The Home Depot A01-008 Ceiling Fan with Lights User Manual

The Home Depot A01-008 Ceiling Fan with Lights User Manual

• Mounting bracket

• Coupling cover

• Canopy

• 3.9” downrod
  7.8” downrod
  

• Remote & Remote holder

• Remote receiver

NOTE:
Remote control requires AAA 1.5V battery x 2pcs (not included)

Installation kit

Note:
Some extra hardware may be included. The quantity listed above is the number required for installation

1. Be sure the power to the wires you are working on is disconnected, either the fuse is removed or the circuit breaker is turned off. Turning the power off using the light switch is not sufficient to prevent electrical shock.
2. A qualified licensed electrician is required for the installation.
3. The outlet box and support structure must be securely mounted and capable of reliably /supporting a minimum of 70 pounds. Use only UL (cUL for Canadian Installation) listed mounting boxes marked “FOR FAN SUPPORT”.
4. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor.
5. Do not operate reversing switch while fan blades are in motion (if applicable). Fan must be turned off and blades stopped before reversing blade direction.
6. Do not place any objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan.
8. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened soft cloth will be suitable for the cleaning.
9. After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor on one side of the outlet box.
10. Electrical diagrams are reference only, different fan light may have different light shade and bulbs.
11. Use only our replacement parts. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

Warning:
To reduce the risk of personal injury, use only the two steel screws and washers provided with the outlet box for mounting to the outlet box. Most outlet boxes commonly
used for the support of lighting fixtures are not acceptable for fan support and need to  be replaced, consult a qualified electrician if in doubt.
To reduce the risk of fire, electric shock or person injury, mount fan to outlet box marked “acceptable for fan support”.
To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades

Installation Preparation

Tools You Need

• Ladder

• Pliers

• Wire Strippers

• Screwdrivers

• Power Drill (optional)

• Drill Bit (optional)

If mounting to a support structure, you will also need the optional tools.

What to Expect with Your Installation

• Must be able to secure the fan to building structure or funerated outlet box

• Assess location

• Check box to see fan weight

Installation Step 1 (Threaded Tube Installation)

1. Assemble the Threaded Tube
   Step 1. Take off the dowered hub and hub cover from the shade arm hub.
   Step 2. Pass the wires through the downrod tube / tube cover / threaded tube and shade arm hub in sequence, Twist the threaded tube into the connector tightly. (Fig. 1)
   
   Step 3. Fasten shade arm hub with a nut.

2. Assemble the Shade Arms
   Step 1. Take off screws from the lampshade frame and shade arms.
   Step 2. Tighten the nut first to assembled the shade arms.(Fig. 2)
   

NOTES:

1. Install the two opposing shade arms first to pull the lampshade frame up to avoid imbalance.
2. During transportation, the lampshade frame may tilt. By righting it, the shade arms can be installed smoothly.

Installation Step 2 (Assemble the Donwood)

Assemble the dowered
Step 1. Remove the clevis pin and “R” pin from the dowered assembly.
Step 2. Assemble the canopy and coupling cover. (Fig. 3)

Step 3. Route wires through dowered assembly.
Step 4. Loosen the set screws from the downfold hub but do not take off. Align the holes at the bottom of the dowered with the holes in the dowered hub. Carefully insert the clevis pin through the holes in the collar and dowered. Be careful not to jam the clevis pin against the wires inside the dowered. Insert the “R” pin into the end of the clevis pin (Fig. 4).

Step 5. Fix the downrod with the set screws on the hub.

Installation Step 3 (Mount the Bracket)

**Option 1

Option 2

**

Option 1: With Outlet Box
Fix the mounting bracket onto the outlet box with screws from the outlet box.
Option 2: Without Outlet Box
Fix the mounting bracket onto the solid wood structure with 2 wood screws.

Installation Step 4 (Connect the Wires)

1. Hang the Fan
   Lift the dowered into the mounting bracket. Rotate the dowered until the tab in the mounting bracket is seated in the fixation slot in the dowered ball (Fig. 5).

2. Wire the Fan Fixation Slot Tab Fig. 5
   
   Step 1. Insert the remote receiver to the bracket. (Fig 6)
   
   Step 2. Connect the two wires from the receiver to the fan wires, color matching.
   Step 3. Connect the receiver black wire to your house live wire, white wire to your neutral wire, copper wire from the dowered to your ground wire. (Fig 7)
   
   Step 4. After connecting the wires, spread them apart so that the live wires are on one side of the outlet box and the neutral wires are on the other side

Installation Step 5 (Fix the Canopy)

Step 1. Slide the coupling cover downward to cover the dowered hub.
Step 2. Slide the canopy up to the ceiling and attach it to the mounting bracket with the screws provided. Tighten all screws securely.
Step 3. Install light bulbs (E12 x 6, Max 40W each, not included)

Install the Remote Holder

1. Insert 2 batteries before using: AAA 1.5V battery x 2pcs (not included)
2. Install the remote holder onto the wall with screws.

Remote Control Instructions

NOTE:
Please insert 2 batteries before using. AAA 1.5V battery x 2pcs (not included)

①: Turn off the fan and lights.
②⑦: “F” refers forward fan direction.”R” refers reverse the fan.
③④⑨⑩⑫⑬: 1/2/3/4/5/6 for fan speeds.
⑤⑭⑮: 1H/2H/4H for timing the fan.
⑥: Turn on/off the lights.
⑧: Natural wind of the fan, fan speed will change automatically when use this function.
⑪: Turn off the fan.

REMOTE SIGNAL PAIRING : If the remote control looses signal of the fan, turn off the power from wall switch, then turn it on, press ① immediately for around 3 seconds, after the fixture beeps or flashes, then it’s down.

1. Fan doesn’t work
   • Make sure the fixture is connected to an ON/OFF wall switch, not a dimmer switch.
   • Check the remote control battery (not included in this package).
   • Check the circuit breaker to ensure the power is on.
   • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to  the wiring diagram.
2. Lights Do Not Light Up / Flicker / Noisy Operation
   • Make sure the fixture is connected to an ON/OFF wall switch, not a dimmer switch.
   • Check your power and switch to make sure it’s powered on.
   • Check the bulb to make sure it’s installed correctly.
   • Change a new bulb.
3. Noisy Operation
   • Tighten the light fitting and blade bottom cover.
   • Re-tighten all screws on the bracket, downrod, and fan blades (do not over tighten).
   • Check to see if any of the blades are cracked. If so, replace all of the blades.
   • Remote does not work
   • Make sure the battery is installed correctly.
   • Pair the remote control again.
   • Install 2 new batteries.

Clean And Care

To clean, wipe the fixture with a soft cloth. Spraying from chemical cleaners can discolor the finish of the fixture. Do not use scouring pads, powders, steel wool, or abrasive paper to clean this fixture.

Ordering Parts

Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from the place of purchase. Use exact wording from diagrams when ordering parts.
Scan for Installation Video

Documents / Resources

| The Home Depot A01-008 Ceiling Fan with Lights [pdf] User Manual
A01-008 Ceiling Fan with Lights, A01-008, Ceiling Fan with Lights, Fan with Lights, Lights
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>