HOFTRONIC 1M3W-6TMD Malaga LED Porch Lights Dimmable User Manual

1M3W-6TMD Malaga LED Porch Lights Dimmable
User Manual

MALAGA LED PORCH LIGHTS DIMMABLE

INSTALLATION MANUAL
Please read this manual carefully before installing and using the downlights. Do this for your own safety and to prevent damage of the product. This manual is applicable to  he LED recessed downlights. The kit is delivered ready for use with the amount of downlights you selected, including five meters cable per spot, dimmable LED driver, connectors and a remote control.

1. First check whether all the parts are in the box and test the kit before installing it permanently.
2. Drill the holes with a saw size of 28 mm to the desired position. Position the cables of the LED recessed spotlights at the desired location.
3. Place the LED recessed spots in the drill hole so that the two springs touch the material. Push both springs in succession against the downlight and put the downlight in place.
4. Connect the LED recessed spots to the connector, note that each connector has 6 ports.
5. Switch the power group off, then connect the transformer to 230V (INPUT). N = cable blue and L = cable brown. Connect the INPUT of the transformer with an on / off switch (fixed mains current).
6.  If the transformer is installed outdoors, it must be placed in a water / moisture resistant housing (ART. NO. 396302). The recessed spots can only be used as recessed spots in a covered area.
7. The remote control supplied as standard has already been paired with the transformer, insert the batteries into the remote control, the set is now ready for use. The wall dimmer is also supplied as standard.
8. Optionally, the set can be extended with a 4-channel remote control.

FREQUENTLY ASKED QUESTIONS

How many spots can I connect at least?****

– 1 spot

The light does not go on what now?****

– Try plugging the spotlight into a different port and then check to see if it works. If it still does not work, reach out to your distributor.

Can I extend the set?****

– The set is expandable, standard is a 1-channel remote control and a wall dimmer supplied, Do you need more than 12 spots? Then order multiple sets and a 4 channel remote control this allows you to control up to 36 spots.

STANDARD REMOTE CONTROL + WALL DIMMER
The remote control is taught-in as standard from factory setting and does not have to be registered on the transformer. Insert the supplied batteries into the remote control, which is now ready for use. Below you will find the functions of the remote control.

1. SET – Pairing with driver
2. ON – Turn on
3. OFF – Turn off
4. Brightness (+) – Gradually increase brightness
5. Brightness (-) – Gradually decrease brightness
6. Step Brightness (+) – Brightness in steps 10%, 30%, 70%, 100%
7. Step Brightness (-) – Brightness in steps 10%, 30%, 70%, 100%
8. Mode – Brightness 100%
9. Night light – Brightness 10%
10. DIY1/DIY2 – Congure DIY modus
11. Delay – Turn off after 30 seconds

Pairing Remote Control

1. Disconnect the power of the driver
2. Press and hold the SET button
3. Connect power to the driver
4. Release the SET button as soon as the lights flicker
5. Press the Mode button 4 times repeatedly

The wall dimmer must be paired with the driver, this is not set by default. Below you will find the functions of the wall dimmer and how it is paired to the driver.

1.  ON/OFF – Turn on/off
2. Brightness (+) – Gradually increase brightness
3. Brightness (-) – Gradually decrease brightness
4. Night light – Brightness 10%
5. Delay – Turn o after 30 seconds

Pairing wall dimmer

1. Disconnect the power of the driver
2. Press and hold the ON/OFF button
3. Connect power to the driver
4. Release the ON/OFF button
5. Press the Night light button 3 times

OPTIONAL 4 CHANNEL REMOTE
The remote control must be paired with the driver, this is not set by default. Below you will find the functions of the remote control and how it is paired to the driver.

1. ON – Turn on
2. OFF – Turn off
3. Brightness (+) – Gradually increase brightness
4. Brightness (-) – Gradually decrease brightness
5. Dim – Brightness in steps 10%, 30%, 70%, 100%
6. Night light – Brightness 10%
7. Zone – Selection for the control zone

Pairing Remote Control

1. Disconnect the power of the driver
2. Select the zone with the Zone button
3. Press and hold the DIM button
4. Connect power to the driver
5. Release the DIM button
6. Press the ON button 4 times repeatedly

DECLARATION OF CONFORMITY

DOCUMENTATION
This product has been manufactured and supplied in compliance with all relevant regulations and directives applicable to all member states of the European Union. The  roduct complies with all applicable regulations and rules in the country of sale.  Formal documentation such as the declaration of conformity, the safety data sheet and the  roduct test report is available upon request.

CE DECLARATION
The product complies with the following directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon request.

** Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands
Made in P.R.C.**
www.hoftronic.com

References

• HOFTRONIC - HOFTRONIC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>