EDIFIER S3000MKII Active Speaker User Guide

: July 9, 2024
: Edifier

Table of Contents

What’s in the box?
Note:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EDIFIER S3000MKII Active Speaker User Guide

What’s in the box?

Wiring Connection

Note:

Images are for illustrative purposes only and may differ from the actual product.
The bundled USB connecting cable is for audio streaming only. Do not use it for device charging.
For the need of technical improvement and system upgrade, information and specifications contained herein may be slightly different from actual product. If any difference is found, the actual product prevails.

Cable connection

Note:

Power input: 100-240V~ 50/60Hz * This plug type is meant for illustration purpose only.
- Power on: Switch the main power buttons on the rear panels to “ON”.
- Power off: Switch the main power buttons to “OFF”.

Source selection

Bluetooth connection

Note:

On your Bluetooth device, you can search for and connect to S3000MK in any mode. S3000MK will try to connect to the device that is connected last time when powered on again. You can only play audio via Bluetooth when S3000MK is in Bluetooth mode.
Pin code for connection is “0000” if needed.
To enjoy all Bluetooth functions of this product, make sure that your audio source device supports A2DP and AVRCP profiles.
To disconnect from the current Bluetooth device, press and hold the “Volume/Input” knob on the rear panel of the right speaker (R) or the ” **” button on the remote control for over 2s
**
USB connection

Note:

USB interface of S3000MK is built on USB Audio Class 2.0, which supports high-resolution audio with sample rate up to 192kHz. To play such audio, a driver needs to be installed on your Windows computer. You can visit www.edifier.com, search for “S3000MKII”, go to its detail page, scroll down to the support information, and click the link to download the driver.
For further information about the driver, access the following link for details: https://www.xmos.com/support/usb-audio-driver-support
Make sure that S3000MK is set as the audio output device. (1) For Windows users, access “Control Panel”→”Sound”→”Play”→”Set as Default” to set “XMOS USB Audio” as the current audio output device. (2) For Mac users, access “System Preferences”→”Sound”→”Output” to select “EDIFIER S3000MKII” as the current audio output device.
In USB mode, the following sample rates are supported: 44.1kHz, 48kHz, 96kHz, and 192kHz.

Note:

The play control in USB mode may vary depending on different audio player applications.
The volume levels of S3000MK and your device are not synchronized. To adjust the volume levels, adjust separately.

Play control

Sound effects

Standby & wake-up

Battery replacement

Total output power: L/R (Treble): 8W+8W, L/R
(Mid-range and bass): 120W+120W
Frequency response: 38Hz-40kHz

To learn more about EDIFIER, please visit www.edifier.com
For EDIFIER warranty queries, please visit the relevant country page on www.edifier.com and review the section titled Warranty Terms.
USA and Canada: service@edifier.ca
South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact information.
Hereby, Edifier International Limited declares that the radio equipment type EDF100078 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://[www.edifier.com](http://www.edifier.com)/int/eu-doc.html
L: FCC ID: Z9G-EDF229 IC : 10004A-EDF229
HVIN: EDF229
R: FCC ID: Z9G-EDF219 IC: 10004A-EDF219 Declaration for EU
Frequency Band (Bluetooth): 2.402GHz ~ 2.480GHz
Frequency Band (5.8G): 5.729GHz ~ 5.845GHz
RF Power Output (Bluetooth): ≤10 dBm (EIRP) RF Power Output (5.8G): ≤14 dBm (EIRP)
There is no restriction of use.

Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries.

For more information, please visit our website:

@Edifierglobal

@Edifier_Global

EDIFIER ConneX app

Model: EDF100078
Edifier International Limited P.O. Box 6264
General Post Office Hong Kong
Tel: +852 2522 6989
Fax : +852 2522 1989
www.edifier.com
© 2023 Edifier International Limited. All rights reserved. Printed in China
NOTICE:
For the need of technical improvement and system upgrade, information contained herein may be subject to change from time to time without prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from actual product. If any difference is found, the actual product prevails.