ANVIZ C2 Slim Fingerprint and RFID Card Terminal User Guide
- June 11, 2024
- ANVIZ
Table of Contents
ANVIZ C2 Slim Fingerprint and RFID Card Terminal
Packing list:
Installation Diaaram &Installation Step 
**Device interface and definition description**
wiegand input-output settings: to connect C2 slim with CrossChex management software, and choose ‘device management\ terminal parameters\Wiegand options (C2 slim)” to set up.
PQ interface definition
| Ser ies | Defin tion |
|---|---|
| Black | GND |
Wiegand
Input
Green & White| Wll
Pink| WIO
Black| GND|
Wiegand
Out
White| W01
G r een| WOO
P8 interface definition
| S eries | Des cri pti on |
|---|---|
| Black | GND |
Door Swit ch
Orange| D/S
Gray| D I M| Doo r Sensor
Black| GND|
RS485
Light Blue| 4BSB
Brow n| 48SA
Access Control Reader & Switching Power Subolv The following wiring is recommended to prevent damage to the device when load is large.
Power Over Ethernet Supply
Power Over theme provides device network communication and the power is enough
for both device and lock to work. The total load should not exceed 12.95W when
using POE supply for directly triggering the electric lock to prevent damage
to C2 slim.
Access Control Reader & SCO11
SCO11 can work with C2 slim by Anviz encrypting Wiegand code authorized to set
up a distributed Access control system. You can buy SC011 from our sales.
Access Control Reader & Access Control Power Supply
Verify the Fingerprint
NOTE:
- It is better for each user to register two fingerprints in case of one finger can’t work.
- Place ringer flat and make sure the center of the finger is on the center of scanner window and press a little hard on scanner, so it can scan as large finger area as possible to extract enough minutia.
- Keep the angle and direction of finger the same each time placing on scanner.
- If your finger has sweat or water, please dry it first and then register the finger.
- If your finger is too dry, make it a little wet or touch the forehead to increase the wetness of the finger, press a little hard on scanner. (The dry finger can cause the finger image not coming out clear enough.)
- Avoid the callus, peeling, orinjury of the finger to ensure the register and identification are successful.
- You can register the thumb first, and then the index finger or middle finger to increase the precision.
Operation Guide
Important:
C2 slim is suitable for DC12V power supply only. When connect to DC12V power
supply, the indicator light displays blue and flashes fast. Meanwhile, the
backlights of fingerprint sensor turn on with beeps.
Register User.
Add One Fingerprint per User Only.
Note:
- After finish enrolling current user, please swipe enroll card and then continue register anotheruser.
- After finish enrollment, please swipe enroll card TWICE to exit enroll status.
Notice:
When you place finger on C2 slim, Red LED flashing with two long beeps means
the finger has been registered.
Add Card Only
Note:
- After finish enrolling current user, please swipe enroll card and then continue to register another user.
- After finish enrollment, please swipe enroll card TWICE to exit enroll status.
Notice:
When you swipe card on C2 slim, Red LED flashing with two long beeps means the
card has been registered.
Add Two Fingerprints of one User:
Two fingerprints belongs to one user ID.
Note:
- After finish enrolling current user, please swipe enroll card and then continue register another user.
- After finish enrollment, please swipe enroll card TWICE to exit enroll status.
Add Fingerprint and Card of one User:
The Wiegand output of fingerprint and card are the same.
Note:
- After finish enrolling current user, please swipe enroll card and then continue to register another user.
- After finish enrollment, please swipe enroll card TWICE to exit enroll status.
Add Two Fingerprints and Card of one User
The wiegand output of fingerprint and card are the same.
Note:
- After finish enrolling current user, please swipe enroll card and then continue register another user.
- After finish enrollment please swipe enroll card TWICE to exit enroll status
Delete Fingerprint or Fingerprint and Card
- After delete one user, you can continue to delete another user or swipe Delete Card to save and exit.
- When fingerprints or card belong to one user ID, you can delete either one to delete this user.
Notice:
When you place finger on C2 slim, Red LED flashing with long beeps means the
fingerprint does not exist in the device.
Delete Card:
- After delete one user, you can continue delete another user or swipe Delete
- Card to save and exit.
Notice:
When you swipe card on C2 slim, Red LED flashing with long beeps means the
card does not exist in the device.
Delete All Users
Delete all uses fingerprints and cards, the device parameter setting do not
change.
Working with Management Software
Install the Management Software on Computer
Enable Communication between C2 slim and the Management Software CrossChex.
- Turn on management software CrossChex
- Go to Device tab. Search and Add the C2 slim to management software CrossChex
- Click Synchronize Time button to communicate with C2 slim. If Synchronize is successful, the device icon will turn to blue.
The Management Software CrossChex Features.
- Device\Backup User:Download user info from C2 slim to CrossChex
- Device\Download Records:Download records from C2 slim to CrossChex
- User\Modify: Edit name or other user info. Then click ‘Upload User’ to Upload user info to C2 slim device.
- Record \Search:Search and view the records
- Attendance:Calculate, Seach results and Generate reports
- DatalBackup Database;Backup Database
- Setting\Shift:Set up Time Table and Scheduling
- Device\Device Parameter:Set up device, Clear records on C2 slim or Reset C2 slim to factory settings.
- Any questions? Please feel free to send emails support@anviz.com to get support.
https://bit.ly/2WugbYp.
https://bit.lv/2VnOwh6.
https://bit.lv/2J9qA95.
- Anviz brand and product are trademarked and protected under law of the United States.
- Unauthorized use is prohibited.
- For more information, please visit
- www.anviz.com, or send email to
- sales@anviz.com. for more help
- ©2021 Anviz Global Inc. All Rights Reserved.