CHERY LIFE 10×13 ft Aluminum Pergola With Canopy Installation Guide
- July 2, 2024
- CHERY LIFE
Table of Contents
CHERY LIFE 10×13 ft Aluminum Pergola With Canopy Installation Guide
Product Description
HARDWARE
- P1
M6X15 Bolt 106 PCS
-
P2
Big Bolt 32 PCS -
P3
M6X70 Bolt 6 PCS
- P4
M6X40 Bolt 1 PC
-
R
Plastic Cap 113 PCS -
Ο
Nut Cap 1 PC -
Q
Nut 1 PC -
T
Ground stake 16 PCS -
Big Bolt Tool 1 PC
-
Tool 1 PC
-
M6 Bolt Tool 1 PC
Parts
-
Post 1
2 PCS -
Post 2
2 PCS -
Post 3
4 PCS -
post top cap
4 PCS -
Drawstring glide wheel with magnet
1 PC -
Middle cross beam
2 PCS -
Bottom cross beam 1
2 PCS -
Bottom cross beam 2
2 PCS -
Side cross beam 1
2 PCS -
Side cross beam 2
2 PCS -
Enhanced support beam
4 PCS -
Bottom cross beam 3
1 PC -
Triangle cap
10 PCS -
post connector
4 PCS -
post middle decorative circle
4 PCS -
Fabric rib 1
12 PCS -
Fabric rib 2
6 PCS -
side glide wheel
12 PCS -
Enhanced support beam connector
2 PCS -
Middle &side cross beam connector
3 PCS -
Stake piece
4 PCS -
Gripping magnet steel piece
1 PC -
fabric cover
1 PC -
middle glide wheel
5 PCS -
Bottom cross beam connector
4 PCS -
Triangle cap
4 PCS
Installation Instruction
-
Attach post top cap (A) to post (1 & 2)
-
Attach and fasten stake piece (U) to the end of post (3) by bolt (P1) and cap (R)
-
Insert post connector (J) into post (3) by bolt (P1) and bolt cap (R)
-
Attach decorative circle (K) to post (3), and attach post (1 & 2) to post (3) by bolt (P1) and bolt cap (R)
-
Connect two middle cross beams (C) with inside connector (N1) by bolt (P1) & bolt cap (R) to make sure that there is no gap between the two middle cross beams (C) by righting the bolts
-
“Assemble 5 pcs of middle glide wheels (Y) and drawstring glide wheels with magnet (B) into middle cross beam (C). Separate the middle glide wheels (Y) by using bolt (P4) & nut (Q) & bolt cap (R) & nut cap (O)
Attention : please joint two tubes together without gap and then assemble the screws” -
Attach triangle cap (G) to assembled middle cross beam (C)
-
Assemble six side glide wheels (M) into side cross beam (E), and then connect side cross beam 1 (E) & side cross beam 2 (E1) with inside connector (N1) by bolt (P1) & bolt cap (R) to make sue there is no gap between the two tubes by righting the bolt.
-
Attach triangle cap (G) to side cross beam 1 & 2 (E & E1)
-
Connect bottom cross beam 1 (D) and bottom cross beam 2 (D1) & beam 3(D3) with inside connector (N2) by bolt (P1) & bolt cap(R) to make sue there is no gap between the two tubes by righting the bolt. Make sure the bottom cross beam 1 & 2 (D & D1 & D3) is in the same direction
-
Attach triangle cap (G) to assembled bottom cross beam (D & D1)
-
Connect bottom cross beam 1 (D) and bottom cross beam 2 (D1) & beam 3 (D2) with inside connector (N2) by bolt (P1) & bolt cap (R)to make sue there is no gap between the two tubes by righting the bolt. Make sure the Make sure the bottom cross beam 1 & 2 (D & D1 & D2) is in the same direction
-
Attach triangle cap (G) to assembled bottom cross beam (D & D1)
-
Connect two enhanced support beams (F) with inside connector (N2) by bolt (P1) & bolt cap (R) to make sue there is no gap between the two tubes by righting the bolt
-
Attach triangle cap (G) to assembled enhanced support beam (F)
-
Connect assembled side cross beam (E1) and assembled bottom cross beam 2 (D1) to assembled post (2) by big bolt **(P2)
**
-
Follow the same step as 14 to connect other three left
-
3 Attach assembled middle cross beam (C) to assembled bottom cross beam (D & D1 & D2) by bolt (P3) & bolt cap (R)
-
Attach assembled enhanced support beam (F) to assembled bottom cross beam (D & D1) by bolt (P3) & bolt cap (R)
-
Insert fabric rib 1 (L) into fabric rib 2 (L 1), and then through assembled fabric rib 1 (L) into fabric cover (W), and through assembled fabric ribs (L) into the hole of glide wheel (Y &B)which on assembled middle cross beam (C)
-
Connect assembled fabric rib 2 (L1) to the hole of glide wheel (M) which on assembled side cross beam (E) by bolt (P1) & bolt cap (R)
-
Attach gripping magnet steel piece (V) into assembled bottom cross beam 3 (D2) by bolt (P1) & bolt cap (R
-
Connect drawstring of drawstring glide wheel with magnet (B) to gripping magnet steel piece (V). Fix assembled pergola on the ground with ground stakes (T) if needed.