vtech 5728 Roaaar Egg Pterodactyl Chopper Instruction Manual

: July 17, 2024
: vtech

Table of Contents

INTRODUCTION
INCLUDED IN THE PACKAGE
GETTING STARTED
IMPORTANT: BATTERY INFORMATION
HOW TO SWITCH
PRODUCT FEATURES
CARE & MAINTENANCE
TROUBLESHOOTING
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

vtech 5728 Roaaar Egg Pterodactyl Chopper

vtech 5728 Roaaar Egg Pterodactyl Chopper

INTRODUCTION

Switch into fun with the Switch & Go® Pterodactyl Dragster.
Transform this agile Pterodactyl into speedy race car and back in just a few simple steps. 60+ sounds and phrases, cool LED effects and an animated LCD screen bring the action to life in your very own dino universe.

Introduction

INCLUDED IN THE PACKAGE

Switch & Go® Pterodactyl Dragster
Quick Start Guide

WARNING

All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy, and should be discarded for your child’s safety.

NOTE

Please save this manual as it contains important information.

GETTING STARTED

Exit Try-Me Mode:

To exit try-me mode, need to wake up the unit first, then transform from Dino mode to Vehicle Mode. Normal play mode will then proceed.

WARNING:

Adult assembly required for battery installation.
Keep batteries out of reach of children.

Battery Removal and Installation

Make sure the unit is turned Off.
Locate the battery cover on the bottom of the unit. Use a screwdriver to loosen the screw and then open the battery cover.
If a used batteries is present, remove this batteries from the unit by pulling up on one end of the battery.
Install 2 new AA (AM-3/LR6) batteries following the diagram inside the battery box. (For best performance, alkaline batteries or fully charged Ni-MH rechargeable batteries are recommended).
Replace the battery cover and tighten the screw to secure.

Getting Started

IMPORTANT: BATTERY INFORMATION

Insert batteries with the correct polarity (+ and -).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries.
Only batteries of the same or equivalent type as recommended are to be used.
Do not short-circuit the supply terminals.
Remove batteries during long periods of non-use.
Remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES
Remove rechargeable batteries (if removable) from the toy before charging.
Rechargeable batteries are only to be charged under adult supervision.
Do not charge non-rechargeable batteries.

HOW TO SWITCH

Begin in Dino mode.
Flip the DIno’s feet backward.
Swing the wings down so that they are parallel to the unit.
Close the dino’s beak.
Flip the black hood pieces on the underside of the wings outward.
Flip the wing tips forward.
Fold the wings in, then push them down.
Snap the wings’ side panels down and swing the legs forward.
The unit is now in Vehicle mode.

PRODUCT FEATURES

Power Switch
To turn the unit On or to adjust the volume, slide the switch to the Low or High Volume position. To turn the unit Off, slide the switch to the Off position.
Head Button
In Dino mode, press the Head Button to learn fun Dino facts and cool dinosaur sounds. A light projection will accompany the response. In the Vehicle mode, press the Head Button to hear fun phrases and great vehicle sounds.
Action Button
Press the Action Button to hear cool sound effects.
LCD Screen
The LCD Screen shows dino eye animations in Dino mode and shows driver animations in Vehicle mode.
LED Lights
The LED Lights flash along with the sounds in Dino mode and Vehicle mode.
Automatic Shut-off
To preserve battery life, Switch & Go® Pterodactyl Dragster will automatically power down after several seconds without input. The unit can be turned on again by pressing the Head Button or Action Button. The unit will also automatically turn off when battery power is very low.

Notes: If the unit repeatedly powers down or has abnormal responses when the unit is switched on, please insert new batteries and try switching it on again.

CARE & MAINTENANCE

Keep the unit clean by wiping it with a slightly damp cloth.
Keep the unit out of direct sunlight and away from any direct heat sources.
Remove the batteries if the unit will not be in use for an extended period of time.
Do not drop the unit on hard surfaces and do not expose the unit to moisture or water.

TROUBLESHOOTING

If for some reason the unit stops working or malfunctions, please follow these steps:

Turn the unit Off.
Interrupt the power supply by removing the batteries.
Let the unit stand for a few minutes, then replace the batteries.
Turn the unit On. The unit should now be ready to use again.
If the unit still does not work, replace with a new set of batteries.

IMPORTANT NOTE:

If the problem persists, please call our Consumer Services Department at 1-800-521-2010 in the U.S.,1-877-352-8697 in Canada, or visit our website vtechkids.com and fill out our Contact Us form located under the Customer Support link.
Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to contact us with any problems and/or suggestions you might have. A service representative will be happy to help you.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

ore of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information

Trade Name : VTech®
Model: 5728
Product Name: Switch & Go® Pterodactyl Dragster
Responsible Party: VTech Electronics North America, L.L.C.
Address: 1156 W. Shure Drive, Suite 200 Arlington Heights, IL 60004
Website: vtechkids.com

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. CAN ICES-003(B)/NMB-003(B)