Metra 1995-2011 Ford Multi Kit Installation Guide

June 29, 2024
Metra

Metra-logo

Metra 1995-2011 Ford Multi Kit

Product Information

Specifications

  • Product Name : Double-DIN Receiver Installation Kit
  • Model Number : 120 95-5817
  • Compatibility : Designed for vehicles using the 120 95-5817 installation kit

Product Usage Instructions

Modifications for Double-DIN Receiver Installation:

  1. Permanent modifications are required to fit a Double-DIN receiver into the dash of compatible vehicles.
  2. Removal of dash material is necessary, but caution should be taken not to remove excessive material.
  3. It is recommended to remove portions gradually, testing the fit as you progress.

Installation Steps

  1. Using a file or rotary tool, carefully remove portions from the top and bottom rim of the dash opening.
  2. Ensure a proper fit is achieved before proceeding with the complete receiver installation.
  3. Complete the receiver installation following the instructions provided with the 120 95-5817 installation kit.

Additional Notes

  • Test fit using the receiver only without the side brackets in place.
  • If the receiver is fully snapped into place, it cannot be removed without removing the dash panel.

Tools Required
File or Rotary Tool

Important Safety Information:

CAUTION: Always exercise caution when cutting or drilling in a vehicle. Wear eye protection and be mindful of wiring, windows, fuel lines, and safety devices. Check drilling depth and location to prevent damage to the vehicle’s appearance.

FAQ

  • Q: What should I do if I accidentally remove too much material from the dash?

    • A: If excess material is removed, it is recommended to consult a professional installer for further assistance.
  • Q: Can the factory unit be reinstalled after making modifications for the Double-DIN receiver?

    • A: Once modifications are made, the factory unit may not properly fit if reinstalled. It is advisable to consider this before proceeding with the modifications.

120 95-5817 Supplemental Instructions for Double-DIN Receiver Applications

120 95-5817I

Permanent modifications will be necessary in order to allow a Double-DIN receiver to fit into the dash of vehicles that use the 120 95-5817 installation kit. Removal of dash material is required. Once modifications are made, the factory unit may not properly fit if reinstalled.

Notes

  • Do not remove too much material. It is better to remove portions and measure or test fit as you go.
  • Test fit using the receiver only. The side brackets should not be in place. If the receiver is fully snapped into place, it cannot be removed without the dash panel being removed.
  1. Using a file or rotary tool, carefully remove portions from the top and bottom rim of the dash opening as shown.
  2. Once a proper fit is achieved, complete receiver installation following instructions supplied with the 120 95-5817 installation kit.

Metra-1995-2011-Ford-Multi-Kit-image \(1\)

1-800-955-9094
TECHNICAL SUPPORT

CAUTION
Always be careful when cutting or drilling in a vehicle. WEAR EYE PROTECTION. Be aware of things such as wiring, windows, fuel lines and safety devices. Check drilling depth and location to avoid damage to vehicle appearance.

Installation instructions for part 95-5817

Ford multi-kit 1995-2011 95-5817

Kit Features
SO DDIN radio provision

Note

  • Sub-dash modifications are necessary to use this dash kit. You will need to trim the sub-dash to gain suitable depth and height.
  • Once the kit is snapped in, it cannot be removed without dash panel removal.

Kit Component

  • A) ISO DDIN brackets
  • B) Filler bar

See application list inside cover

Wiring And Antenna Connections (sold separately)

Wiring Harness
Please visit metraonline.com for wiring harness options

Antenna Adapter
Not required

Tool Required

  • Dremel/Cutting tool
  • Metra 86-5618 removal keys

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

Dash Disassembly

All vehicles

  1. Using the Metra 86-5618 removal keys, slide the radio out of the radio cavity. Unplug and remove the radio.
  2. Cut and remove obstructions in dash cavity. ATTENTION: Be careful not to cut into harnesses or electronic components.

Continue to kit assembly

Kit Assembly

ISO DDIN radio provision

  1. Attach the ISO DDIN brackets to the radio using the screws supplied with the radio. (Figure A)
  2. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Test the radio for proper operation.
  3. Slide the completed assembly into the modified sub-dash until it clicks into place.
  4. Clip the filler bar into the bottom of the radio opening under the radio assembly with the rounded edges facing toward the dash. Tip: Hook one side in then push the other side in until it clips. (Figure B)

CAUTION: ONCE THE KIT IS SNAPPED IN, IT CANNOT BE REMOVED WITHOUT DASH PANEL REMOVAL.

IMPORTANT
If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

  • metraonline.com
  • METRA. The World’s best kits.™
  • © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals