:
There are three types of verification mode for the terminal:
Card or ID + Pin Code : The user can use the registered Card or insert ID + Pin Code to access the terminal.
Card Only : The user can only use a registered RFID card to access the terminal.
Card +Password : The user needs to swipe card first, then insert his/her password to access the terminal.
Door Open Verification Mode

Enter to terminal main menu| Blue LED light will bliikbster, informing you “re inside the Main Menu.
---|---
Press Command Code: ‘3’| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---
Input’ 0′ and press ‘#’ key to setup Card or ID+Pin Code Verify Mode| Terminal will display a green LED light, informing setup is successful.
---|---
OR Input ‘1’ and press ‘#’ key to setup only Card verify mode.
OR Input ‘2’ and press ‘#’ key to setup only Card + Pin Code verify mode.
Press key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you re back in the Normal Operation Status.
---|---

Notice : To use the Card + Pin Code verification mode. The user must have the RFID Card and Pin Code under the same ID number. This is only possible by configuring users on the terminal ‘s webserver.
Setup terminal relay delay time The relay delay time range is 0-30 secs. The “0” means the relay output is disabled.
Setup Relay Delay Time

Enter to terminal main menu| Blue LED light will blink faster, informing you re inside the Main Menu.
---|---

Press Command Code: ‘4’| Terminal will display a pink LED light, informing you’re in the Terminal Settings Status.
---|---

Input ‘0’ to ’30’ and press ‘#’ key| Terminal will display a green LED light, informing setup is successful.
---|---

Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you ire inside the Main Menu.
---|---

Press ‘*’ key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you ‘re back in the Normal Operation Status.
---|---

Notice It ‘s also possible to setup the relay delay time by terminal “s webserver.
Setup the working mode of the terminal
There are 2 types of working mode:
Standalone access controller : The terminal works as an access controller. After validate a user successfully, the terminal will trigger the relay output and send a Wiegand output signal.
Reader mode : The terminal will send out a Wiegand output signal with any reading operation. The reader mode can work with 3rd part access control systems with Wiegand input.
Terminal Working Mode

Enter to terminal main menu| Blue LED light will blinkfaster, informing you re inside the Main Menu.
---|---

Press Command Code: ‘5’| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---

Input ‘0’ and press ‘#’ key to setup terminal work as standlone access controller.| Terminal will display a green LED light, informing setup is successful.
---|---
OR Input ‘1’ and press ‘#’ key to setup terminal work as reader.

Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you ‘re inside the Main Menu.
---|---

Press key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you ‘re back in the Normal Operation Status.
---|---

Notice : Please access the terminal “s webserver to configure the ✓eigand settings according to your existing controller Wiegand nput.
Door sensor monitor setup
The door sensor monitor will trigger the alarm (Terminal internal buzzer ) output of the terminal whenever the door is still opened more than the configured time.
Active / Disable Door Sensor Monitor

Enter to terminal main menu| Blue LED light will blinkfaster, informing you ‘re inside the Main Menu.
---|---

Press Command Code: ‘6’| Terminal will display a pink LED light, informing you re in the Terminal Settings Status.
---|---

Input’ 0′ and press ‘#’ key to disable the door sensor monitor function.| Terminal will display a green LED light, informing setup is successful.
---|---
Input ‘1’ and press ‘#’ key to OR active the door sensor monitor function.

Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you ‘re inside the Main Menu
---|---

Press key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you’re back in the Normal Operation Status.
---|---

Notice : It ‘s also possible to active or disable the door sensor monitor by terminal ‘5 webserver, including the delay setup for its alarm.
Set Default Mode (Factory Setup)
Caution :The factory setup will erase all users, records and set the terminal information back to factory mode.
Factory default Setting “.

Enter to terminal main menu| Blue LED light will blink faster, in you “re inside the Main Menu.
---|---
Code number not clear. Please confirm it before official version| Terminal will display a pink LED light, informing you ‘re in the Terminal Settings Status.
---|---
Input ‘000’ and press key| Terminal will display a green LED light, informing setup is successful.
---|---
Insert the desired command code to continue terminal configuration.| Blue LED light will blink faster, informing you “re inside the Main Menu.
---|---
Press “1 key or wait for 10 secs without any operation to exit the Main Menu Management Status.| Blue LED will blink slower, informing you ‘re back in the Normal Operation Status
---|---

Notice : It “s also possible to Set Default Mode (Factory Setup) by terminal ‘s webserver.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>