SEAFLO SFSP1-G200-03B Submersible and Inline Pump Instruction Manual
- July 4, 2024
- SEAFLO
Table of Contents
SEAFLO SFSP1-G200-03B Submersible and Inline Pump
Specifications
- Model: SFSP1-G200-03B
- Voltage: 12V
- Max Draw: 4.5A
- Head: 5m / 16.4′
- Flowrate: 200GPH
- Duty Cycle: Intermittent 2/5
- Outlet Diameter: 11mm & 1/2 (13mm)
- Pumping Liquid: Water
Product Usage Instructions
Installation
The Submersible Inline Pump can be used as a flooded suction water supply
pump or as an inline booster pump
Operation
- As the In-Line Booster pump is not self-priming, prime the system using a hand pump, foot pump, or gravity.
- When fully immersed in water, the inline pump is primed and delivers water instantly.
Maintenance
To protect against damage during winter, drain the water when
the pump is not in use.
Before Usage
- Ensure efficient operation and maximum pump life by following points:
- To avoid trapped air inside the pump and ensure successful priming, place the pump in water and shake for a few seconds horizontally or inverted before switching it on. Repeat after refilling the water tank.
- To prevent air leaks, securely fasten the hoseconnections.
DESCRIPTION
The Submersible Inline Pump is able to function as a flooded suction water supply pump or as an inline booster pump. It is able to pump clean water or diesel.
INSTALLATION
Use suitable size of hose (check outlet dia of technical data below) to
connect to the pump, use adaptor when you need it.
Note: Ensure that the adaptors are pressed on firmly. Once fitted the
adaptors cannot be removed. Install a check valve in the pipe when there is a
long run of pipe between pump and faucet.
The In-line Booster Pump must be installed in the following ways:
- 1. The position of the pump is lower than the water tank, and pump the oil or water;
- 2. In conjunction with:
- a) a hand-operated pump
- b) a foot operated pump
- c) in-line to boost another pump Notes:
- Position the In-Line Booster pump in the suction pipe between the foot pump and the water tank, not between the foot pump and faucet.
- The In-Line Booster pump is light enough to suspend in the pipework.
- The In-Line Booster Pump is a sealed unit and can be submersed in water.
OPERATION
- As the In-Line Booster pump is not self-priming, it is necessary to prime the system with either: a hand pump, a foot pump, by gravity.
- When fully immersed in water the inline pump is primed and gives instant delivery of water.
CAUTION
- Do not pump water above 60°C (140°F), or below 0°C (32°F).
- Do not pump diesel above 50°C (122°F).
- The pump is suggested to be installed vertically.The pump outlet should be higher than the inlet, if possible.
- The duty cycle of the pump is continues.o
MAINTENANCE
To protect against damage during the winter, drain the water when the pump is not using.
BEFORE USAGE
For efficient operation and maximum pump life, note the following points:
- a) In order to avoid the trapped air inside the pump and to ensure the successful priming, place the pump in water and shake for a few seconds in a horizontal or inverted position before switching the pump on. (This action should be repeated after refilling the water tank.)
- b) In order to avoid air leaks, securely fasten the hose connections.U
TECHNICAL DATA
Model| Voltage| Max Draw| Head| Flow rate| Duty Cycle| Outlet Dia| Pumping
Liquid
---|---|---|---|---|---|---|---
SFSP1-G200-03B| 12V| 4 . 5A| 5m / 16.4′| 200GPH| Intermittent|
2/5″(11mm)&1/2″(13mm)| Water
SFSP1-G280-02A| 12V| 4.5A| 7m / 23′| ****
280GPH
| ****
Intermittent
| ****
1/2″(13mm)
| ****
Water, Diesel
SFSP1-G280-02B
SFSP1-G500-02A SFSP1-G500-02B| 12V| 4.5A| 7m / 23′| ****
500GPH
| ****
Intermittent
| 3/4″(20mm)| Water, Diesel
“A” refers to with clip and 5M cable. “B” refers to only 1M cable.
DIMENSION
Frequently Asked Questions
- Q: Can this pump be used with diesel?
- A: Yes, this pump is capable of pumping clean water or diesel as specified in the technical data section.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>