V8 Pikes Peak Twin Turbo Monster Installation Guide

June 27, 2024
PEAK

V8 Pikes Peak Twin Turbo Monster

“`html

Product Specifications

  • Manufacturer: Peak Products Corporation
  • Fasteners Supplied:
    • 12 mm Pan head self-drilling screw
    • 19 mm Pan head self-drilling screw
    • 19 mm Flat head screw
    • 25 mm Flat head screw
    • 38 mm Pan head screw
    • 50 mm Coach screw with washer
    • 80 mm Coach screw with washer
    • 45 mm Connector bolt and nut
    • 35 mm Hinge bolt assembly

Product Usage Instructions

Anchoring Fasteners for Australia

Deck Structure – POST BASE Typical Anchoring Fasteners

Fasteners Required: Minimum End and Edge Distance

  • JD3 Timber e.g. Seasoned, Mixed Australia Hardwood
  • 100 mm End of Joist: 50 mm Edge of Joist: 40 mm

Deck Structure – BASE RAIL SUPPORT Typical Anchoring

Fasteners

Fasteners Required: Minimum End and Edge Distance

  • JD3, J3, JD4, J4 Timber e.g. Seasoned/Unseasoned Mixed
    Australian Hardwood, Mixed Softwood, Pine, Radiata, Australia

  • 2 x 10g x 38 mm Screw (provided with product)

  • 34 mm End of Stud: 49 mm Edge of Stud: 25 mm

Deck Structure – WALL BRACKET Typical Anchoring Fasteners

Fasteners Required: Minimum End and Edge Distance

  • JD3, J3, JD4, J4 Timber e.g. Seasoned/Unseasoned Mixed
    Australian Hardwood, Mixed Softwood, Pine, Radiata, Australia

  • 60 mm Concrete, Minimum strength 25 MPa

  • 4 x RamsetTM WERCS AnkascrewTM or RamsetTM AnkascrewTM, M6 x 50
    mm

  • 39 mm Minimum End and Edge Distance: End of Stud: 48 mm Edge of
    Stud: 24 mm

Anchoring Fasteners for New Zealand

Deck Structure – POST BASE Typical Anchoring Fasteners

Fasteners Required: Minimum End and Edge Distance

  • J1 Timber – 60 mm End of Joist: 50 mm Edge of Joist: 40 mm

  • J2 Timber – 75 mm End of Joist: 50 mm Edge of Joist: 40 mm

  • J3 Timber – 100 mm End of Joist: 50 mm Edge of Joist: 40
    mm

  • J4 Timber e.g. Unseasoned, Pine, Radiata, Australia – 145 mm
    End of Joist: 50 mm Edge of Joist: 40 mm

  • J5 Timber e.g. Radiata Pine, Rimu, Douglas Fir, Larch – 215 mm
    End of Joist: 50 mm Edge of Joist: 40 mm

  • Concrete, Minimum strength 25 MPa – 4 x RamsetTM WERCS
    AnkascrewTM or RamsetTM AnkascrewTM, M10 x 100 mm

Frequently Asked Questions (FAQ)

Q: What should I do if I encounter issues during

installation?

A: If you encounter any issues during installation, please
contact our customer support for assistance.

Q: Is there a warranty for this product?

A: Peak Products Corporation does not provide a warranty for
improper installation or use of the product. Please refer to the
Australian Consumer Law in Australia or the Consumer Guarantees Act
in New Zealand for further information.

“`

Installation Guide

Tools and Materials Needed

· Mitre saw (recommended) or hacksaw with non-ferrous metal cutting blade
· Spirit level · Measuring tape · Drill · Drill bits for timber: 10 mm · Drill bits for metal: 3 mm, 5.5 mm

· Philips #1, #2, #3 driver bits · Socket or nutsetter:
8 mm, 17 mm · Adjustable spanner · Clamps · Painter’s masking tape · Dish soap (for glass panels)

· Non-corrosive exterior silicone caulking
· Anchoring fasteners (see pages 3-4)

Fasteners Supplied

12 mm Pan head self-drilling screw
19 mm Pan head self-drilling screw
19 mm Flat head screw
25 mm Flat head screw
38 mm Pan head screw

50 mm Coach screw with washer
80 mm Coach screw with washer
45 mm Connector bolt and nut
35 mm Hinge bolt assembly

See our helpful installation videos on our website: peakbalustrade.com.au · peakbalustrade.com.nz

Dear Customer,
We’d like to take a moment to say “thank you and congratulations” for choosing our products. At Peak® your satisfaction is very important to us. That is why we work very hard to provide you with products of exceptional quality, value, and beauty. And that is also why we want to hear from you.
Please contact us with your comments or suggestions at: support@peakproducts.com.au · support@peakproducts.co.nz
Finally, we’d like to remind you to always work safely. Then, take pride, relax with your family and experience years of enjoyment with Peak® products.
Peak Products Corporation

IMPORTANT INFORMATION

· Before beginning work, read this installation guide in its entirety including all warnings and important information.

· This installation guide is updated occasionally. Please refer to the latest version at https://peakproducts.com/en-au/peak-aluminium-balustrade /installation-videos-guides/ https://peakproducts.com/en-nz/peak-aluminium- balustrade/installation-videos-guide/

· Maximum post spacing: decks: 1.80 m stairs: 1.75 m

· For commercial use including multi-residential housing, please contact Peak Customer Service at:
Australia: 1300 734 714 · support@peakproducts.com.au New Zealand: 0800 800 040 · support@peakproducts.co.nz

· Complies with: Australian/New Zealand Standard AS/NZS 1170.0:2002 Structural design actions Conditions apply. For details visit: https://peakproducts.com/en-au/peak-aluminium-balustrade/compliance/ https://peakproducts.com/en-nz/peak-aluminium-balustrade/compliance/ Complete Peak® Aluminium Balustrade system required.
· Always understand and comply with your local building codes.

· To prevent timber splitting and rot, drill pilot holes and coat fastener screw threads with non-corrosive exterior silicone caulking.

· Ensure that the opening between each of the following is less than 100 mm:

– balusters

– glass panels

– balusters and posts

– glass panels and posts

– balusters and walls

– glass panels and walls

– balusters and glass panels – base rail and deck surface

WARNING No representation or warranty is given that your particular application of these products
complies with relevant building codes or that the fasteners provided or used are appropriate for your application. Consult with professionals and local building officials before beginning work: (i) to ensure compliance with relevant building codes for your application and for your proposed use of fasteners; (ii) to ensure the integrity of the structural components in connection with which these products are to be used; (iii) to identify appropriate safety gear that is to be used during installation such as a safety harness when working above ground; (iv) to ensure that the work area is free from utilities, services and hazards; and (v) to clarify any instructions or warnings that may not be clear. Work in a safe manner wearing protective gear such as gloves, eyewear, headwear, footwear and clothing. When using tools comply with operation manuals and instructions. Metal and glass may have sharp edges and could fragment or splinter during or as a result of handling or cutting. Do not use these products in connection with any substance that is or may be harmful or corrosive to the products. Inspect and maintain these products and the structural components that they are used in connection with on a regular basis, using professionals when appropriate.
Peak Products Corporation shall not be liable for any loss or damage resulting from the improper installation or improper use of this product, subject to any contrary provision of the Australian Consumer Law in Australia or the Consumer Guarantees Act in New Zealand. Peak products and associated materials are protected by patents, designs, copyrights and/or trademarks used under license from Peak Innovations Inc.
II01PB_InstallGuide_V8
2

ANCHORING FASTENERS FOR AUSTRALIA
WARNING Engineering design has determined appropriate fasteners for the attachment of the post base, wall bracket, and base rail support to concrete or timber structures designed by others. While the types of material are defined in the table below, the ability of the supporting structure to provide adequate support to Peak® Aluminium Balustrade system and its fasteners must be independently verified for each installation. To meet certain balustrade load requirements within AS/NZS 1170.1:2002, use the fasteners specified in the tables below. Building codes may vary. Always understand and comply with your local building codes.
For further information visit: https://peakproducts.com/en-au/peak-aluminium- balustrade/compliance/

Deck Structure

POST BASE Typical Anchoring Fasteners

Fasteners Required

Minimum Embedment¹

Minimum End and Edge Distance

JD3 Timber e.g. Seasoned, Mixed Australia Hardwood

4 x M10 Coach Screw²

100 mm

End of Joist: 50 mm Edge of Joist: 40 mm

J3 Timber e.g. Unseasoned, Mixed Australian Hardwood
JD4 Timber e.g. Seasoned, Mixed Softwood Species
J4 Timber e.g. Unseasoned, Pine, Radiata, Australia
Concrete, Minimum strength 25 MPa

4 x M10 Coach Screw²
4 x M10 Coach Screw²
4 x M10 Coach Screw² 4 x RamsetTM WERCS AnkascrewTM or RamsetTM AnkascrewTM, M10 x 100 mm

125 mm 145 mm 185 mm 72 mm

End of Joist: 50 mm Edge of Joist: 40 mm
End of Joist: 50 mm Edge of Joist: 40 mm
End of Joist: 50 mm Edge of Joist: 40 mm
70 mm

BASE RAIL SUPPORT Typical Anchoring Fasteners

Deck Structure

Fasteners Required

Minimum Embedment¹

Minimum End and Edge Distance

JD3, J3, JD4, J4 Timber e.g. Seasoned/Unseasoned Mixed Australian Hardwood, Mixed Softwood, Pine, Radiata, Australia

2 x 10g x 38 mm Screw (provided with product)

34 mm

End of Stud: 49 mm Edge of Stud: 25 mm

Concrete, Minimum strength 25 MPa

2 x RamsetTM AnkascrewTM M5 x 30 mm

27 mm

40 mm

WALL BRACKET Typical Anchoring Fasteners

Deck Structure

Fasteners Required

Minimum Embedment¹

JD3, J3, JD4, J4 Timber e.g. Seasoned/Unseasoned Mixed Australian Hardwood, Mixed Softwood, Pine, Radiata, Australia

4 x 14g Type 17 Screw³ or 4 x M6 Coach Screw² (provided with product)

60 mm

Concrete, Minimum strength 25 MPa

4 x RamsetTM WERCS AnkascrewTM or RamsetTM AnkascrewTM, M6 x 50 mm

39 mm

Minimum End and Edge Distance
End of Stud: 48 mm Edge of Stud: 24 mm
50 mm

¹ Depth of the threaded portion of the screw into the innermost member. ² Material of steel coach screws shall be given in AS/NZS 4291.1, for property classes 4.6 and 4.8. ³ Material of 14g Type 17 screws shall be given in AS 3566.
3

ANCHORING FASTENERS FOR NEW ZEALAND
WARNING Engineering design has determined appropriate fasteners for the attachment of the post base, wall bracket, and base rail support to concrete or timber structures designed by others. While the types of material are defined in the table below, the ability of the supporting structure to provide adequate support to Peak® Aluminium Balustrade system and its fasteners must be independently verified for each installation. To meet certain balustrade load requirements within AS/NZS 1170.1:2002, use the fasteners specified in the tables below. Building codes may vary. Always understand and comply with your local building codes. For further information and more anchoring recommendations, visit: https://peakproducts.com/en-nz/peak-aluminium- balustrade/compliance/

POST BASE Typical Anchoring Fasteners

Deck Structure

Fasteners Required

Minimum

Minimum End and

Embedment¹

Edge Distance

J1 Timber

4 x M10 Coach Screw²

60 mm

End of Joist: 50 mm Edge of Joist: 40 mm

J2 Timber

4 x M10 Coach Screw²

75 mm

End of Joist: 50 mm Edge of Joist: 40 mm

J3 Timber

4 x M10 Coach Screw²

100 mm

End of Joist: 50 mm Edge of Joist: 40 mm

J4 Timber e.g. Unseasoned, Pine, Radiata, Australia

4 x M10 Coach Screw²

145 mm

End of Joist: 50 mm Edge of Joist: 40 mm

J5 Timber e.g. Radiata Pine, Rimu, Douglas Fir, Larch

4 x M10 Coach Screw²

215 mm

End of Joist: 50 mm Edge of Joist: 40 mm

Concrete, Minimum strength 25 MPa

4 x RamsetTM WERCS AnkascrewTM or RamsetTM AnkascrewTM, M10 x 100 mm

72 mm

70 mm

BASE RAIL SUPPORT Typical Anchoring Fasteners

Deck Structure

Fasteners Required

Minimum Embedment¹

Minimum End and Edge Distance

J1, J2, J3, J4, J5 Timber e.g. Seasoned/ Unseasoned, Pine, Radiata, Australia,
Rimu, Douglas Fir, Larch

2 x 10g x 38 mm Screw (provided with product)

34 mm

End of Stud: 49 mm Edge of Stud: 25 mm

Concrete, Minimum strength 25 MPa

2 x RamsetTM AnkascrewTM M5 x 30 mm

27 mm

40 mm

WALL BRACKET Typical Anchoring Fasteners

Deck Structure

Fasteners Required

Minimum Minimum End and

Embedment¹

Edge Distance

J1, J2, J3, J4, J5 Timber e.g. Seasoned/ Unseasoned, Pine, Radiata, Australia,
Rimu, Douglas Fir, Larch

4 x 14g Type 17 Screw³ or 4 x M6 Coach Screw² (provided with product)

40 mm

End of Stud: 60 mm Edge of Stud: 30 mm

Concrete, Minimum strength 25 MPa

4 x RamsetTM WERCS AnkascrewTM or RamsetTM AnkascrewTM, M6 x 50 mm

39 mm

50 mm

¹ Depth of the threaded portion of the screw into the innermost member. ² Material of steel coach screws shall be given in AS/NZS 4291.1, for property classes 4.6 and 4.8. ³ Material of 14g Type 17 screws shall be given in AS 3566.
4

WALL BRACKET INSTALLATION
This symbol indicates important information.

1

Measure and mark the position of all brackets on the wall.

Maximum wall bracket spacing of 1.80 m.

1005 mm

2

For timber attachment, secure hand and base rail brackets to wall using four M6 coach

screws with washers.

To prevent timber rot, coat fastener screw threads with non-corrosive exterior silicone caulking.

For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.

60 mm

3 Follow the Baluster, Glass Panel, or Sectional Glass installation process as shown on pages 6-11.
HORIZONTAL ANGLE BRACKET INSTALLATION
This symbol indicates important information.

1

Measure and mark the hole positions of all brackets on the post.

Maximum post spacing of 1.80 m.

938 mm 46 mm

2

A: Drill 5.5 mm pilot holes at the marked locations.

A

B

B: Attach the hand and base rail

brackets to the post using four

25 mm flat head screws.

Then assemble the base rail bracket

using the connector bolt.

3 Follow the Baluster, Glass Panel, or
Sectional Glass installation process as shown on pages 6-11.
5

BALUSTER INSTALLATION
This symbol indicates important information.
For wall bracket or horizontal angle bracket installation, please see page 5.
1 Measure and mark the position of all posts and space equally.
Maximum post spacing of 1.80 m. Put the first post in position. For timber attachment, secure post to deck using four M10 coach screws (refer to pages 3-4 for required length) through each corner of the post base. Ensure that the post is plumb.
To prevent splitting of deck boards, drill four 10 mm holes through deck boards (but not into deck structure). To prevent timber rot, coat fastener screw threads with non-corrosive exterior silicon caulking. For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.

2

Temporarily position the second post but do NOT secure it yet. Cut the hand and base rails and

plastic baluster gaskets to fit between the posts.

3

A: Install the base rail support into the bottom channel of the base rail.

A

To ensure that the balusters remain engaged in the rails, you must install one base rail support for each balustrade section.

B: Install all but the last four spacers into each rail.

A

4

Insert the rails (fitted with plastic baluster gaskets) into the first post. Then insert the

rails into the second post as a temporary

support but do not secure it yet.

A: Secure the handrail to the first post with

19 mm pan head self-drilling screws.

B: Secure the base rail to the first post with

19 mm pan head self-drilling screws.

B

C: Slide the first spacer in each rail against

the first post.

D: Insert a baluster into the base rail and

swing the top of the baluster into the

handrail. Repeat until you can no longer

swing balusters into position.

The opening between balusters, and

between a baluster and a post, must

C

not exceed 100 mm.

B D

6

5

A: Remove the second post to install the last few balusters and spacers.

B: Cut the last spacers flush with the ends

of the rails.

To ensure equal baluster spacing at each post, cut the first and the last spacers in the hand and base rails to equal lengths.

6

A: Insert the rails into the second post. B: Position and fasten the second post

in place, ensuring that the post is

plumb (see step 1 for full details).

B A
A B

7

A: Secure the handrail to the second post with 19 mm pan head self-

drilling screws.

B: Secure the base rail to the second

post with 19 mm pan head self-

drilling screws.

C: Slide the base rail support to the

centre position.

D: For timber attachment, fasten the

base rail support to the deck using

two 38 mm pan head screws.

For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.

To ensure that the balusters remain engaged in the rails, you must install one base rail support for each balustrade section.

C D

8 Repeat all steps for remaining sections.
Optional: Install post base covers.

A B
7

GLASS PANEL INSTALLATION
This symbol indicates important information.
Always use two people to handle glass panels. Always lift a glass panel by its sides. Toughened glass is extremely fragile ­ do not bump the edges. Always use protective gear including eyewear and gloves when handling glass panels.
For wall bracket or horizontal angle bracket installation, please see page 5.
1 Measure and mark the position of all posts and space equally.
Maximum glass width of 1025 mm and maximum post spacing: 1.80 m for sections with a glass panel and balusters. 1.20 m for sections with a glass panel only.
Put the first post in position. For timber attachment, secure post to deck using four M10 coach screws (refer to pages 3-4 for required length) through each corner of the post base. Ensure that the post is plumb.
To prevent splitting of deck boards, drill four 10 mm holes through deck boards (but not into deck structure). To prevent timber rot, coat fastener screw threads with non-corrosive exterior silicon caulking. For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.

A

B

2

A: Remove the plastic baluster gaskets from both rails.

B: Temporarily position the second

post but do NOT secure it yet.

Cut the hand and base rails to

fit between the posts.

3

A: Cut the glass gaskets the same length as the rails.

A

B

B: Drill 3 mm holes into the base rail

glass gasket (the smaller gasket)

every 300 mm for water drainage.

4 A: Press the glass gaskets into the rails.

The smaller of the two glass

A

B

gaskets goes into the base rail.

B: Install the base rail support into the bottom channel of the base rail.
To ensure that the glass panel remains engaged in the rails, you must install one base rail support for each balustrade section.

8

5

A: Insert the rails into the posts. B: Position and fasten the second post

A

in place, ensuring that the post is

B

plumb (see step 1 for full details).

C: Slide the base rail support to the

centre position.

D: For timber attachment, fasten the

base rail support to the deck using

two 38 mm pan head screws.

For concrete attachment, refer to pages 3-4 for anchoring fastener

C

recommendations.

To ensure the glass panel remains

engaged in the rails, you must

D

install one base rail support for

each balustrade section.

6

Secure the rails to both posts with 19 mm pan head self-drilling screws.

7 Install the glass panel by inserting it
into the handrail gasket then lowering it into the base rail gasket.
Ensure that the glass gaskets and the top and bottom edges of the glass panel are well lubricated with liquid soap before installing the glass panel. Ensure that the glass is fully seated in the gaskets. Wash away excess soap with clean water. The opening between a glass panel and a post must not exceed 100 mm. Maximum of one glass panel between posts.
8 Repeat all steps for remaining sections.
Optional: Install post base covers.
9

SECTIONAL GLASS KIT INSTALLATION
This symbol indicates important information. Always lift a glass panel by its sides. Toughened glass is extremely fragile ­ do not bump the edges. Always use protective gear including eyewear and gloves when handling glass panels. For wall bracket or horizontal angle bracket installation, please see page 5.

1 Measure and mark the position of all posts and space equally.
Maximum post spacing of 1.80 m.

Put the first post in position. For timber attachment, secure post to deck using four M10 coach screws (refer to pages 3-4 for required length) through each corner of the post base. Ensure that the post is plumb.
To prevent splitting of deck boards, drill four 10 mm holes through deck boards (but not into deck structure).
To prevent timber rot, coat fastener screw threads with non-corrosive exterior silicon caulking.
For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.
B

2

A: Remove the plastic baluster gaskets from both rails.

A

B: Temporarily position the second post

but do NOT secure it yet. Cut the hand

and base rails to fit between the posts.

This kit was designed to fit into a 1.80 m balustrade section. If your balustrade section is shorter than 1.80 m, you will need to cut the spacers or remove the glass panel(s) accordingly.

3

A: Install the base rail support into the bottom channel of the base rail.

A

B

To ensure that the glass panels remain engaged in the rails, you must install one base rail support for each balustrade section.

B: Install the first pair of spacers in the hand and base rails.

4

Insert the rails into the first post. Then insert the rails into the second post as a temporary

A

B

support but do not secure it yet.

A: Secure the handrail to the first post using

19 mm pan head self-drilling screws.

B: Secure the base rail to the first post with

19 mm pan head self-drilling screws.

C: Slide the first spacer in each rail against

the first post.

A

5

Remove the second post. A: Attach the glass fittings to the top and bottom

of each glass panel.

B: Slide a glass panel with fittings attached into the

rails until touching the first pair of spacers. Then

slide the second pair of spacers into the hand

and base rails. Repeat to complete the section.

The opening between glass panels, and between a glass panel and a post, must not exceed 100 mm.

C B

10

6

Cut the last spacers flush with the ends of the rails.

To ensure equal glass panel spacing at each post, cut the first and the last spacers in the hand and base rails to equal lengths.

7

A: Insert the rails into the second post. B: Position and fasten the second post in

place, ensuring that the post is plumb

(see step 1 for full details).

A B

8

A: Secure the handrail to the second post with 19 mm pan

head self-drilling screws.

B: Secure the base rail to the

second post with 19 mm pan

head self-drilling screws.

C: Slide the base rail support to

the centre position.

D: For timber attachment, fasten

the base rail support to the

deck using two 38 mm pan

head screws. C

For concrete attachment,

refer to pages 3-4 for

anchoring fastener recommendations.

D

To ensure that the glass panels remain engaged in the rails, you must install one base rail support for each balustrade section.

9 Repeat all steps for remaining sections.
Optional: Install post base covers.

A B
11

STAIR BALUSTER INSTALLATION
This symbol indicates important information.
1 Measure and mark the position of all posts and space equally.
Maximum post spacing of 1.75 m. Put the first post in position. For timber attachment, secure post to deck using four M10 coach screws (refer to pages 3-4 for required length) through each corner of the post base. Ensure that the post is plumb.
To prevent splitting of deck boards, drill four 10 mm holes through deck boards (but not into deck structure). To prevent timber rot, coat fastener screw threads with non-corrosive exterior silicon caulking. For concrete attachment, refer to pages 3-4 for anchoring fastener recommendations.

2 A: Remove the screw covers from

the rails.

B: Insert a baluster through the

A

B

first and last square slots at each

end of the base rail (ensure

the screw holes in the rails and

balusters are facing up). Align

the screw hole in each baluster

with the screw hole in the base

rail, then fasten each baluster to

the rail using 12 mm pan head

self-drilling screws.

3

Insert the balusters into each end of the handrail (ensure the screw holes in

the rail are facing up). Align the screw

hole in each baluster with the screw

hole in the handrail, then fasten each

baluster to the rail using 12 mm pan

head self-drilling screws.

4

A: Insert the next baluster through the square slot in the base rail.

A

B

B: Insert baluster into the handrail

and align the screw holes with

the screw holes in the rails. Fasten

baluster to the rails using 12 mm

pan head self-drilling screws.

Repeat to complete the panel.

5 A: Install the handrail screw cover.

A

B

B: Install the base rail screw cover.

Secure the screw covers to the rails with painter’s masking tape to prevent them from sliding during the remainder of the installation.

12

6

Put the balustrade panel and bottom post into position and clamp the posts and rails

together but do not secure the bottom post

yet. Ensure equal baluster spacing at each

post, and that the bottom post is plumb. To

allow space for the brackets, mark a vertical

line 10 mm away from each post and cut

the rails along the marked line.

Always understand and comply with your local building codes for stair rail height, size of openings under the base rail, between balusters, and between a baluster and a post.

10 mm

10 mm 10 mm

7

A: Reposition the balustrade panel in between the posts at the required

height above the noses of the treads.

Place and mark positions of each

base rail bracket. Then remove the

panel in order to mark hole positions

for each bracket on the posts.

B: Drill 5.5 mm pilot holes through

the post at the marked positions.

C: Fasten the base rail brackets to

the posts, using four 25 mm flat

head screws.

D: Position and fasten the bottom

post in place, ensuring that the

post is plumb (see step 1 for

full details).

A

B

D

C

8

A: Temporarily position the balustrade panel in the base

rail brackets and mark the

position of the bracket and

hole positions of each

handrail bracket on the posts.

B: Drill 5.5 mm pilot holes

through the post at the

marked positions.

C: Fasten the handrail

brackets to the posts,

using four 25 mm flat

head screws.

A

B

C

9

A: Reposition the balustrade panel, then drill 3 mm pilot holes through

A

B

C

the rails at the screw positions.

B: Attach the balustrade panel to the

brackets and secure with 19 mm

flat head screws.

C: Slide a screw cover over each

bracket.

10 Repeat all steps for remaining sections.
Optional: Install post base covers.

13

GATE INSTALLATION
B This symbol indicates important information.
Before beginning work, measure and ensure the Gate Opening (W) does not exceed 1150 mm. Then please carefully follow the steps below to ensure the gate is not cut too short for your project.

1

A: Remove latch side of gate frame.

A

B: With latch side of

gate frame removed,

cut top and bottom

gate rails 190 mm

shorter than gate

opening W.

W (1150 mm max.) W minus 190 mm

2

Attach the latch side of the gate frame using

the 19 mm pan head

self-drilling screws.

A

3

A: Align the top of the gate with the top of the post and mark the hole

positions for the hinges on the post.

B: Drill 5.5 mm pilot holes at the

marked positions.

C: Install the top 50 mm coach screw

on each hinge.

D: Install the bottom 50 mm coach

C

screw on each hinge by releasing

the bolt and nut (HINT: do not

completely disassemble hinge).

4

Use 19 mm pan head self drilling screws for these steps:

A

A: Secure the retainer to

the gate at the marked

position.

B: Insert the latch through

the retainer.

C: Secure the latch to the

gate at the marked

position.

B

D: Check and mark the

position for the latch

plate on the post.

Secure the latch plate to

the post.

14

B D
D C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PEAK User Manuals

Related Manuals