FUNPOWER FT031XHDM Remote Control Transmitter User Manual

FUNPOWER FT031XHDM Remote Control Transmitter

Product Information

Specifications

• Model: FT0313HDM Remote Control Transmitter
• Battery: 2pcs of 1.5V AAA batteries
• FCC ID: 2ABUP-FT031XHDM
• IC Caution: IC25540-FT031XHDM

Product Usage Instructions

LED Indicator
The LED indicator controls the ON/OFF function of the fan.

Speed Control
Adjust the speed of the fan from levels 1 to 6 using the + and – keys.

Breeze Mode Timer
Set the fan to Breeze Mode between Speed 2 to Speed 4 for a unique airflow pattern.

Fan and Lighting Control
Toggle ON/OFF for both the fan and lighting. Adjust brightness using the respective keys.

Direction Control
Change the direction of the fan to blow air either downward or upward. Press and hold the direction key for 5 seconds to activate this function.

Timer Setting
Set the fan to stop after 2, 4, or 8 hours using the timer control. Cancel the timer by pressing + or – keys.

Use Precautions

1. If the LED indicator doesn’t turn on, check the battery installation.
2. If the LED indicator flashes, replace the batteries as they may have low voltage.
3. Remove batteries from the transmitter if not in use for an extended period.

FAQ

• Q: How do I know when to replace the batteries?
  A: The LED indicator will flash when the batteries have low voltage, indicating it’s time for a replacement.

• Q: Can I control both fan speed and lighting brightness simultaneously?
  A: Yes, you can adjust the fan speed and lighting brightness independently using the respective control keys.

OVERVIEW

Operation Instructions

1. LED indicator

   • Gear display.
   • Other key function is an effective indication.

2. OFF the Fan and lighting

3. ON/OFF the Fan

   • When fan shut down, press this button, the fan run at the speed before fan shutdown.
   • When fan are on, press this button, the fan shut down.

4. Speed of the fan (1~6 level)

   • The “+” key increases the fan gear. The higher the gear, the higher the fan speed.
   • The “-” key lowers the fan gear, and the lower the gear, the lower the fan speed.
   • The number of indicators displayed corresponds to the current fan gear.
   • The lowest gear is 1st gear and the highest gear is 6th gear.

5. ON/OFF the Lighting

   • When the light is off, press this button to turn it on.
   • When the light is on, press this button to turn it off.

6. Brightness control

   • The “+” key increases brightness.
   • The “-” key lowers brightness

7. Breeze Mode: Between Speed 2 to Speed 4, at 40 seconds in a curve and circle speed. Reach one specific speed, it changes to another speed.

8. Fan timing control
   Set up the timer at 2 hours, 4 hours, 6 hours.

   • 2H press this key,the fan will stop after 2 hours.
     4H press this key,the fan will stop after 4 hours.
     8H press this key,the fan will stop after 8 hours.

   • The timing function of the key works when the fan is running.

   • Press the key “+” or ”-” will cancel the timer.

   • The latest timer will take place the previous one.

   • The number of LED lights corresponds to the number of hours when the fan is shut down.

9. Direction of the fan

   • Press the key to control the direction of the fan to make the wind blow on the ground. It is usually used in summer. Press and hold this key for 5 seconds to turn on this function. At the same time, the LED lights will display from bottom to top in order. Finally, all the indicators will turn on and off.
   • Press the key to control the direction of the fan, so that the wind blows upward from the ceiling. It is usually used in winter. Press and hold this key for 5 seconds to turn on this function. At the same time, the LED lights will be displayed in order from top to bottom. Finally, all the indicators will turn on and off.

10. The transmitter use 2pcs of 1.5V AAA battery, please install the battery correctly.

Use precautions

1. When press the key of transmitter, the LED indicator doesn’t on, please inspect the battery installation..
2. hen press the key of transmitter, the LED indicator flashing, which means the battery get low voltage, please replace a new one.
3. Please pull out of the battery from the transmitter when leaving unused for a long time.

FCC Instructions

This product has been tested and found to comply with the limits for a Class B digital device, under Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the product and receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may causeUndesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.

FCC ID: 2ABUP-FT031XHDM

IC Caution: RSS-Gen Issue 5 “&” RSS-Gen numéro 5
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation
   of the device.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment.

RF exposure statement:
The equipment complies with IC Radiation exposure limit set forth for uncontrolled environments.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>