Andis MBG-2 Easy Clip Groom Detachable Blade Clipper Kit User Manual

July 8, 2024
Andis

Andis MBG-2 Easy Clip Groom Detachable Blade Clipper Kit User Manual

The item pictured may differ from the actual product.
Congratulations! You just went first class when you bought this Andis clipper. Careful workmanship and quality design have been the hallmarks of Andis products since 1922.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using the Andis clipper.
DANGER: To reduce the risk of electric shock:

  1. Do not reach for an appliance that has fallen into the water. Unplug immediately. Never use a clipper near water.
  2. Do not use it while bathing or in a shower.
  3. Do not place or store appliances where they can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
  4. Always unplug this appliance from the electrical outlet immediately after use. Unplug by holding and pulling on the plug, not the cord.
  5. Unplug this appliance before cleaning, removing, or assembling parts.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:

  1. An appliance should never be left unattended when plugged in.

  2. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the
    hazards involved.

  3. Children shall not play with the appliance.

  4. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Andis.

  5. Never operate this appliance if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an Andis Authorized Service Station for examination or repair.

  6. Keep the cord away from heated surfaces.

  7. Never drop or insert any object into any opening.

  8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

  9. Do not use this appliance with a damaged or broken blade or comb, as injury to the skin may occur.

  10. To disconnect turn the control to “0” and then remove the plug from the outlet.

  11. WARNING: During use, do not place or leave the appliance where it may be (1) damaged by an animal or (2) exposed to the weather.

  12. Oil blades frequently. Blades may become hot during use.

Please read the following instructions before using your new Andis clipper. Give it the care a fine, precision-built instrument deserves and it will give you years of service. Before starting your clipper, remove the blade guard (some models may not have a blade guard). Plug the cord into an electrical outlet, operate at the rated current, and cycle as noted on the unit. To start the clipper move the switch button to the “1” position; to stop, move the switch button back to the original position. After using your Andis clipper, rewrap the cord, and store it in a safe place.

USING ATTACHMENT COMBS

(Some models do not have attachment combs)
You can set the blades for a longer cut by using any of the attachment combs made for your Andis clipper. The attachment combs are easy to use–they snap on and off. To attach a comb, slip the attachment onto the top edge of the blade and snap it down onto the bottom edge of the blade (Figures A & B). The attachment combs help guide the hair to the blades and give you precise control of hair lengths. The length of the trim is indicated on each attachment comb. Use the chart below to find the approximate lengths of the cut. Different blade angles in relation to the skin, thickness, and texture of the hair will vary the cutting length.

CLIPPING GUIDE

USER MAINTENANCE
Cleaning and user maintenance shall not be done by children without supervision. The internal mechanism of your clipper has been permanently lubricated at the factory. Other than the recommended maintenance described in this manual, no other maintenance should be performed, except by Andis Company or an Andis Authorized Service Station. If the supply cord is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.

REMOVING THE BLADE SET
To remove the blade set, first make sure your clipper motor is switched off, then push down on the blade with both thumbs (Figure C) and slide the blade off the blade hinge. If your blade hinge should snap closed and is ush with the clipper, use a small standard screwdriver to pry the tongue of the hinge out (Figure D).
NOTE: Hair may accumulate in the front cavity of the housing under the blade. If this happens, you can clean out the hair by brushing out the cavity with a small brush or an old toothbrush while the blade is off the clipper (see Figure D for the location of the e cavity being referenced).

REPLACING OR CHANGING THE BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure E) and with the clipper running, push the blade toward the clipper to lock into position.

BLADE TEMPERATURE
Due to the high-speed nature of Andis clippers, please check for blade heat often, especially on close-cutting blades. If the blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade to maintain a comfortable temperature; using multiple blades of the same size is popular among groomers.

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it’s a sure sign blades need oil. The clipper should be held in the position shown in Figure F to prevent oil from getting into the motor. Place a few drops of Andis Clipper Oil on the front and side of the cutter blades (Figure G). Wipe excess oil off the blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to prevent injury.

You can clean the excess hair from your blades by using a small brush or worn- out toothbrush. To clean the blades we suggest immersing the blades only into a shallow pan of Andis Clipper Oil, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper off dry the blades with a dry cloth, and start clipping again.

If, upon cleaning your blades, you find the blades will still not cut, there may be a few fine pieces of hair trapped between the upper and lower blades. If this happens, you will need to snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the tension spring or moving the upper blade completely out from under the tension spring (Figure H). Wipe the surface between the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring (Diagram H). Now slide the upper blade to the opposite side of the lower blade and repeat this process. After completing this cleaning procedure, slide the upper blade, centering it over the lower blade. Hang or store your Andis clipper with the blades down so excess oil will not run into the clipper case.

FACTORY REPAIR SERVICE
When the blades of your Andis clipper become dull after repeated use, it is advised to purchase a new set of blades available through your Andis supplier or an Andis Authorized Service Station.

CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.
CAUTION: Never handle your Andis clipper while you are operating a water faucet and never hold your clipper under a water faucet or in water. There is a danger of electrical shock and damage to your clipper. The Andis Company will not be responsible in case of injury due to this carelessness.

MODEL MBG-2 (230V, 50Hz)
To find an Andis Authorized Service Station or access this manual online go to www.andis.com

©2013 Andis Company
1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A.
1-262-884-2600 www.andis.com info@andisco.com

Download PDF:Andis MBG-2 Easy Clip Groom Detachable Blade Clipper Kit User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals