TRIBIT BTS33 Portable Wireless Speaker User Guide
- July 3, 2024
- Tribit
Table of Contents
TRIBIT BTS33 Portable Wireless Speaker
Product Information
Specifications
- Charging time: Approximately 2.5 hours
- Indicator lights: White light for low battery, red light for charging, no light when fully charged
Product Usage Instructions
Charging The Speaker
To charge the speaker, connect the charging cable to the speaker and a
power source. When the battery is lower than 20%, the white light on the power
button will blink. During charging, the red light of the charging indicator
will remain on. Once fully charged (about 2.5 hours), the red light will turn
off.
Power On/Off
To power on the speaker, press and hold the power button until it turns on.
To power off, press and hold the power button again until the speaker shuts
down.
Pairing
To pair the speaker with a device, ensure that the speaker is turned on and
in pairing mode. Enable Bluetooth on your device and search for available
devices. Select the speaker from the list of available devices to complete the
pairing process.
Frequently Asked Questions (FAQ)
-
Q: How long does it take to fully charge the speaker?
A: It takes approximately 2.5 hours to fully charge thespeaker. -
Q: What do the different indicator lights signify?
A: The white light indicates low battery, the red light indicates charging, and no light is displayed when the battery is fully charged.
TRIBIT
StormBox Mini
Portable Wireless Speaker
Hereby,
Thousandshores Deutschland GmbH declares that the radio equipment type
Portable Wireless Speaker BTS33 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration conformity is available at the following
internet address: http://files.tribit.com/BTS33-eu-doc.pdf
Learn more about the UK Declaration of Conformity, Please click below link to download http://files.tribit.com/BTS33-uk-doc.pdf
To Charging The Speaker
- When the battery is lower than 20%, the white light可the power button blinks.
- When charging, the red light of the charging indicator is always on.
- When fault)’charged (about 2.5 hours), the red light goes out.
Power On/Off
Short press the power button to turn on/off,
When there is no audio input or any operation, the speakers will automatically
turn off after 75 minutes,
Pairing
Short
press the Bluetooth button to enter pairing mode, the speaker can be ccnnected
to up to one device at the same time.
Press the Bluetooth button again to disccnnect the Bluetooth connection,
To Charging The Speaker
xl : Press once- x2 : Press twice
- x3 : Press three times
- 2s : Press and hold for 2 seconds
- Reset : Press and hold the +- button at the same time for 5s
To Charging The Speaker
Turn both speakers on:- Long press the Bluetooth button of Speaker A for 5s, and let go after hearing the voice announcement:
- Short press the Bluetooth button of Speaker B, then beth speakers will announce the voice at the same time to Indicate the success of stereo mode.
Note: stereo mode is not supported when using AUX input.
Safety Precautions
- Do not place the speaker in a place where it is easy to fall.
- Do not disassemble, repair or modify this product by you芯elf
- Keep 1ne speaker away from extreme temperatures.
- Do not use the speaker in an outdoor thunderstorm environment
- Do not use any corrosive cleaners or other chemical solutions to clean the speaker.
- 12-month warranty.
Specifications
- Bluetooth Version : V5.4
- Output Power : 2*5W
- Bluetooth Protocol: A2DP, AVRCP,HFP,HSP
- Frequency Response Range : 80~20KHz
- Frequency Band Range : 2402-2480MHz
- Maximum Transmission Power : <6dBm
- Battery: 2600mAh
- Play Time: 12 hours(At 60% volume)
- Charging Time: About 2.5 hours
- Waterproofing Grade: IPX7
- Size: 119mm X 91mm X 91mm
- Weight: 545g
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These mits are designed to provide reasonable protection against harmful nterference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures;
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
IC Caution
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The power delivered by the charger must be between min 0.75 Watts required by the radio equipment, and max 6 Watts in order to achieve the maximum charging speed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>