HOFTRONIC 5422317 12V Dimmable Driver User Manual

HOFTRONIC 5422317 12V Dimmable Driver

INSTALLATION MANUAL

How to install the dimmable LED Driver

1. Switch off the main power.
2. Connect the dimmable LED driver to 230V (INPUT) main power. Please look careful at the color of the wires whereby N should be connected to the blue wire & L should be connected to the brown wire. You can make sure to connect an ON/OFF switch or a power cord (fixed mains current) on the driver to power ON/OFF the LED driver easily.
3. If the transformer will be installed outdoors, the LED driver must be installed inside of a water / moisture resistant housing/junction box (ART. NO. 396302 or 4409418).
4. The recessed spots can only be used as recessed spots in a covered area outside or in areas where there is moist. Optionally, the set can be expanded with a touch wall dimmer 2.4 Ghz.

Follow the steps below to connect the remote control to the dimmable LED driver

1. Turn on the light on the driver by switching the power on via the wall switch or plug in the power cord to the mains power. Immediately press the Z1 or Z2 within 5 seconds of the power being turned on. Then you can see the spot light(s) flashing one single time, which means that the remote is connected to the driver.
   When the remote is not connected successfully the first time, pay attention to the following:
   Make sure that you press and hold the Z1 or Z2 button for 5 seconds, do not click several times!

2. Make sure that the red light on the remote is burning while you are pressing and holding the Z1 or Z2 button.

3. The spotlights should flash one time which means that the driver and remote have been connected correctly.

INTENDED USE / APPLICATION

Product designed for the use in households and for other similar general applications.

MOUNTING

Technical changes reserved. Read the manual before mounting. Mounting should be performed by an appropriately qualified person. Any activities to be done with disconnected power supply. Exercise particular caution. Product has a protective contact/terminal. Failure to connect the protective lead may lead to electric shock. Mounting diagram: see pictures. Check for proper mechanical fastening and connection to electrical power prior to first use. The product can be connected to a supply network which meets energy quality standards as prescribed by law. To maintain the proper IP protection level, the right diameter of the power cable should be selected for the cable gland used in the product.

FUNCTIONAL CHARACTERISTICS

The product can only be used indoors.

USAGE GUIDELINES / MAINTENANCE

Any maintenance work must be performed when the power supply is cut off and the product has cooled down. Clean only with soft and dry cloths. Do not use chemical detergents. Do not cover the product. Ensure free air access. Product may heat up to a higher temperature. Product can only be supplied by rated voltage or voltage within the range provided. It’s forbidden to use the product with damaged protective cover. Product must not be used in unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air atmosphere, fumes, or chemical fumes, etc. Non-demountable product. Not suitable for independent repairs.

ENVIRONMENTAL PROTECTION

Keep your environment clean. Segregation of post-packaging waste is recommended. This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/neutralising. Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local authorities or sellers of such goods. Used items can also be returned to the seller when new product is purchased, in quantity no larger than the purchased item of the same type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in a given area is recommended.

COMMENTS / GUIDELINES

Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. For more information about Hoftronic products visit www.hoftronic.com. Hoftronic shall not be responsible for any damage resulting from the failure to follow these instructions. Hoftronic reserves the right to make changes in the manual – the current version can be downloaded at www.hoftronic.com.

DECLARATION OF CONFORMITY

DOCUMENTATION
This product has been manufactured and supplied in compliance with all relevant regulations and directives applicable to all member states of the European Union. The product complies with all applicable regulations and rules in the country of sale.
Formal documentation such as the declaration of conformity, the safety data sheet and the product test report is available upon request.

CE DECLARATION
The product complies with the following
directives:
LVD: 2014/35/EU
EMC: 2014/30/EU
RoHS: 2011/65/EU
The complete Declaration of Conformity Document (DOC) is available upon request.

Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands Made in P.R.C.
www.hoftronic.com

References

• HOFTRONIC - HOFTRONIC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>