HOFTRONIC 5435911 Auto Detect Dimmer User Manual
- June 3, 2024
- HOFTRONIC
Table of Contents
HOFTRONIC 5435911 Auto Detect Dimmer
IMPORTANT SAFETY DETAILS
- Hazardous voltage may be present at the output of the dimmer despite setting the dimmer to zero brightness level. Look out and tag the input circuit before accessing the wiring connections. Failure to follow this warning can result in death or serious injury.
- Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
- This dimmer shall be protected by a 6A or up to a 10A maximum miniature circuit breaker, which is special use with this dimmer.
- This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
- This product may NOT be installed by minors or people with a mental disability.
INSTALLATION DETAILS
ONE WAY OPERATION
MULTI WAY OPERATION
- Disconnect power. Lock out and tag the relevant circuit at the mains switchboard.
- Remove existing switch from wall.
- Connect the dimmer in accordance with the wiring diagrams.
- the copper conductors for the terminals is 1,0 to 1,5mm rigid wire.
- Refit switch plate to wall and fit the dimmer knob to the shaft.
- Reconnect power. Push ON and dim with turning knob.
NOTE:
The Dimmer must always be connected to the LINE side of the load. Multi-way
retractive switch or push switch can control up to 20 units for UP/DOWN dim
and ON/OFF function. Two or more dimmers MUST NOT be connected in parallel or
series to control the same load from two different locations.
ELECTRICAL SPECIFICATIONS
| PARAMETER | VALUE |
|---|---|
| Supply voltage & Frequency | 220-240V ~ 50Hz |
| Dimming technology | Auto Detect Trailing/Leading edge driven control. Leading |
edge dimming mode can be set by user manually.
Rating| 10-100W: incandescent lamps, high voltage halogen lamps and electronic
step-down converter for extra low-voltage incandescent lamps.
3-250W: dimmable LED lamps.
Compatible loads| Dimmable LED lighting with compatible Electronic
Transformers Incandescent lighting, MV Halogen lamps LV Halogen Lighting with
electronic transformers LV Halogen Lighting with iron core transformers
Operating Temperature| 0°C – 35°C
Operating Humidity| 10 – 90% R.H.
Mounting Centres| 82mm EU Pattern Plate
NOTE:
Operation at elevated temperatures or voltages may cause the thermal
protection circuit to operate. If this happen, decrease the connected load to
prevent re-occurance.
MINIMAL BRIGHT LEVEL SETTING
HOW TO SET THE MINIMUM BRIGHT LEVEL:
Adjust the required minimum brightness then short press 5x within 5 seconds to
save a minimum level, your LED lighting will flash 3 times.
HOW TO RESET THE MINIMUM BRIGHT LEVEL:
Short press 7x within 5 seconds to reset the minimum level, your LED lighting
will flash 3 times. Adjust to required minimum brightness and short press 5x
within 5 seconds to save minimum level, your LED lighting will flash 3 times.
Each step must be performed within 15 seconds, if not, it will time out and go
to the auto exit program without saving.
FEATURES
- Suitable for 1-way of multi-way full dimming and switching.
- Minimum load down to 3W of capacitive or restistive load, such as dimmable LED Lighting, Incandescent Lighting, MV Halogen/LV Halogen Lighting with electronic transformers.
- Lamps soft start operation, to extend longer lifetime for the lamp.
- LED back light for indication of the dimming mode.
- User setting for the minimum dim level.
- Build in short circuit protect, designed to ensure the dimmer can survive in case of wiring fault or catastrophic failure of the load.
- Build in resettable thermal cut-off to protect the dimmer over normal operation temperature caused by overloads.
NORMAL OPERATION
Operation of dimmer knob and push switch:
Push knob ON or push knob OFF or hold the knob to
dim. Turn the knob clockwise to increase brightness. Turn the knob anti-
clockwise to reduce brightness.
NOTE:
When connect with iron core transformers, only leading edge mode (LE) could be
applied, the TE mode can not be used in this case. Multiple compatible loads
can be used as the total lamp wattage does not exceed the maximum load rating
of the dimmer. Some lamps may exhibit unexpected performance characteristics
when cold. Dimming performance should improve after the lamp warms up. Or in
case of lamp appears unstable status, it could be changed to TE or LE mode.
INTENDED USE / APPLICATION
Product designed for the use in households and for other similar general applications.
MOUNTING
Technical changes reserved. Read the manual before mounting. Mounting should
be performed by an appropriately qualified person. Any activities to be done
with
disconnected power supply. Exercise particular caution. Product has a
protective contact/terminal. Failure to connect the protective lead may lead
to electric shock. Mounting diagram: see pictures. Check for proper mechanical
fastening and connection to electrical power prior to first use. The product
can be connected to a supply network which meets energy quality standards as
prescribed by law. To maintain the proper IP protection level, the right
diameter of the power cable should be selected for the cable gland used in the
product.
FUNCTIONAL CHARACTERISTICS
Product can only be used indoors.
USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and
the product has cooled down. Clean only with soft and dry cloths. Do not use
chemical detergents. Do not cover the product. Ensure free air access. Product
may heat up to a higher temperature. Product can only be supplied by rated
voltage or voltage within the range provided. It’s forbidden to use the
product with damaged protective cover. Product must not be used in
unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air
atmosphere, fumes, or chemical fumes, etc. Non-demountable product. Not
suitable for independent repairs.
ENVIRONMENTAL PROTECTION
Keep your environment clean. Segregation of post-packaging waste is
recommended. This labelling indicates the requirement to selectively collect
waste electronic and electrical equipment. Products labelled in this way must
not be disposed of in the same way as other waste under the threat of a fine.
These products may be harmful to the natural environment and health, and
require a special form of recycling/neutralising. Products labelled in this
way should be returned to a collection facility for waste electrical and
electronic goods. Information on collection centres is provided by local
authorities or sellers of such goods. Used items can also be returned to the
seller when new product is purchased, in quantity no larger than the purchased
item of the same type. The above rules regard the EU area. In the case of
other countries, regulations in force in a given country must be applied.
Contacting the distributor of our products in a given area is recommended.
COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns,
electrical shock, physical injury and other material and non-material damage.
For more information about Hoftronic products visit www.hoftronic.com.
Hoftronic shall not be responsible for any damage resulting from the failure
to follow these instructions. Hoftronic reserves the right to make changes in
the manual – the current version can be downloaded at
www.hoftronic.com.
DECLARATION OF CONFORMITY
DOCUMENTATION
This product has been manufactured and supplied in compliance with all
relevant regulations and directives applicable to all member states of the
European Union. The product complies with all applicable regulations and rules
in the country of sale. Formal documentation such as the declaration of
conformity, the safety data sheet and the product test report is available
upon request.
CE DECLARATION
The product complies with the following directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon
request.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>