ANVIZ C2 Slim Outdoor Standalone Access Control Terminal User Guide

ANVIZ C2 Slim Outdoor Standalone Access Control Terminal User Guide

Packing list

Installation diagram installation step

Fix the Device Fix back board,connect with the wire. Fix the device from the bottom and screwing it. Make sure fixed OK.

Device interface and defination description

J2 interface definition

Important notice: Please follow the wiring diagram as it is displayed. Damaged products due to improper wiring are not covered by product warranty.

wiegand input\output settings: to connect C2 slim with CrossChex management software, and choose “device management\ terminal parameters\Wiegand options (C2 slim)” to set up.

P9 interface definition

p8 interface definition

Access Control Reader & Switching Power Supply

The following wiring is recommended to prevent damage to the device when

load is large.

Power Over

Ethernet Supply Power Over Ethernet provides device network communication and the power is enough for both device and lock working.Total load should not exceed 12.95W when using POE supply for directly triggering the electric lock to prevent damage to C2 slim.

Access Control Reader & SC011 SC011

can work with C2 slim by Anviz encrypt wiegand code authorized to set up a distributed Access control system.You can buy SC011 from our sales.

Access Control Reader & Access Control Power Supply

In order to protect the environment, Anviz has decided to go “CD Free” campaign since June 1st 2019. We will provide QR code for you to download the electronic documents to make sure that you understand how to install and use Anviz devices.

verify the finger print

correct method

incorrect method

NOTE:

• It is better for each user to register two fingerprints in case of one finger can’t work.
• Place Finger flat and make sure the center of the finger is on the center of scanner window and press a little hard on scanner, so it can scan as large finger area as possible to extract enough minutia.
• Keep the angle and direction of finger the same each time placing on scanner.
• If your finger has sweat or water, please dry it first and then register the finger.
• If your finger is too dry, make it a little wet or touch the forehead to increase the wetness of the finger, press a little hard on scanner . (The dry finger can cause the finger image not coming out clear enough.)
• Avoid the callus, peeling, orinjury of the finger to ensure the register and identification successful.
• You can register the thumb first, and then index finger or middle finger to increase the precision.

Operation Guide

Important:

C2 slim is suitable for DC12V power supply only. When connect to DC12V power supply, the indicator light displays blue and flashes fast. Meanwhile, the backlights of fingerprint sensor turn on with beeps.

Add One Fingerprint per User Only:

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
   After finish enrollment, please swipe enroll Enroll Card   TWICE to exit enroll status. Blue flashe

Notice: When you place finger on C2 slim, Red LED flashing with two long beeps means the finger has been registered.

Add Card Only:

Note: 1. After finish enrolling current user, please swipe enroll card and then continue register another user. 2. After finish enrollment, please swipe enroll card TWICE to exit enroll status. 1.5% Enn

Notice: When you swipe card on C2 slim, Red LED flashing with two long beeps means the card has been registered.

Add Two Fingerprints of one User: Two fingerprints belongs to one user ID.

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.
   

Add Fingerprint and Card of one User:

The wiegand output of fingerprint and card are the same.

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

Add Two Fingerprints and Card of one User: The wiegand output of fingerprint and card are the same.

Note:

1. After finish enrolling current user, please swipe enroll card and then continue register another user.
2. After finish enrollment, please swipe enroll card TWICE to exit enroll status.

Delete User:

Delete Fingerprint or Fingerprint and Card After delete one user, you can continue to delete another user or swipe Delete Card to save and exit.

When fingerprints or card belong to 1.Swipe one user ID, you can delete either one Delete Card to delete this user. Red flas

Notice: When you place finger on C2 slim, Red LED flashing with long beeps means the fingerprint does not exist in the device.

Delete Card:

After delete one user, you can continue delete another user or swipe Delete Card to save and exit.

Notice:

When you swipe card on C2 slim, Red LED flashing with long beeps means the card does not exist in the device.

Delete All Users

Delete all uses fingerprints and cards,the device parameter setting do not change.

Working with Management Software

Install the Management Software on Computer

Put the CD in the management computer.The installation

How to connect C2 slim with Software? program will run automatically. Connect C2 slim to Network

Enable Communication between C2 slim and the Management Software Cross Chex.

• Turn on management software CrossChex
• Go to Device tab. Search and Add the C2 slim to management software CrossChex
• Click Synchronize Time button to communicate with C2 slim. If Synchronize is successful, the device icon will turn to blue.

The Management Software Cross Chex Features.

• Device\Backup User:Download user info from C2 slim to CrossChex
• Device\Download Records:Download records from C2 slim to CrossChex User\Modify:Edit name or other user info.Then click ‘Upload User’ to Upload user info to C2 slim device. 4, Record \Search:Search and view the records
• Attendance:Calculate, Seach results and Generate reports
• Data\Backup Database;Backup Database
• Setting\Shift:Set up Time Table and Scheduling
• Device\Device Parameter:Set up device, Clear records on C2 slim or Reset C2 slim to factory settings.

Any questions? Please feel free to send emails support@anviz.com to get support.

References

• Anviz Global | Secure workplace , Simplify management

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>