Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit User INSTRUCTIONS
- March 21, 2024
- Andis
Table of Contents
Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit
Please read the following instructions before using your new Andis clipper. Give it the care that a fine, precision-built instrument deserves and it will give you years of service.
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be
followed, including the following: Read all instructions before using the
Andis clipper.
DANGER: To reduce the risk of electric shock:
- Do not reach for an appliance that has fallen into the water. Unplug immediately.
- Do not use it while bathing or in a shower.
- Do not place or store appliances where they can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
- Always unplug this appliance from the electrical outlet immediately after using it.
- Unplug this appliance before cleaning, removing, or assembling parts.
WARNING : To reduce the risk of burns, fire electric shock, or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by Andis.
- Never operate this appliance if it has a damaged cord or earplugs, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to an Andis-authorized service station for examination and repair.
- Keep the cord away from heated surfaces.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not use this appliance with a damaged or broken blade or comb, as injury to the skin may occur.
- To disconnect turn the control to “off” then remove the plug from the outlet.
- WARNING: During use, do not place or leave the appliance where it may be (1) damaged by an animal or (2) exposed to the weather.
- For trimming purposes only.
SAVE THESE INSTRUCTIONS
THIS PRODUCT INTENDED FOR HOUSEHOLD USE
To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.
OPERATING INSTRUCTIONS
Before starting the clipper, remove the blade guard (some models may not have a blade guard). Plug the cord into an electrical outlet, and operate at 120 volts, 60 cycle AC electrical current or as noted on the unit. To start the clipper, move the switch button to the ON position. To stop the clipper, move the switch button back to its original position. After using your clipper, rewrap the cord and store it in a safe place.
CLIPPING GUIDE
Description| Clipping Direction| Approximate Length of Cut| Blade set to
shortest cut| Blade set to longest cut
---|---|---|---|---
Standard Andis Blade| With hair grain| Against hair grain| 1/16” (1.6 mm)|
1/32” (0.8 mm)
| | | 3/16” (4.8 mm)| 1/8” (3.2 mm)
1/8” Attachment Comb| With hair grain| Against hair grain| 1/4” (6.4 mm)| 1/8”
(3.2 mm)
| | | 3/8” (9.5 mm)| 1/4” (6.4 mm)
1/4” Attachment Comb| With hair grain| Against hair grain| 3/8” (9.5 mm)| 1/4”
(6.4 mm)
| | | 1/2” (12.7 mm)| 3/8” (9.5 mm)
3/8” Attachment Comb| With hair grain| Against hair grain| 1/2” (12.7 mm)|
3/8” (9.5 mm)
| | | 5/8” (15.9 mm)| 1/2” (12.7 mm)
1/2” Attachment Comb| With hair grain| Against hair grain| 5/8” (15.9 mm)|
1/2” (12.7 mm)
| | | 7/8” (22.2 mm)| 5/8” (15.9 mm)
USING ATTACHMENT COMBS
(Some models do not have combs and sizes will vary by kit)
You can set the blades for a coarser cut by attaching any of the snap-on
attachment combs made for your clipper. The attachment combs mount easily–they
snap on and off (Figures A & B). These attachment combs guide hair into the
clipper blades and give you precise control of hair lengths. The length of
trim is indicated on the comb: 1/8″, 1/4″, 3/8″, and 1/2″. Use the clipping
guide to find the approximate lengths of the cut. Different blade angles about
the skin, thickness, and texture of the hair will vary the cutting length.
USER MAINTENANCE
The internal mechanism of your motor clipper has been permanently lubricated by the factory. Other than the recommended maintenance described in this manual, no other maintenance should be performed, except by Andis Company, or an Andis-authorized service station. To contact Andis directly, please call our Customer Support Team at 1-800-558-9441 or email us at support@andisco.com.
-
REMOVING BLADE SET
To remove the blade set, first, make sure your clipper is switched OFF and UNPLUGGED. Push down on the blade, then gently pull the blade forward (Figure C), and slide it off the blade hinge. If your blade hinge should snap closed and flush with the clipper, use a small standard screwdriver to pry the tongue of the hinge out (Figure D).
NOTE: Hair may accumulate in the front cavity of the housing under the blade. If this happens, you can clean out the hair by brushing out the cavity with a small brush or an old toothbrush while the blade is off the clipper. -
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure E) and with the clipper turned ON, push the blade towards the clipper to lock into position. -
BLADE TEMPERATURE
Due to the high-speed nature of Andis clippers, please check for blade heat often, especially on close-cutting blades. If the blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade to maintain a comfortable temperature; using multiple blades of the same size is popular among groomers. -
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down, it’s a sure sign blades need oil. The clipper should be held in the position shown in Figure F to prevent oil from getting into the motor. Place a few drops of Andis Clipper Oil on the front and side of the cutter blades (Figure G). Wipe excess oil off the blades with a soft dry cloth. Spray lubricants contain insufficient oil for good lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to prevent injury. You can clean the excess hair from your blades by using a small brush or a worn-out toothbrush. To clean the blades we suggest immersing the blades only into a shallow pan of Andis Blade Care Plus, while the clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After cleaning, turn your clipper OFF dry the blades with a dry cloth, and start clipping again.
If upon cleaning your blades you find that the blades will still not cut, there may be a few fine pieces of hair trapped between the upper and lower blades. If this happens, you will need to snap the blade off the clipper. Proceed to slide the upper blade to one side, without loosening the tension spring or moving the upper blade completely out from under the tension spring (See Figure H for the position of the blade). Wipe the surface between the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and also in the guide slot of the tension spring (Figure H). Now slide the upper blade to the opposite side of the lower blade and repeat this process. After completing this procedure, slide the upper blade, centering it over the lower blade. Handle or store your Andis clipper with the blades down so excess oil will not run into the clipper case. -
CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade currently being used may be dull), it could be that your blade drive assembly needs replacement. Please contact an Andis- authorized service station for a replacement. -
SERVICING OF A DOUBLE-INSULATED CLIPPER
In a double-insulated clipper, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated clipper, nor should a means for grounding be added. Servicing a double-insulated clipper requires extreme care and knowledge of the system, and should be done only by an Andis authorized service station. Replacement parts must be identical to those parts being replaced. A double-insulated clipper is marked by the words “double insulation” or “double insulated”. The symbol may also be marked on the appliance. -
BLADE & CLIPPER/TRIMMER REPAIR SERVICE
When the blades of your Andis clipper become dull after repeated use, it is advised to purchase a new set of blades available through your Andis supplier or through an Andis authorized service station (not all blades are available for purchase). If you wish your clipper to be serviced as well, it should be carefully packed and mailed either Parcel Post Insured or U.P.S. to any Andis authorized service station.
To contact Andis directly, please call our Customer Support Team at 1-800-558-9441 or email us at support@andisco.com.
CAUTION: Never handle your Andis clipper while you are operating a water faucet, and never hold your clipper under a water faucet or in water. There is a danger of electrical shock and damage to your clipper. Andis Company will not be responsible in case of injury due to this carelessness.
MANUFACTURER’S 12 MONTH LIMITED WARRANTY
This Andis product is warranted against defective material or workmanship for 12 months from the date of purchase. All express and implied warranties arising out of and applicable to the product by State law shall also be limited to 12 months from the date of purchase. Any Andis product determined by Andis to be defective in material or workmanship during the warranty period will be repaired or replaced, at Andis’ sole discretion, without cost to the consumer for parts and labor. To qualify for this limited warranty, the defective product must be returned via parcel post insured or U.P.S., with proof of purchase to Andis, 1800 Renaissance Blvd., Sturtevant, WI 53177 USA. Please include a letter describing the nature of the problem. Due to foreign matter sometimes found in hair and for other reasons, clipper blades or the resharpening of blades are not subject to this limited warranty. Andis will not be responsible for the replacement, cost of repairs, or alterations made to its products by any other person, agency, or company. Except as stated above, Andis does not provide and expressly disclaims any implied warranty of merchantability or fitness for a particular purpose or any other warranty of any kind whatsoever. Under no circumstances will Andis be responsible for incidental or consequential damages of any type, or any liability arising out of the use of unauthorized attachments. Some states may not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
- Date Purchased ___
- Model__
To find an Andis Authorized Service Station near you log on to andis.com or contact our customer service department: at 1-800-558-9441
WARNING: NO WARRANTY IF PURCHASED FROM UNAUTHORIZED SELLERS OF ANDIS
PRODUCTS
To ensure you are receiving an authentic, safe, quality product, you must
purchase Andis products only through authorized sellers.
Log on to andis.com or contact our customer service
department at 1-800-558-9441 (U.S.) to review a list of our authorized
sellers. These sellers are approved or certified by our company. If you do not
purchase through one of these companies, we cannot assure the authenticity or
condition of any Andis products, nor can we offer our warranty and related
services for any products purchased from an unauthorized seller. Any such
warranty is void and any warranty claim made for a product purchased from an
unauthorized seller will be denied. Any sale or use by these unauthorized
sellers of our products, and the marketing images, logos, trademarks, and
copyrighted material on our products, is also unauthorized.
© 2021 ANDIS COMPANY
1800 Renaissance Blvd. Sturtevant, WI 53177
1-800-558-9441 | info@andisco.com
FORM #103301
PRINTED IN USA
ANDIS.COM | SINCE 1922
FAQs
Is the Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit suitable for heavy-coated dogs like poodles?
Yes, this clipper kit is great for dogs with heavy coats like poodles, ensuring a neat and tidy grooming experience.
How does the Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit compare to other grooming clippers in terms of motor power?
The Andis MBG-2 clipper kit boasts a powerful motor that is perfect for complete animal grooming without the need for fans or air vents.
How can I adjust the cutting length of the Andis MBG-2 Clipper?
What is the recommended method for removing the blade set from the Andis MBG-2 Clipper?
To remove the blade set, ensure the clipper is switched OFF and UNPLUGGED. Push down on the blade, then gently pull the blade forward and slide it off the blade hinge.
How can I clean the cavity under the blade if hair accumulates there in the Andis MBG-2 Clipper?
You can clean out the hair accumulation by brushing the cavity with a small brush or an old toothbrush while the blade is removed from the clipper.
What should I do if the blade hinge of my Andis MBG-2 Clipper snaps closed?
If the blade hinge snaps closed and is flush with the clipper, you can use a small standard screwdriver to pry the tongue of the hinge out.
How can I ensure the blades of my Andis MBG-2 Clipper are properly lubricated?
Blades should be oiled before, during, and after each use with Andis Clipper Oil. A few drops should be placed on the front and side of the cutter blades, and excess oil should be wiped off with a soft dry cloth.
How long is the power cord of the Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit?
The Andis MBG-2 clipper kit features a 12-foot power cord, providing ample length for easy maneuverability during grooming sessions.
How does the Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit compare to other grooming clippers in terms of weight and ease of use?
The Andis MBG-2 clipper kit is lightweight and easy to handle, providing a comfortable grooming experience with its gentle blade motion and precise cutting.
What is the recommended maintenance procedure for the Andis MBG-2 Clipper?
The internal mechanism of the motor clipper has been permanently lubricated by the factory. No other maintenance should be performed except by Andis Company or an Andis-authorized service station.
How often should I check for blade heat on the Andis MBG-2 Clipper?
Due to the high-speed nature of Andis clippers, it's recommended to check for blade heat often, especially on close-cutting blades.
What should I do if my Andis MBG-2 Clipper blades still won't cut after cleaning?
If blades still won't cut after cleaning, there may be fine pieces of hair trapped between the upper and lower blade. In such cases, the blades should be removed, cleaned, and reassembled as per the provided instructions.
How long is the warranty period for the Andis MBG-2 Clipper?
The Andis MBG-2 Clipper is warranted against defective material or workmanship for 12 months from the date of purchase.
Download this Manual:Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit User INSTRUCTIONS
Reference Link
Andis MBG-2 7-Piece Detachable Ceramic Blade Clipper Kit User INSTRUCTIONS- Device. report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>