EDIFIER EDF100080 Tabletop Wireless Speaker User Guide

Table of Contents

Specifications

Bluetooth Connection

To pair a Bluetooth device, select “EDIFIER D32” from the list of available Bluetooth devices on your device.
If the speaker is in hidden mode, press the button to exit this mode and allow new connections.
This speaker supports simultaneous connections with two Bluetooth devices. To connect a second device, follow the steps provided in the manual.

AirPlay Setup

How do I reset the speaker?

To reset the speaker, press and hold the reset button for 10 seconds until you see the indicator lights flash.

Can I use the speaker while charging?

Yes, you can use the speaker while it is charging. However, it is recommended to fully charge the speaker before extended use.

How do I update the firmware of the speaker?

Visit the Edifier website and navigate to the support section to find firmware update instructions for your specific model.

Note:

Images are for illustrative purposes only and may differ from the actual product.
The bundled USB connecting cable is for audio streaming only. Do not use it for device charging.
For the need for technical improvement and system upgrade, the information and specifications contained herein may be slightly different from the actual product. If any difference is found, the actual product prevails

Note:

Power input: 100-240V~ 50/60Hz 0.5A
This plug type is meant for illustration purposes only.
The indicator light is solid red when charging and turns off when the battery is full.
You can play music on the speaker while charging.
Note: When powered by the built-in battery, the speaker will automatically power off if there is no audio playback or operation for 30 minutes.
Note: The pin code for connection is “0000” if needed.
To enjoy all the Bluetooth functions of this product, make sure that your audio source device supports A2DP and AVRCP profiles.
If no device is connected in 30 minutes, the speaker will switch to Bluetooth hidden mode.
In this mode, (1) new devices cannot find the speaker, but (2) for a device that exists in the pairing record of this speaker, you can select “EDIFIER D32” from its Bluetooth device list to reconnect.
To exit from Bluetooth hidden mode, press the button.
To disconnect from the current Bluetooth device, press and hold the button for 1.5 seconds.
This speaker supports the simultaneous connection of two Bluetooth devices.

As illustrated, connect the first Bluetooth device to the speaker.
Press and hold the button on the speaker for 1.5 seconds.
On the second Bluetooth device, select “EDIFIER D32” in its Bluetooth device list to connect.
On the first Bluetooth device, select “EDIFIER D32” in its Bluetooth device list to reconnect.
- Pause or stop playback on the current Bluetooth device before streaming audio from the second one.

Note: The following operating systems support USB audio streaming: Windows 11, Windows 10, Windows 8, and Windows 7.
Note: In AUX and USB modes, volume sync is not supported. To adjust the volume, adjust the speaker and your device separately.

Note:

Make sure that your device is connected to your Wi-Fi network before connecting the speaker.
You can also use the Apple Home app or the EDIFIER ConneX app to complete the connection.

The following devices are supported:

To connect to another Wi-Fi network, press and hold the button on the speaker for 1.5 seconds, and then follow the instructions to complete the connection.
To learn more about EDIFIER, please visit www.edifier.com
For EDIFIER warranty queries, please visit the relevant country page on www.edifier.com and review the section titled Warranty Terms.
USA and Canada: service@edifier.ca
South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for local contact information

Declaration for EU

Frequency Band (Bluetooth): 2.402GHz ~ 2.480GHz
Frequency Band (Wi-Fi): 2.400GHz ~ 2.4835GHz, 5.15GHz ~ 5.35GHz, 5.47GHz ~ 5.725GHz, 5.725GHz ~ 5.85GHz
RF Power output: ≤20 dBm (EIRP) (5.725GHz~5.850GHz excluded)
RF Power output: ≤14 dBm (EIRP) (5.725GHz~5.850GHz)

This device may be restricted for use, depending on the local network.

Restrictions in the 5GHz band:

According to 10(10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE), Bulgaria (BG), Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), Norway (NO), the United Kingdom in respect of Northern Ireland (UK(NI)) , Iceland (IS), Liechtenstein (LI), Switzerland (CH) and Turkey (TR).
The WLAN function for this device is restricted to indoor use due to its operation in the 5.15 to 5.35 GHz frequency range
This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
For more information, please visit our website: www.edifier.com

EDIFIER ConneX app

NOTICE:

For the need for technical improvement and system upgrade, information contained herein may be subject to change from time to time without prior notice.
Products of EDIFIER will be customized for different applications. Pictures and illustrations shown in this manual may be slightly different from the actual product. If any difference is found, the actual product prevails.