WiFi WCC941M Wi-Fi BT Transceiver User Manual
- June 12, 2024
- WiFi
Table of Contents
WCC941M Wi-Fi BT Transceiver
User Manual
Introduction
WCC941M is a highly integrated single chip which features a low power 2×2
11a/b/g/n/ac/ax Tri band Wi-Fi subsystem and a Bluetooth v5.2 subsystem,
offering feature-rich wireless connectivity at high standards, and delivering
reliable, cost-effective throughput from an extended distance.
The core chipset is from MediaTek part number MT7921AUN.
Product Details
-
Data Modulation
DSSS:CCK,BPSK,QPSK for 802.11b
OFDM:BPSK,QPSK,16QAM,64QAM,256QAM for 802.11a,g,n,ac,ax
FHSS:GFSK,OQPSK, 8DPSK, π/4DPSK for Bluetooth -
Frequency Range
2.4GHz： 2.4-2.4835GHz bands
5GHz ： 5.15-5.25GHz, 5.25-5.35GHz, 5.47-5.725GHz, 5.725-5.85GHz bands
6GHz ： 5.925-7.125GHz bands -
Output Power tolerance
Output power ± 2.0dBm -
Recommended Operating conditions
****| Min| Typ.| Max| Unit
---|---|---|---|---
Operating voltage| 4.5| 5 5| 5.5| V
Operating temperature(ambient)| -20| 25| 50| °C
Approval Statement
FCC approval
RF Software restrictions
-
Contention-Based Protocol, as demonstrated in the FCC test report, is permanently embedded in the module and is not host-dependent, can’t change by anyone.
-
Operation of transmitters in the 5.25-5.35GHz, 5.47-5.725GHz, 5.85-5.895GHz, 5.925-7.125GHz bands is this Modular device will only associate and connect with a low-power indoor access point or subordinate device and never directly connect to other client devices.
This feature is include in its firmware and can’t change by anyone. -
Operation of transmitters in the 5.25-5.35GHz, 5.47-5.725GHz, 5.85-5.895GHz, 5.925-7.125GHz bands is this Modular device will always initiate transmission under the control of a low-power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if the client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request.
-
That transmissions will be lower or equal to the power advertised by the indoor low-power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD.
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesirable operation.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter module FCC ID: A3LWCC941M
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
- The OEM integrator is responsible for ensuring the end-user has no manual instruction to remove or install module.
- The module is limited to installation in mobile or fixed applications.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
FCC regulations restrict operation of this device to indoor use only. The
operation of this device is prohibited on oil platforms, cars, trains, boats,
and aircraft, except that operation of this device is permitted in large
aircraft while flying above 10,000 feet.
Operation of transmitters in the 5.925-7.125 GHz band is prohibited for
control of or communications with unmanned aircraft systems.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03
OEM Manual v01 guidance, the following conditions must be strictly followed
when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15 Subpart C (15.247)
and Subpart E (15.407).
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any
other usage conditions such as colocation with other transmitter(s) will need
a separate reassessment through a class II permissive change application or
new certification.
This module is authorized for Low Power Indoor Client applications only; final
host product must be for indoor operations only.
Further operation restrictions on the host product include:
*Prohibited for control of or Communications with unmanned aircraft systems.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body.
A separate SAR/Power Density evaluation is required to confirm compliance with
relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas
of the same type with equal or lower gain may also be used with this module
except for operations within the 5.925~7.125GHz band.
Use of other antenna types or the same type of antenna with higher gain than
listed above must performed additional testing and appropriate permissive
change approval.
Note2 : In the 5.925-7.125GHz band, use of other similar type antennas
and the antenna gain not higher/lower than listed above may only require a
C1PC without any additional testing/submission.
Note3 : Additional testing/submission (C2PC) will required if device not
met the antenna and RF exposure requirements.
Note4 : Contact Samsung for additional guidance, if choose to use
different antenna types or higher/lower gain antennas in the end system.
IMPORTANT : The final host product must have an integral antenna which is
not removable by the end-user.
Antenna
Specification| Antenna type : Metal Antenna
Bluetooth/BLE : 0.79 dBi (BT0), 1.09 dBi (BT1)
WLAN 2.4GHz : 1.85 dBi (ANT L), 0.01 dBi (ANT R)
WLAN 5GHz : UNII 1, UNII 2A : 1.36 dBi (ANT L), 1.95 dBi (ANT R)
UNII 2C, UNII 3 : 1.49 dBi (ANT L), 1.98 dBi (ANT R)
WLAN 6GHz : 0.84 dBi (ANT L), 0.95 dBi (ANT R)
---|---
IMPORTANT : The final host product must have an integral antenna which is
not removable by the end-user.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: A3LWCC941M”. The grantee’s FCC ID can be used only when all
FCC compliance requirements are met.
2.9 Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and
any co-located or simultaneous transmission with other transmitter(s) class II
permissive change re-evaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does
not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement
applicable to the final host. The final host will still need to be reassessed
for compliance to this portion of rule requirements if applicable. As long as
all conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module
installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for reevaluating the end product (including the
transmitter) and obtaining a separate
FCC authorization. Manual Information
To the End User The OEM integrator has to be aware not to provide information
to the end user regarding how to install or remove this RF module in the
user’s manual of the end product which integrates this module. The end user
manual shall include all required regulatory information/warning as show in
this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the FCC rule such as FCC Part 15 Subpart B before it
can be placed on the US market. This includes reassessing the transmitter
module for compliance with the Radio and EMF essential requirements of the FCC
rules. This module must not be incorporated into any other device or system
without retesting for compliance as multi-radio and combined equipment.
Modules : extended to host manufacturers by integration instructions.
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an
uncontrolled environment. This device should be installed and must not be co-
located or operating in conjunction with any other antenna or transmitter.
This device is intended only for OEM integrators under the following
conditions:
- This module may not be co-located with any other transmitters or antennas.
- The antenna must be installed such that 20cm is maintained between the antenna and users.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements with this module
installed.
In the event that these conditions cannot be met, then the FCC & IC
authorizations are no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product including this module and
obtaining separate FCC & IC authorizations.
Contact info for above certified FCC:
Company Name: Samsung Electronics America, Inc
Contact Name: JENNI CHUN
Address: 19 Chapin Rd, Building D. Pine Brook, NJ 07058
Telephone No: 973-808-6375
Email : j1.chun@samsung.com
IC approval
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The host device must be labeled to display the Industry Canada certification
number of the module.
Contains transmitter module IC:649E-WCC941M
User Information
Caution : Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment.
-This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. (Canada)
-User should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
CE approval
-This device is restricted to indoor use only within the 5.15 ~ 5.35GHz Band and 5.945~6.425GHz Band. (Europe)
Frequency Range and Maximum Output Power (EIRP)
2400 MHz to 2483.5 MHz : Below 20 dBm for Bluetooth
2400 MHz to 2483.5 MHz : Below 20 dBm for 02.11b,g,n,ax
5150MHz to 5250 MHz : Below 23 dBm for 802.11a,n,ac,ax
5350MHz to 5725 MHz : Below 20 dBm for 802.11a,n,ac,ax
5725MHz to 5875 MHz : Below 14 dBm for 802.11a,n,ac,ax
5945MHz to 6425 MHz : Below 23dBm for 802.11 ax
AT BE BG CH CY CZ DE DK
EE ES EL Fl FR HR HU IE IS
IT LI LT LU LV MT NL NO PL
PT RO SE SI SK TR UK(NI)
Version 1.0
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>