PYLE PW Series Active Powered Subwoofer Box System User Guide
- July 6, 2024
- Pyle
Table of Contents
PYLE PW Series Active Powered Subwoofer Box System User Guide
Features:
- DSP Digital Signal Processor
- Power-On and Signal Input LED Indicators
- Signal Input LED Indicator
- Clip Limiter Circuitry with LED Indicator
- Balanced XLR + TRS Input Jacks
- Balanced XLR Thru Output Jacks for Parallel Connections
- Passive Heat Sink with Fan for Cooling
- Subwoofer Crossover 80Hz/100Hz/120Hz/150Hz/200Hz Low Pass
- Subwoofer Level Adjustment
- Subwoofer Phase Control
- Built-in Pole Mount Socket
- Built-in Carrying Handles
- Custom Metal Grill
What’s in the Box:
- Wooden Subwoofer
- Power Cable
Technical Specs:
- Construction Materials: Wooden Painted Enclosure with MDF Board
- Power Supply: 450 Watts RMS / 900 Watts Program / 1800 Watts Peak Power
- Woofer: 12″
- Magnet: 70oz
- Voice Coil: 3”
- Frequency Response: (+/-3dB) 48Hz – 200Hz
- Maximum SPL: 127dB Peak / 124dB Continuous
- Product Dimensions: 13.78” x 20.87” x 20.47” -inches
Control Panel Layout
PW12SUBA PW15SUBA PW18SUBA
- Channel A volume control
- Ground and float switches
- Channel B volume control
- When the Bluetooth is turned on, the light flashes and lights up after connecting
- When the TWS is turned on, the light flashes and lights up after connecting
- Power LED indicator Signal LED indicator Limit LED indicator
- Low out for 80Hz/100Hz/150Hz /200Hz
- Phase switching switch
- A-channel balanced input A-channel balanced output
- B-channel balanced input B-channel balanced output
- Master Volume Control
- XLR balanced output
- PRE-output and mixed output(The pre-output is the main frequency, and the mixed output is the low frequency 120HZ excision)
- Fused LEC mains inlet
- Power Switch(ON/OFF)
- 110V/220V switch
FCC Warning
15.19 Labeling requirements. This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>