VIMAR 46239.040A PT Wi-Fi Camera User Guide
- June 30, 2024
- VIMAR
Table of Contents
VIMAR 46239.040A PT Wi-Fi Camera
Specifications
- Ambient microphone to hear surroundings
- SD card slot for recording (max 128 GB)
- Reset the button to restore the initial values
- Micro SD card insertion
- Status LED
- Power supply connector
Product Usage Instructions
Installation
Place the camera on a flat surface or use the fixing bracket for
ceiling mounting. Avoid backlight or excessive light conditions to
prevent overexposed images.
Configuration
Powering up the camera
- Connect the USB cable to the power port on the camera.
- Connect the power supply to a wall socket.
- Wait for the LED status to flash, indicating the camera is on and in setup mode.
Installing the App on the smartphone
Download and install the Vimar VIEW Product App from your App Store.
Package content
Characteristics
Status LE
- Red light on = Network anomaly.
- Flashing red light = waiting for the network to connection (slow blinking), connecting to the network (fast flash).
- The blue light on = the camera is working correctly.
- Blinking blue light: awaiting manual WiFi configuration, or currently connecting (faster blinking).
Reset Button:
Press and hold for 5 seconds to reset the camera to the initial values.
Installation
Positioning
Place the camera firmly on a flat surface or use the fixing bracket for
ceiling mounting.
Installation Notes:
To prevent overexposed images, avoid installing the camera under backlight
or excessive light conditions.
Configuration
Power up the camera
- Connect the USB cable to the power port on the camera.
- Connect the power supply to a wall socket.
- Wait for the LED to status flashes, you will hear spoken feedback (“Camera ON” and then“ Camera setup ”).
4.2 – Install the App on the smartphone
Download the Vimar “VIEW Product” App and install it on your smartphone,
searching for it directly in your reference App Store.
4.3 – First access
- If you already have an account for MyVIMAR, open the App and log in with your credentials.
- If not, create a new account, by tapping on the dedicated link “Create a new account”.
- Follow the next instructions in the App, enter your credentials, and proceed from step
Adding a camera
- Follow the instructions on the screen to complete installation and connection to your router.
- To make this process easier, we recommend you stay close to your router.
In addition via QR Code
use the camera to scan the QR code displayed on your smartphone.
N.B
after the camera is switched on, the status LED lights up. After the
acoustic signal, the device LED flashes quickly.
Tap “Add device + 1 Select model 2 Enable the next step, and continue by
following the instructions on the screen 3 Set the Wi-Fi for device 4 and
continue with the procedure to display the QR code.
A QR code will be displayed on your smartphone, turn the screen on your phone to face the camera at a distance of between 15 – 20 cm from the lens, and a tone will be emitted after a few seconds, tap on “Tone Emitted” (refer to the images below).
Wait for the connection to be completed, after a few seconds the device will be successfully added and emit the spoken feedback “Online”.
ATTENTION
to safeguard your data and the security if you intend to add the same
camera via another account, you need to cancel the camera from the App where
it is associated, in case of return of the product, is recommended in addition
also to remove the SD card.
The camera is also compatible with the application Smart Life.
For more information see the complete manuals and updated available in the
product sheet on the site: https://faidate.vimar.com/it/it
Specifications
Power supply Specifications
Operation disclaimer for Wi-Fi cameras
The Wi-Fi camera allows images to be viewed on the buyer’s (hereinafter
“Customer”) smartphone and/or tablet, by simply installing the Vimar VIEW
Product application.
The visualization of the images is allowed only through the presence, in the
house/building in which it is installed, of a connection to a home Wi-Fi
network with Internet access which must have the following characteristics:
• IEEE 802.11 b / g / n (2.4 GHz) standard
• Frequency range: 2412-2472 MHz
• Transmitted RF power: <100mW (20dBm)
Operating modes:
• Networks: WEP, WPA and WPA2.
• TKIP and AES encryption protocols are supported for WPA and WPA2 networks.
• Do not support “hidden” networks (hidden SSID).
To use the service The Customer must have technical equipment that allows
connection to the Internet and sign an agreement with an ISP (Internet Service
Provider); this agreement may involve related costs. Vimar remains unaffected
by the choice of technical equipment and the agreement with the ISP (Internet
Service Provider). The consumption of data through the use of the Vimar VIEW
Product App, both in the home/building and outside the Wi-Fi network that the
Customer has used for installation, remains the responsibility of the
Customer.
The interaction and correct operation remotely via the Vimar VIEW Product App,
through the Internet network of your mobile phone/data provider, with the Wi-
Fi camera installed by the Customer may depend on:
- type, brand, and model of the smartphone or tablet;
- quality of the Wi-Fi signal;
- type of the home internet access contract;
- type of data contract on the smartphone and tablet.
The camera supports connection via P2P technology, it is therefore necessary
to check that your ISP (Internet Service Provider) does not block it.
Vimar is exempt from any liability for any malfunctions due to non-compliance
with the minimum technical specifications necessary for the operation of the
product which is indicated above. To resolve any problems, refer to the
complete manual and the “Questions and answers” section on the product page at
the following Internet address:
faidate.vimar.com. Vimar reserves the right to
modify the characteristics of the products shown at any time and without
notice.
Conformity
RED directive. RoHS directive
Standards EN 301 489-17, EN 300 328, EN 62311, EN 62368-1, EN 55032, EN 55035,
EN 61000-3-2, EN 61000-3-3, EN IEC 63000.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces
of lead.
Vimar SpA declares that the radio equipment complies with Directive
2014/53/EU. The full text of the EU declaration of conformity, the instruction
manual, and the configuration software are on the product sheet available at
the following Internet address faidate.vimar.com
WEEE – Information for users
If the crossed-out bin symbol appears on the equipment or packaging, this
means the product must not be included with other general waste at the end of
its working life. The user must take the worn product to a sorted waste
center, or return
it to the retailer when purchasing a new one. Products for disposal can be
consigned free of charge (without any new purchase obligation) to retailers
with a sales area of at least 400m2 if they measure less than 25cm. An
efficient sorted waste collection for the environmentally friendly disposal of
the used device, or its subsequent recycling, helps avoid the potential
negative effects on the environment and people’s health and encourages the re-
use and/or recycling of the construction materials.
Privacy Policy
As required by Regulation (EU) 2016/679 on the protection of personal data,
Vimar S.p.A. guarantees that the electronic processing of data minimizes the
use of personal and other identification information, which is only processed
to the extent strictly necessary to achieve the purposes for which it was
collected. The personal information of the Data Subject is processed by the
product/application privacy policy available on our website
www.vimar.com in the legal section (Product – App
Privacy Policy – Vimar energia positiva).
Please remember that under Regulation (EU) 2016/679 on the protection of
personal data, the user is the controller of processing the data collected
during the use of the products and, as such, is responsible for adopting
suitable security measures that protect the personal data recorded and stored,
and avoid its loss.
Should the camera monitor public areas, it will be necessary to display – in a
visible manner – the information about the ‘area under video surveillance’
envisaged in the privacy policy and specified on the website of the Italian
Data Protection Authority (Garante). The recordings may be stored for the
maximum period envisaged by legal and/or regulatory provisions in the place
where the camera has been installed. If the regulations in force in the
country of installation envisage a maximum storage period for the image
recordings, the user shall ensure they are deleted in compliance with the
applicable regulations.
In addition, the user must guarantee safe possession of and control over its
passwords and the related access codes to its web resources. The Data Subject
must provide the password for access to its system when requesting help from
the Vimar Support Centre so that the related support can be provided.
Provision of the password represents consent for processing. Each Data Subject
is responsible for changing the password for access to its system on
completion of the work carried out by the Vimar Support Centre.’
49401499A0 06 2405
Viale Vicenza, 14 36063 Marostica VI – Italy
www.vimar.com
FAQ
What do the different LED status lights indicate?
Red light: Network anomaly
Flashing red light: Waiting for network connection or connecting
Blue light: Camera working correctly
Blinking blue light: Awaiting manual WiFi configuration or currently
connecting
How do I reset the camera to its initial values?
Press and hold the reset button for 5 seconds.
References
- Canale Fai da te
- Home automation, electrical equipment, smart home - Vimar energia positiva
- Canale Fai da te
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>