SW02 Series Wifi and Bluetooth Smart Wall Switch User Manual
- June 28, 2024
- WiFi
Table of Contents
SW02 Series Wifi and Bluetooth Smart Wall Switch
Specifications:
- Working voltage: AC100–240V, 50/60HZ
- Rated load: Less than 1100W
- Wireless Type: Wi-Fi 2.4GHz (NOTE: not support 5GHz)
- Input voltage: AC100–240V, 50/60HZ
- Power consumption: 0.5W
- Working temperature: 0~40
- Wifi indicator: blue
- Switch status indicator: green
Product Usage Instructions:
Installation Steps:
-
Neutral wire (Required): Ensure you have a neutral wire before
installation. -
Ground wire (Optional): Suggested to connect if available.
-
Line/Load wire (Required): Connect the Load/Line wires
correctly as they are not interchangeable.
If unsure about which wire is which, try one configuration and
verify all connections are correct with wire nuts screwed
tightly.
How to Determine Neutral Wire:
A neutral wire allows the switch to be powered while keeping the
lighting circuit connected to your lights powered off. You likely
have neutrals if your house was built in the mid-1980s or
later.
Checking for Neutral Wires:
Turn off the breaker box, remove the trim plate over the switch,
take out the existing switch, and look at the wires. A white wire
indicates a neutral. To confirm, check the voltage between the
white and hot wires in the box.
Downloading the App:
To download the app, scan the QR code provided or search for
“Smart life” or “Tuya Smart” in the IOS App Store or Google Play.
Supported smartphone systems include Android 4.4 and above, and IOS
8.0 and above.
App Registration Steps:
-
Register or log in to the Smart life app using your cellphone
number or email address. -
Enter verification code received, set password, and complete
registration.
FAQ:
What is a neutral wire?
A neutral wire allows our switch to be powered while
simultaneously allowing the lighting circuit connected to your
lights to be power off.
Do I have neutral wires?
If your house was built in the mid-1980s or later, there is an
excellent chance that you have neutrals everywhere in your home.
Check near switch boxes for outlets or white wires to identify
neutrals.
Wifi&Blutooth Smart Wall Switch User Manual V1.0
Note: When pairing, the red light will flash. When the pairing is successful,
the red light will be off. The switch status indicates the green light can be
set according to the “light Modethe” can be 3 kinds of indication status
SW02 Series
Technical Parameters
Working voltage: AC100–240V, 50/60HZ Rated load: Less than 1100W Wireless
Type: Wi-Fi 2.4GHz (NOTE: not support 5GHz) Input voltage: AC100–240V, 50/60HZ
Power consumption: 0.5W Working temperature: 0~40 Wifi indicator blue, switch
status indicator green. Installation steps 1) Neutral wire(Required), but not
always present. You should to get
it before Installation. 2) Ground wire(Optional) suggest to connect up. 3)
Line/Load wire(Required). Connect the Load/Line wires correctly. They are
not interchangeable. If you can’t ensure which wires is line and which is
load, simply try one configuration. Note: verify all the connections are
correctly and wire nuts are screwed tightly.
What is a neutral wire?
A neutral wire allows our switch to be powered while simultaneously allowing the lighting circuit connected to your lights to be power off.
Do I have neutral wires?
If your house was built in the mid-1980s or later, there is an excellent chance that you have
neutrals everywhere in your home.
If there is an outlet (wall receptacle) near the switch, most likely that switch box has a
neutral.
Switches that are ganged together have a much higher likelihood of having neutrals, no
matter what year.
Checking the switch box
The best way is to check the actual wires in the switch box where you want to install .
Please observe all safety precautions before handling the electrical wiring in your switch
boxes.
Turn off your breaker box.
Take off the trim plate over the switch.
Remove the screws from your switch and pull out the existing switch to look at the wires.
If you see a white wire (or group of them), it is VERY likely that you have a neutral.
The only way to be absolutely sure that you have found a neutral wire is to check the voltage (110V/120V) between the white wire and the “hot” (usually black in color) wire in the box. In a standard switch/dimmer, the “hot” is using one of the two wires connected to the switch.
Ground Neutral Line Load1 Load2 Load3
How to download App? Scan the QR code below or search “Smart life” / “Tuya
Smart” in IOS APP store or Google play to download. Supported smart phone
system: Android 4.4 above IOS 8.0 above
Step 1: Registration and login “Smart life” APP. If you don’t have the account
of “Smart life” APP, register an account or sign in with cellphone number +
verification code. This page describes the Registration process. Describes: 1.
Tap “Register” in the upper right (Step 1). 2. The system automatically
determines your country /area. You can also select your country code by
yourself. Enter the cellphone number or E-mail address and then tap
“Next”(Step 2).
Step1
Step2
3. If you enter mobile cellphone number, you will get verification code in
few seconds, then enter the verification code in the message (Step 3), enter
password, tap”Done”to finish your registration. 4. If you enter E-mail
address, you will get verification code in your
E-mail in few seconds, and then enter the verification code in your
E-mail,enter password (Step 4), tap “Done “to finish your registration
Step3
2
Step4
How to connect to the Internet This smart switch has a variety of paring
network modes, mainly talking about fast and default paring network modes.
A:Fast paring network mode A-1. Turn on the phone Bluetooth
A-2. Make sure the red light of the smart switch flashes quickly. (If it does
not flash quickly, please press and hold any button for more than 5 seconds
until the red light flashes quickly.),At this time, the factory settings will
be temporarily restored, if the red light blinking stage is not connected to
the new network, in order to prevent accidental deletion, the smart switch
will be connected to the last successful pairing network
A-3. Open the “Smart life” APP and click on the “+” in the upper right corner A-4. The Bluetooth of the mobile phone and the smart switch will automatically communicate, the APP will pop up the device that can be configured with the network, click “go to add”
A-5.After clicking “+” again, enter the network name and password (but not Smart life’s) to be connected to, and click “confirm” to proceed to the next step A-6. Modify the name of the smart switch to facilitate identification, click “Done”. At this point, the smart switch is connected to the Internet, and you can use a third-party APP to control it.
A-7,For more personalized settings of the smart switch, please enter and click ” ” in the lower right corner
A-8,Multiple switches control one light function
Click the ” ” icon in the upper right corner, select “Multi-Control
Association”, select the switch that needs to be associated,”
B:default paring network modes B-1: Make sure the red light of the smart
switch flashes quickly. (If it does not flash quickly, please press and hold
any button for more than 5 seconds until
the red light flashes quickly.),then the switch enter the factory reset mode
and
also paring network modes. B-2: Make sure your mobile phone is connected to
WiFi(Just support 2.4GHz but not 5GHz) in your home. Click “+” in the upper
right corner of the
homepage. Then select “Switch(WiFi)”.
B-3: Enter your WiFi password (but not Smart life’s) and then click “Next”,
APP will enter searching device mode. Note: Make sure your phone and device
are as close to your router as possible.
B-4: Device added successfully, then rename the device name and choose the device location. Tap ‘Done’ enter the device page. Long press the switch 1, switch 2, switch 3 on the APP, then you can modify the name, you can modify the name according to your preferences, easy to operate,Convenient Alexa and Google assistant voice control. B-5.For more settings, see A-7&A-8
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: -Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. -Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help. *RF warning for Mobile device: This equipment complies
with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>