APX N50 2 Way Portable Radio

Product Information: APXTM Two-Way Radios

Specifications:

• Model: 2
• APX N50 User Guide
• AUGUST 2023

Chapter 1: Radio Care

1.1 Cleaning Your Radio

To ensure optimal performance and longevity of your APXTM
Two-Way Radio, it is important to keep it clean. Follow the steps
below to clean your radio:

1. Turn off the radio and remove the battery.

2. Use a soft, lint-free cloth or a slightly damp cloth to wipe
   the exterior surfaces of the radio.

3. Avoid using abrasive cleaners or solvents that may damage the
   radio.

4. Allow the radio to air dry before reassembling and using
   it.

1.2 Radio Service and Repair

If your APXTM Two-Way Radio requires service or repair, please
follow these guidelines:

• Contact our customer support for assistance in diagnosing the
  issue and determining the appropriate course of action.

• Do not attempt to disassemble or repair the radio yourself, as
  it may void the warranty and cause further damage.

• Follow the instructions provided by our customer support team
  for sending the radio for service or repair.

1.3 Battery Recycling and Disposal

Proper disposal of batteries is important for environmental
protection. Follow these guidelines for battery recycling and
disposal:

• Always remove the battery from the radio before recycling or
  disposing of it.

• Check local regulations and recycling facilities for proper
  disposal methods.

• Do not dispose of batteries in regular household waste.

Chapter 2: Radio Overview

2.1 Keypad Overview

The keypad on your APXTM Two-Way Radio allows you to access
various functions and settings. Familiarize yourself with the
keypad layout as shown in the user manual.

2.2 Programmable Radio Functions

Your APXTM Two-Way Radio has programmable functions that can be
customized according to your specific needs. Refer to the user
manual for instructions on programming these functions.

2.3 ViQi

ViQi is a voice control feature available on your APXTM Two-Way
Radio. It allows you to perform certain actions using voice
commands. Follow the instructions below to activate and use
ViQi:

2.3.1 Activating Basic Voice Control

1. Press and hold the designated ViQi button on the radio.

2. Wait for the audio prompt indicating that ViQi is
   activated.

3. Speak clearly and audibly into the microphone to give voice
   commands.

2.3.2 Using ViQi Virtual Partner

1. Activate ViQi as described in section 2.3.1.

2. Ask ViQi questions or give commands related to the Virtual
   Partner feature.

3. Follow the audio prompts and respond accordingly to interact
   with the Virtual Partner.

Chapter 3: Getting Started

3.1 Attaching and Removing the Battery

Follow these steps to attach or remove the battery from your
APXTM Two-Way Radio:

Attaching the Battery

1. Ensure the radio is turned off.

2. Align the battery contacts with the corresponding terminals
   inside the battery compartment.

3. Slide the battery into the compartment until it clicks into
   place.

Removing the Battery

1. Turn off the radio.

2. Press the battery release button, usually located on the bottom
   or side of the radio.

3. Slide the battery out of the compartment.

3.2 Attaching and Removing the Antenna

Follow these steps to attach or remove the antenna from your
APXTM Two-Way Radio:

Attaching the Antenna

1. Ensure the radio is turned off.

2. Align the antenna connector with the corresponding port on the
   top of the radio.

3. Gently push and twist the antenna clockwise until it is
   securely attached.

Removing the Antenna

1. Turn off the radio.

2. Gently twist the antenna counterclockwise to detach it from the
   radio.

3. Store the antenna in a safe place to avoid damage or loss.

FAQ (Frequently Asked Questions)

Q: How often should I clean my APXTM Two-Way Radio?

A: It is recommended to clean your radio regularly, especially
if it is exposed to dirt, dust, or moisture. A general guideline is
to clean it every few weeks or as needed.

Q: Can I program my own functions on the APXTM Two-Way

Radio?

A: Yes, the APXTM Two-Way Radio has programmable functions that
can be customized according to your needs. Please refer to the user
manual for instructions on programming these functions.

Q: Can I use ViQi in noisy environments?

A: ViQi is designed to work in various environments, including
noisy ones. However, it is recommended to speak clearly and
directly into the microphone for better voice recognition.

APXTM Two-Way Radios
Model 2
APX N50 User Guide

AUGUST 2023
© 2023 Motorola Solutions, Inc. All rights reserved

MN009203A01
MN009203A01-AD

MN009203A01-AD Contents
Contents
List of Figures………………………………………………………………………………………………..8 List of Tables………………………………………………………………………………………………… 9 Legal and Support………………………………………………………………………………………..10
Intellectual Property and Regulatory Notices…………………………………………………………………….10 Legal and Compliance Statements………………………………………………………………………………….11
Disclaimer…………………………………………………………………………………………………………. 11 Declaration of Conformity……………………………………………………………………………………. 11 Industry Canada WLAN Statement………………………………………………………………………..12 Important Safety Information…………………………………………………………………………………12 Notice to Users (FCC) …………………………………………………………………………………………13 FCC Licensing Information………………………………………………………………………………….. 13 Applying for Canadian License…………………………………………………………………………….. 14 Limited Warranty…………………………………………………………………………………………………………..14 MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS…………………………………… 14 I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:……………………………….. 14 II. GENERAL PROVISIONS:……………………………………………………………………………….. 15 III. STATE LAW RIGHTS:……………………………………………………………………………………. 15 IV. HOW TO GET WARRANTY SERVICE:……………………………………………………………. 15 V. WHAT THIS WARRANTY DOES NOT COVER:………………………………………………….16 VI. PATENT AND SOFTWARE PROVISIONS:………………………………………………………. 16 VII. GOVERNING LAW:……………………………………………………………………………………….17 VIII. For Australia Only…………………………………………………………………………………………17
Read Me First……………………………………………………………………………………………….18
Software Version…………………………………………………………………………………………………………. 18
Chapter 1: Radio Care……………………………………………………………………………….. 19
1.1 Cleaning Your Radio………………………………………………………………………………………………..19 1.2 Radio Service and Repair…………………………………………………………………………………………20 1.3 Battery Recycling and Disposal………………………………………………………………………………… 20
Chapter 2: Radio Overview………………………………………………………………………… 21
2.1 Keypad Overview…………………………………………………………………………………………………….22 2.2 Programmable Radio Functions……………………………………………………………………………….. 23 2.3 ViQi………………………………………………………………………………………………………………………. 26
2.3.1 Activating Basic Voice Control……………………………………………………………………… 28 2.3.2 Using ViQi Virtual Partner……………………………………………………………………………. 28
Chapter 3: Getting Started…………………………………………………………………………..29
2

MN009203A01-AD Contents
3.1 Attaching and Removing the Battery…………………………………………………………………………. 29 Attaching the Battery……………………………………………………………………………………………29 Removing the Battery…………………………………………………………………………………………. 29
3.2 Attaching and Removing the Antenna……………………………………………………………………….. 29 Attaching the Antenna………………………………………………………………………………………….29 Removing the Antenna……………………………………………………………………………………….. 29
3.3 Attaching and Removing the Accessory Connector Cover…………………………………………….30 Attaching the Accessory Connector Cover…………………………………………………………….. 30 Removing the Accessory Connector Cover……………………………………………………………. 30
3.4 Attaching the Belt Clip…………………………………………………………………………………………….. 30 3.5 Charging the Radio………………………………………………………………………………………………….30 3.6 Turning the Radio On or Off…………………………………………………………………………………….. 31
Turning the Radio On…………………………………………………………………………………………..31 Turning the Radio Off…………………………………………………………………………………………..31 3.7 Adjusting the Volume of the Radio……………………………………………………………………………. 31
Chapter 4: Home Screen Overview…………………………………………………………….. 32
4.1 Status Indicators…………………………………………………………………………………………………….. 32 4.1.1 Status Icons………………………………………………………………………………………………. 33 4.1.2 LED Indications…………………………………………………………………………………………..36 4.1.3 Intelligent Lighting Indicators……………………………………………………………………….. 37 4.1.4 Transmit and Receive Indicators………………………………………………………………….. 37
Chapter 5: General Radio Operation…………………………………………………………… 39
5.1 Selecting Zones……………………………………………………………………………………………………… 39 5.2 Selecting Channels………………………………………………………………………………………………….39
5.2.1 Channel Error Message………………………………………………………………………………. 39 5.3 Mode Select Feature………………………………………………………………………………………………. 39
5.3.1 Saving Zones and Channels…………………………………………………………………………40 5.4 Selecting the Power Level……………………………………………………………………………………….. 40 5.5 Selecting a Radio Profile…………………………………………………………………………………………. 40 5.6 Enabling and Disabling the Radio Alias………………………………………………………………………40 5.7 Adjusting the Display Backlight………………………………………………………………………………….41 5.8 Editing the Time and Date……………………………………………………………………………………….. 41 5.9 Locking and Unlocking the Controls………………………………………………………………………….. 41 5.10 Setting the Tones for Controls and Buttons ………………………………………………………………41 5.11 Setting the Voice Mute……………………………………………………………………………………………42 5.12 Using the Time-Out Timer……………………………………………………………………………………… 42 5.13 Adjusting the Squelch Level…………………………………………………………………………………… 42 5.14 Conventional Squelch Operation…………………………………………………………………………….. 43
5.14.1 Setting Conventional Squelch Operation……………………………………………………… 43
3

MN009203A01-AD Contents
5.15 Using the PL Disable Feature………………………………………………………………………………….44 5.16 Digital PTT ID Support …………………………………………………………………………………………..44 5.17 General Radio Information………………………………………………………………………………………44
5.17.1 Accessing the General Radio Information……………………………………………………. 44
Chapter 6: Trunking System Controls………………………………………………………….46
6.1 Operating in Failsoft System……………………………………………………………………………………..46 6.2 Imbalanced Coverage………………………………………………………………………………………………46 6.3 Out-of-Range Radio…………………………………………………………………………………………………46 6.4 Site Trunking Feature……………………………………………………………………………………………… 46 6.5 Site Search……………………………………………………………………………………………………………. 46 6.6 Locking or Unlocking Sites………………………………………………………………………………………. 47 6.7 Viewing the Current Site………………………………………………………………………………………….. 47 6.8 Changing the Current Site……………………………………………………………………………………….. 47
Chapter 7: Types of Radio Calls…………………………………………………………………. 48
7.1 Making Calls………………………………………………………………………………………………………….. 48 7.2 Receiving Calls………………………………………………………………………………………………………. 49 7.3 Making Priority Dispatch Calls………………………………………………………………………………….. 50
Chapter 8: Emergency Operation……………………………………………………………….. 51
8.1 Special Considerations for Emergency Operation………………………………………………………..51 8.2 Sending Emergency Alarms…………………………………………………………………………………….. 52 8.3 Sending Emergency Alarms with Emergency Calls………………………………………………………52 8.4 Exiting Emergency Operation…………………………………………………………………………………… 52 8.5 Remote Emergency………………………………………………………………………………………………… 53
8.5.1 Sending Remote Emergency to Specific Users………………………………………………. 53 8.5.2 Manually Refreshing the Remote Emergency List……………………………………………54 8.5.3 Receiving Remote Emergency…………………………………………………………………….. 54 8.6 Emergency Keep- Alive……………………………………………………………………………………………. 54 8.7 Emergency Beacon………………………………………………………………………………………………… 54 8.7.1 Sending Emergency Beacons……………………………………………………………………….54 8.7.2 Receiving Emergency Beacons……………………………………………………………………. 54 8.7.3 Viewing Received Emergency Beacon………………………………………………………….. 55
Chapter 9: Fireground…………………………………………………………………………………56
9.1 Entering Fireground Zone Channel (Conventional)……………………………………………………… 56 9.2 Responding to Evacuation Indicator………………………………………………………………………….. 56 9.3 Sending Evacuation Tone…………………………………………………………………………………………57
Chapter 10: Tactical Public Safety (Conventional Only)………………………………. 58
10.1 Using TPS Normal Transmission……………………………………………………………………………..58 10.2 Using TPS Emergency Transmission………………………………………………………………………. 58
4

MN009203A01-AD Contents
Chapter 11: Man Down (Fall Alert) ………………………………………………………………59
11.1 Radio Alerts When Man Down (Fall Alert) is Triggered………………………………………………. 59 11.2 Testing Man Down (Fall Alert)………………………………………………………………………………… 59 11.3 Exiting Man Down (Fall Alert)…………………………………………………………………………………. 60 11.4 Reinitiating Man Down (Fall Alert)…………………………………………………………………………… 60
Chapter 12: Secure Operations………………………………………………………………….. 61
12.1 Switching Between Secure and Clear Transmission………………………………………………….. 61 12.2 Encryption…………………………………………………………………………………………………………….61
12.2.1 Multikey Feature………………………………………………………………………………………. 61 12.2.2 MDC OTAR (Conventional Only)………………………………………………………………… 62 12.2.3 Infinite UKEK Retention…………………………………………………………………………….. 62 12.2.4 Hear Clear………………………………………………………………………………………………..62 12.2.5 Loading Encryption Keys…………………………………………………………………………… 63 12.2.6 Selecting Encryption Keys…………………………………………………………………………. 63 12.2.7 Selecting Keysets…………………………………………………………………………………….. 63 12.2.8 Erasing Encryption Keys…………………………………………………………………………….63 12.2.9 Requesting Over-the-Air Rekey………………………………………………………………….. 64
Chapter 13: Scan………………………………………………………………………………………..65
13.1 Turning Scan On or Off…………………………………………………………………………………………..65 13.2 Making Dynamic Priority Change (Conventional Scan Only)………………………………………. 65 13.3 Deleting Nuisance Channel……………………………………………………………………………………. 65 13.4 Restoring Nuisance Channels………………………………………………………………………………… 65
Chapter 14: Scan Lists………………………………………………………………………………. 67
14.1 Managing the Scan List…………………………………………………………………………………………. 67
Chapter 15: Connectivity…………………………………………………………………………….68
15.1 SmartConnect……………………………………………………………………………………………………….68 15.2 Wi- Fi…………………………………………………………………………………………………………………… 68 15.3 Bluetooth®…………………………………………………………………………………………………………… 68
15.3.1 Turning Bluetooth On or Off………………………………………………………………………..69 15.3.2 Searching and Pairing the Bluetooth Device………………………………………………… 69 15.3.3 Turning Bluetooth Audio On or Off……………………………………………………………….69 15.3.4 Viewing and Clearing the Bluetooth Enabled Device Information……………………..69 15.4 ASTRO 25 (P25) Programming Over Project 25 (POP25)………………………………………….. 70 15.4.1 Responding to Upgrade Notifications………………………………………………………….. 70
Chapter 16: Location ………………………………………………………………………………….71
16.1 Turning Location On or Off…………………………………………………………………………………….. 71 16.2 Accessing Location………………………………………………………………………………………………..71 16.3 Selecting Location Formats……………………………………………………………………………………. 72
5

MN009203A01-AD Contents
16.4 Managing Waypoints…………………………………………………………………………………………….. 72 16.5 Location Feature in Emergency Mode………………………………………………………………………73 16.6 Peer-Location on the Display (ASTRO Conventional)…………………………………………………73 16.7 MGRS Coordinates………………………………………………………………………………………………..74
Chapter 17: Mission Critical Geofence (ASTRO 25 Trunking)………………………. 75
17.1 Entry to the Geofence Area……………………………………………………………………………………. 75 17.2 Entry to Mission Critical Geofence……………………………………………………………………………76 17.3 Exit from Mission Critical Geofence………………………………………………………………………….76
Chapter 18: Contacts…………………………………………………………………………………. 77
18.1 Viewing Contact Details………………………………………………………………………………………….77
Chapter 19: Recent Calls…………………………………………………………………………….78
19.1 Viewing Recent Calls……………………………………………………………………………………………..78 19.2 Deleting Calls………………………………………………………………………………………………………..78
Chapter 20: Sending Status……………………………………………………………………….. 80 Chapter 21: Call Alert Paging………………………………………………………………………81
21.1 Sending Call Alert Page………………………………………………………………………………………….81 21.2 Receiving Call Alert Page………………………………………………………………………………………. 82
Chapter 22: Automatic Registration Service……………………………………………….. 83
22.1 Selecting ARS Mode………………………………………………………………………………………………83
Chapter 23: User Login Feature…………………………………………………………………..84
23.1 Logging In or Out of the User Login Feature…………………………………………………………….. 84 Logging In the User Login Feature……………………………………………………………………….. 84 Logging Out of the User Login Feature…………………………………………………………………..84
Chapter 24: Text Messaging Service……………………………………………………………86
24.1 TMS Status Icons…………………………………………………………………………………………………. 86 24.2 Accessing Messages…………………………………………………………………………………………….. 87
Chapter 25: Monitor Feature………………………………………………………………………. 88
25.1 Monitoring Channels………………………………………………………………………………………………88 25.2 Monitoring Conventional Mode……………………………………………………………………………….. 88
Chapter 26: Remote Monitor………………………………………………………………………. 90 Chapter 27: Transmit Inhibit………………………………………………………………………..91
27.1 Enabling or Disabling Transmit Inhibit……………………………………………………………………… 91 27.2 Smart PTT (Conventional Only)……………………………………………………………………………….91
Chapter 28: Dynamic Regrouping (Trunking Only) ………………………………………93
28.1 Classification of Regrouped Radios………………………………………………………………………….93 28.2 Requesting a Reprogram (Trunking Only)…………………………………………………………………93
Chapter 29: Dynamic Zone Programming…………………………………………………… 94
6

MN009203A01-AD Contents
29.1 Selecting Channels in the Dynamic Zone………………………………………………………………….94 29.2 Deleting Channels in the Dynamic Zone………………………………………………………………….. 94
Chapter 30: Zone-to-Zone Cloning……………………………………………………………… 95
30.1 Cloning Zones……………………………………………………………………………………………………….95
Chapter 31: Radio Kill ………………………………………………………………………………..96
31.1 Using Direct Kill to Kill Your Own Radio…………………………………………………………………… 96
Chapter 32: Radio Inhibit…………………………………………………………………………….97 Chapter 33: Switching between Repeater and Direct Operation…………………… 98 Chapter 34: Voice Announcement……………………………………………………………….99 Chapter 35: Site Selectable Alerts……………………………………………………………..100
35.1 Sending Site Selectable Alert Notification………………………………………………………………. 100 35.2 Stopping Site Selectable Alert Notification……………………………………………………………… 100
Chapter 36: Additional Performance Enhancement…………………………………… 102
36.1 ASTRO 25 Enhanced Data……………………………………………………………………………………102 36.2 Dynamic System Resilience…………………………………………………………………………………. 102 36.3 Encrypted Integrated Data…………………………………………………………………………………….102 36.4 SecureNet…………………………………………………………………………………………………………..102 36.5 P25 Digital Vehicular Repeater System…………………………………………………………………..102
Chapter 37: Accessories………………………………………………………………………….. 103
7

MN009203A01-AD List of Figures
List of Figures
Figure 1: Radio Overview……………………………………………………………………………………………………….. 21 Figure 2: Keypad Overview…………………………………………………………………………………………………….. 22 Figure 3: Home Screen Display………………………………………………………………………………………………..32
8

MN009203A01-AD List of Tables
List of Tables
Table 1: Radio Overview Description……………………………………………………………………………………….. 21 Table 2: Keypad Overview……………………………………………………………………………………………………… 23 Table 3: Assignable Radio Functions……………………………………………………………………………………….. 23 Table 4: ViQi Basic Voice Control Commands…………………………………………………………………………… 26 Table 5: ViQi Virtual Partner Queries……………………………………………………………………………………….. 27 Table 6: Home Screen Overview Description……………………………………………………………………………..32 Table 7: Status Icons………………………………………………………………………………………………………………33 Table 8: LED Indications………………………………………………………………………………………………………… 36 Table 9: Intelligent Lighting Indicators………………………………………………………………………………………. 37 Table 10: Transmit and Receive Indicators……………………………………………………………………………….. 37 Table 11: Emergency Operation Scenarios………………………………………………………………………………..51 Table 12: TMS Status Icons……………………………………………………………………………………………………. 86 Table 13: TMS Inline Icons………………………………………………………………………………………………………86
9

MN009203A01-AD Legal and Support
Legal and Support
Intellectual Property and Regulatory Notices
Copyrights
The Motorola Solutions products described in this document may include copyrighted Motorola Solutions computer programs. Laws in the United States and other countries preserve for Motorola Solutions certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola Solutions computer programs contained in the Motorola Solutions products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola Solutions. No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc.
Trademarks
MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.
License Rights
The purchase of Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola Solutions, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Open Source Content
This product may contain Open Source software used under license. Refer to the product installation media for full Open Source Legal Notices and Attribution content.
European Union (EU) and United Kingdom (UK) Waste of Electrical and Electronic Equipment (WEEE) Directive
The European Union’s WEEE directive and the UK’s WEEE regulation require that products sold into EU countries and the UK must have the crossed-out wheelie bin label on the product (or the package in some cases). As defined by the WEEE directive, this crossed-out wheelie bin label means that customers and end-users in EU and UK countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU and UK countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country.
Disclaimer
Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a specific system, or may be dependent upon the characteristics of a specific mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola Solutions contact for further information.
10

MN009203A01-AD Legal and Support © 2023 Motorola Solutions, Inc. All Rights Reserved
Legal and Compliance Statements Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola Solutions reserves the right to change any products to improve readability, function, or design. Motorola Solutions does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others.
Declaration of Conformity
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party Name: Motorola Solutions, Inc. Address: 2000 Progress Pkwy, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product: Model Name: APX N50 conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a)
Class B Digital Device
As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and
11

MN009203A01-AD Legal and Support
2 This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio or TV technician for help.
For country code selection usage (WLAN devices)
NOTE: The country code selection is for non-US model only and is not available to all US models. Per FCC regulation, all Wi-Fi products marketed in the US must be fixed to US operation channels only.
Industry Canada WLAN Statement
CAUTION: 1 The device for operation in the band 5150­5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
2 The maximum antenna gain permitted for devices in the bands 5250­5350 MHz and 5470­ 5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
3 The maximum antenna gain permitted for devices in the band 5752­5850 MHz shall be such that the equipment still complies with e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate.
4 The worst case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2 (3) shall be clearly indicated.
5 User should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250­5350 MHz and 5650­5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Important Safety Information
RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios
CAUTION: This radio is restricted to Occupational use only.
Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations.
For a list of Motorola Solutions-approved antennas, batteries, and other accessories, visit the following website:
12

MN009203A01-AD Legal and Support
https://www.motorolasolutions.com Any modification to this device, not expressly authorized by Motorola Solutions, may void your authority to operate this device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter is approved by Industry Canada to operate with a Motorola Solutions-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Notice to Users (FCC)
This device complies with Part 15 of the FCC rules per the following conditions: · This device may not cause harmful interference. · The device must accept any interference received, including interference that may cause undesired
operation. · Changes or modifications made to this device, not expressly approved by Motorola Solutions, could
void the authority of the user to operate this equipment.
FCC Licensing Information
This device complies with Parts 90 and 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the condition that this device does not cause harmful interference. The radio operates on radio frequencies that are regulated by the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159. To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed, or have questions, use the following contact information. Fax
Contact the Fax-On-Demand system at 1-202-418-0177 Mail
Call the FCC forms hotline at 1-800-418-FORM or 1-800-418-3676 Contact
For questions regarding FCC license, contact 1-888-CALL-FCC, 1-888-225-5322, or http:// www.fcc.gov. Before filling out your application, you must decide which frequency you can operate on. For questions on determining the radio frequency, call Motorola Solutions Product Services at: 1-800-448- 6686. Changes or modifications not expressly approved by Motorola Solutions may void the user authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component such as crystal, semiconductor, and others not authorized by the FCC equipment authorization for this radio could violate FCC rules.
NOTE: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.
13

MN009203A01-AD Legal and Support

Applying for Canadian License
The operation of your Motorola Solutions radio is subject to the Radio communications Act and must comply with rules and regulations of the Federal Government’s department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment.
Prerequisites: Obtain the latest Canadian License Application form at http://www.ic.gc.ca/ic_wppa.htm.
Procedure: 1 Fill in the items as per the instructions. Be sure to print legibly. If you need additional space for any item, use the reverse side of the application. 2 Make a copy of your files. 3 Prepare a cheque or money order payable to the “Receiver General for Canada”, for an amount for each radio purchased. The license is renewed on April 1st each year, and issued for a period of 12 months. 4 Mail your completed application along with your cheque or money order to the closest Industry Canada District office.
Limited Warranty

MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS

I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
MOTOROLA SOLUTIONS, INC. (“MOTOROLA”) warrants the MOTOROLA SOLUTIONS manufactured Communication Products listed below (“Product”) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

APX N50 Product Accessories

One (1) Year One (1) Year

MOTOROLA SOLUTIONS, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA SOLUTIONS.
This express limited warranty is extended by MOTOROLA SOLUTIONS to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA SOLUTIONS. MOTOROLA SOLUTIONS assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA SOLUTIONS.
Unless made in a separate agreement between MOTOROLA SOLUTIONS and the original end user purchaser, MOTOROLA SOLUTIONS does not warrant the installation, maintenance or service of the Product.
MOTOROLA SOLUTIONS cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA SOLUTIONS which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded

14

MN009203A01-AD Legal and Support
from this warranty. Because each system which may use the Product is unique, MOTOROLA SOLUTIONS disclaims liability for range, coverage, or operation of the system as a whole under this warranty.
MOTOROLA SOLUTIONS offers the following optional extended service contracts.
DEVICE MANAGED SERVICES (DMS) ACCIDENTAL DAMAGE
Provides for extended hardware repair coverage INCLUDING CHEMICAL, LIQUID, FIRE, AND OTHER PHYSICAL DAMAGE. Accidental damage coverage is available in conjunction with MOTOROLA SOLUTIONS’S standard Commercial Warranty and starts from the FIRST DAY the radio is put into use. Service performed under this plan consists of repair or replacement of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay the inbound shipping charges only with use of the MOTOROLA SOLUTIONS designated delivery service. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS’S normal shipping methods.
DEVICE MANAGED SERVICES (DMS) STANDARD HARDWARE
Provides extended hardware normal wear and tear repair coverage beginning AFTER MOTOROLA SOLUTIONS’S standard Commercial Warranty period expires. Service performed under this plan consists of repair of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS’S normal shipping methods.
II. GENERAL PROVISIONS:
This warranty sets forth the full extent of MOTOROLA SOLUTIONS’S responsibilities regarding the Product. Repair, replacement, or refund of the purchase price, at MOTOROLA SOLUTIONS’s option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA SOLUTIONS BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.
III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY.
This warranty gives specific legal rights, and there may be other rights, which may vary from state to state.
IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA SOLUTIONS through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA SOLUTIONS at 1-800-927-2744 US/Canada.
15

MN009203A01-AD Legal and Support
V. WHAT THIS WARRANTY DOES NOT COVER:
1 Defects or damage resulting from use of the Product in other than its normal and customary manner.
2 Defects or damage from misuse, accident, water, or neglect.
3 Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment.
4 Breakage or damage to antennas unless caused directly by defects in material workmanship.
5 A Product subjected to unauthorized Product modifications, disassembles, or repairs (including, without limitation, the addition to the Product of non- MOTOROLA SOLUTIONS supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA SOLUTIONS’s normal warranty inspection and testing of the Product to verify any warranty claim.
6 Product which has had the serial number removed or made illegible.
7 Rechargeable batteries if:
· any of the seals on the battery enclosure of cells are broken or show evidence of tampering.
· the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified.
8 Freight costs to the repair depot.
9 A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA SOLUTIONS’s published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA SOLUTIONS.
10 Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product.
11 Normal and customary wear and tear.
VI. PATENT AND SOFTWARE PROVISIONS:
MOTOROLA SOLUTIONS will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA SOLUTIONS will pay those costs and damages finally awarded against the end user purchaser in any such suit, which are attributable to any such claim, but such defense and payments are conditioned on the following:
1 that MOTOROLA SOLUTIONS will be notified promptly in writing by such purchaser of any notice of such claim,
2 that MOTOROLA SOLUTIONS will have sole control of the defense of such suit and all negotiations for its settlement or compromise, and
3 should the Product or parts become, or in MOTOROLA SOLUTIONS’ opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA SOLUTIONS, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non- infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA SOLUTIONS.
MOTOROLA SOLUTIONS will have no liability with respect to any claim of patent infringement, which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA SOLUTIONS, nor will MOTOROLA SOLUTIONS have any liability for the use of ancillary equipment or software not furnished by MOTOROLA SOLUTIONS,
16

MN009203A01-AD Legal and Support
which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA SOLUTIONS with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA SOLUTIONS certain exclusive rights for copyrighted MOTOROLA SOLUTIONS software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA SOLUTIONS software. MOTOROLA SOLUTIONS software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA SOLUTIONS software or exercise of rights in such MOTOROLA SOLUTIONS software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA SOLUTIONS patent rights or copyrights.
VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, U.S.A.
VIII. For Australia Only
This provision applies to products and services supplied by Motorola Solutions to consumers within the meaning of the Australian Consumer Law. This warranty is given by Motorola Solutions Australia Pty Limited (ABN16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. For major failures with the service, you are entitled: · To cancel your service contract with us: and · To a refund for the unused portion, or to compensation for its reduced value. You are entitled to choose a replacement or refund for a major failure with goods. If a failure with the goods or service does not amount to a major failure, you are entitled to have the failure rectified in a reasonable time. If this is not done, you are entitled to a refund for the goods, and to cancel the contract for the service and obtain a refund of any unused portion. You are also entitled to be compensated for any other reasonably foreseeable loss or damage from a failure in the goods or service. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: https://www.motorolasolutions.com/en_xa/support.html for current warranty terms.
17

MN009203A01-AD Read Me First

Read Me First
This User Guide covers the basic operation of the radio.
Notations Used in This Manual
Notations such as Warning, Caution, and Notice are used throughout the text in this publication. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.
WARNING: An operational procedure, practice, or condition, and so on, which can result in injury or death if not carefully observed.
CAUTION: An operational procedure, practice, or condition, and so on, which can result in damage to the equipment if not carefully observed.
NOTE: An operational procedure, practice, or condition, and so on, which is essential to emphasize.

The following special notations identify certain items.

Example
Home button or Phon

Description Buttons and keys are shown in bold print or as an icon.
Menu entries are shown similar to the way that they appear on the display of the radio. This means “Press the right side of the 4-Way Navigation button.”

This means that the content with this icon is designated for radio with Volume Control Knob and 16­Position Select Knob.

What Your Dealer or System Administrator Can Tell You
Your dealer or system administrator can customize your radio to your specific needs. If the radio is to be operated in extreme temperatures (less than -30 °C or more than +60 °C), check with your system administrator for the correct radio settings.
You can consult your dealer or system administrator about the following:
· Is your radio programmed with any preset conventional channels?
· Which buttons have been programmed to access other features?
· What optional accessories suit your needs?
NOTE: Specifications vary for different radio models. For more information, contact your system administrator.

Software Version
All the features described in the following sections are supported by the software version R31.00.00 or later.
Contact your system administrator for more details of all the supported features.

18

MN009203A01-AD Radio Care
Chapter 1
Radio Care
Proper radio usage and care ensure efficient operation and long life of the product. CAUTION: Use the radio according to the following recommendations and warnings. · Never obstruct or cover the vent port, even with a label. · Ensure that no oily substances come in contact with the vent port. · Your radio is designed to be submerged to a maximum depth of 6 feet and maximum time of 2 hours. Exceeding either maximum limit may result in damage to the radio. · The radio with antenna attached properly is submersible to a maximum depth of 1 meter (3.28 feet) and a maximum submersion time of 30 minutes. Exceeding either maximum limit or use without antenna may result in damage to the radio. · If the radio battery contacts are exposed to water without the battery attached, dry and clean the radio battery contacts before attaching a battery to the radio. Turn the radio over with the battery contact facing down and shake the radio so any trapped water can escape. A short circuit of the contacts could occur if they are not dried properly. · If the radio has been submerged in water, shake the radio to remove any water that is trapped inside the speaker grille and microphone port. Otherwise, the water decreases the audio quality of the radio. · If an accessory is not attached to the radio, ensure that the accessory connector cover is attached to the radio side accessory connector. · If the radio is submerged or exposed to a high force water spray, such as from a hose, remove the accessory or accessory connector cover immediately and ensure that no water is forced into the accessory connector/radio interface. Rinse and dry the area and re-attach the accessory or accessory connector cover if leakage occurs. · If the radio is exposed to a corrosive environment, such as salt water or corrosive gases or liquids, rinse and clean the radio immediately to prevent damage to radio materials, especially plated surfaces. Remove the battery and the antenna before cleaning. · Do not disassemble the radio as you could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. · Only Underwriter Laboratory (UL) approved service centers can open and service UL certified radios. Opening or repairing at unauthorized locations invalidates hazardous location rating of the radio. · Do not pound, drop, or throw the radio unnecessarily. · Turn off the radio when charging the radio using a wall-mounted charger. Otherwise, the Fall Alert and Emergency may be accidentally triggered. · When cleaning the radio, do not use a high-pressure jet spray as this may exceed the depth pressure and cause water to leak into the radio.
1.1
Cleaning Your Radio
CAUTION: Do not use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures. Do not submerge the radio in the detergent solution.
19

MN009203A01-AD Chapter 1 : Radio Care To clean the external surfaces of your radio, perform the following: Procedure:
1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, shortbristled brush, making sure that
excess detergent does not get entrapped near the connectors, controls, or crevices. 3 Rinse and then dry the radio thoroughly with a soft, lint-free cloth. 4 Clean battery contacts with a lint-free cloth to remove dirt or grease. 1.2
Radio Service and Repair
Proper repair and maintenance procedures ensure efficient operation and long- life of this radio. A Motorola Solutions maintenance agreement provides expert service to keep the radio and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola Solutions to support maintenance services. Through its maintenance and installation program, Motorola Solutions makes the finest service available to those desiring reliable continuous communications on a contract basis. For a contract service agreement, contact your nearest Motorola Solutions service or sales representative, or an authorized Motorola Solutions dealer. 1.3
Battery Recycling and Disposal
In the U.S. and Canada, Motorola Solutions participates in the nationwide Call2Recycle program for battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, go to http://www.call2recycle.org/ or call 1-800-8BATTERY. This website and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies.
20

Chapter 2
Radio Overview
Figure 1: Radio Overview

1
2
3 14

4

13

5

12

11 6

7 10
8
9

MN009203A01-AD Radio Overview
19 18 17 16 15

Table 1: Radio Overview Description

Number 1

Name Antenna

2

Channel Selector knob

3

On/Off/Volume Control knob

4

Status LED

5

3-Dot Programmable button

6

Push-to-Talk (PTT) button

7

1-Dot Programmable button

8

2-Dot Programmable button

Description
Allows you to transmit and receive electromagnetic waves during transmitting and receiving.
Allows you to select channel.
Allows you to turn on or off the radio, and adjust the volume.
Provides operating status.
Programmable button of an assignable radio function.
Allows you to execute voice operations.
Programmable button of an assignable radio function.
Programmable button of an assignable radio function.

21

MN009203A01-AD Chapter 2 : Radio Overview

Number 9

Name Speaker

10

Keypad

11

Display

12

Digital Mic 2

13

Top Light Bar

14

Top (Orange) button

15

Charging Contacts

16

Battery

17

Accessory Connector

18

Belt Clip Bracket

19

Digital Mic 1

2.1
Keypad Overview
Figure 2: Keypad Overview

Description Outputs tones and audio that are generated by the radio. Allows menu navigation and interface selection. The radio display screen. Allows your voice to be sent when PTT or voice operations are activated. Provides indication that a radio event has occurred. Allows you to turn on and off Emergency Operations. Besides the Emergency Operation, this button can also be configured for other features. Charging point for the battery. Provides battery power for your radio. Allows you to connect accessories to your radio. Allows you to attach belt clip. Noise Cancellation Microphone.
1

2

6

5

3

4

22

MN009203A01-AD Chapter 2 : Radio Overview

Table 2: Keypad Overview

Number 1 2 3

Button Name Menu Select buttons Home button Programmable button 1 (P1)

4

Programmable button 2 (P2)

5

4-Way Navigation buttons

6

Notification button

Description
Press to access the corresponding menu.
Press to return to Home screen.
This button is programmable using the Customer Programming Software (CPS).
This button is programmable using the CPS.
Press up, down, left, and right to navigate through your options. At the Home screen, press the left or right navigation button to display the required menu items.
This button is programmable using the CPS.

2.2
Programmable Radio Functions
Your system administrator can program the programmable buttons or switches as shortcuts to radio functions depending on the duration of a button press. Contact your system administrator to learn more about the radio functions assigned to the programmable buttons and switches of your radio.

Table 3: Assignable Radio Functions

Function Audio Playback

Description
To play the last saved call audio followed by other saved audio in the sequence from oldest to newest.
To save the received call audio into your radio, press and hold the button.

Basic Voice Control Beacon Bluetooth On/Off
Bluetooth Configuration Bluetooth Audio Reroute
Bluetooth Headset PTT Bluetooth Inquiry On/Off Call Alert Call Response Channel Announcement

Activates voice commands by pressing and holding.
Allows you to check the details of any recently received Emergency Beacons.
To turn on or off the Bluetooth, press the button.
To clear all the Bluetooth devices information, press and hold the button.
Allows you to access the Bluetooth menu.
Allows you to toggle the audio route between the radio speaker or the Remote Speaker Microphone and the Bluetooth headset.
Enables the Bluetooth Headset microphone.
Enables the Bluetooth Search feature.
Allows the radio to function like a pager, or helps you verify if a radio is active on the system.
Allows you to answer a private call or phone call.
Allows you to hear the Voice Announcement audio file that is assigned to the radio’s current channel/mode.

23

MN009203A01-AD Chapter 2 : Radio Overview

Function Channel Up/Down Contacts Dual Tone Multiple Frequency (DTMF) Tone Dynamic Priority (Conventional Only) Emergency Info
Internet Protocol (IP) Keypad/Control Lock Light/Flip Location
Man Down Clear Message Mode Select (MS01­ MS13)
Monitor (Conventional Only) Multiple Private Line (Conventional Only) Nuisance Delete
Phone Private Call (Trunking Only) Private Line Disable (Conventional Only) Priority Channel PTT

Description
Allows you to scroll up or down to other channels within the current Zone.
Allows you to access the Contacts menu.
Allows you to send out DTMF code of the assigned DTMF value. For example, when DTMF Tone 9 is selected, you can send out DTMF Tone 9.
Allows any channel in a Scan List (except for a Priority-One channel) to temporarily replace the Priority-Two channel.
Allows you to send or cancel Emergency Alarm to the dispatcher.
Allows you to display the Radio Information, Internet Protocol (IP) Display, SIM Status, Control Assignments and Soft ID (if enabled).
Allows you to display the IP address.
Toggles the keypad/control to lock or unlock.
To turn on the display backlight on and off, press the button.
Displays the current location (latitude, longitude, time, and date), and also the distance and bearing to another location, or toggles GPS/Location between on and off.
Allows you to clear and deactivate the Man Down (Fall Alert) Emergency mode alarm.
Allows you to access the message list.
To change to the preset Mode Select zone and channel, press the button.
When the Preconfigurable Preset Zone and Channel field is enabled, to save the current zone and channel to one of the Mode Select menus, press and hold the preferred Mode Select menu.
Monitors a selected channel for all radio traffic until the function is disabled.
Allows you to access the Multiple Private Line lists.
Temporarily removes an unwanted channel from scan list, except for priority channels and the designated transmit channel.
Allows you to make and receive calls similar to standard phone calls.
Allows you to dial the programmed ID (number) and initiate the Private Call.
Allows you to adjust squelch level of the radio between level 0 and 15 when you press and hold the button.
If in Scan Mode and Priority Member 1 Scan List Member is in the scan list of the current channel, the radio keys up on the Priority 1 Scan List Member channel, therefore allowing

24

MN009203A01-AD Chapter 2 : Radio Overview

Function
Priority Dispatch Radio Profiles
Recent Calls
Rekey Request Remote Emergency
Repeater Access Button (RAB) (Conventional Only) Reprogram Request (Trunking Only) Request-To-Talk (Conventional Only) Scan
Select Call Sensor
Site Display/Search (Trunking Only)
Site Lock/Unlock (Trunking Only) Status (Trunking Only) Talkaround/Direct (Conventional Only) Talkgroup (Conventional Only) Text Messaging Service (TMS)
Third Party
TMS Query
TMS Quick Text Transmit Power Level
Unprogrammed

Description
transmission of voice communication. Otherwise, the radio blocks the transmission and sounds the Talk Prohibit Tone. Allows you to call the dispatcher on a different talkgroup. Allows you to access a set of programmed visual and audio settings of the radio. Allows easy access to the list of calls recently received or made. Notifies the dispatcher that a new encryption key is needed. Activates the Remote Emergency feature for an authorized user to initiate the Emergency feature on a target radio without target user intervention. Allows you to manually send a repeater access codeword.
Notifies the dispatcher that a new dynamic regrouping assignment is needed. Notifies the dispatcher that you want to send a voice call.
To turn on or off the scan function, press the button.
To enable Scan List Programming and selects the scan list for editing, press and hold the button.
Calls an assigned radio. Allows you to select the time of the Sensor Event Disable Time operation. To display the current site ID and Received Signal Strength Indicator (RSSI) value.
To perform site search for Automatic Multiple Site Select (AMSS) or SmartZone operation, press and hold the button. Allows your radio to lock onto a specific site. Sends data calls to the dispatcher about a predefined status. Toggles between using a repeater or communicating directly with another radio. Allows a call from an individual radio to a group of radios. Allows you to access the Text Messaging Service (TMS) menu. Allows you to initiate functionality in third-party accessories, such as compatible Whelen® Sirens. Launches a list of predefined short text messages only after logging in with Two-Factor Authentication. Selects a predefined message. Toggles between the power levels at which your radio transmits. Select this feature for a radio button that is not in use.

25

MN009203A01-AD Chapter 2 : Radio Overview

Function User
Voice Mute
Volume Set Tone

Description
Allows you to log on to the server with a personally identifiable user name.
Allows you to mute the voice transmission of the current zone and channel.
Sets the volume set tone.

2.3
ViQi
ViQi allows you to manage your radio and perform information lookups using voice commands. This feature is purpose-built for easier access to features.
You are able to operate the radio with your voice using the following commands.

Table 4: ViQi Basic Voice Control Commands

Feature Battery

Examples To identify your battery level, say the following command: · “Battery level”

Channel

To identify your current channel, say the following command: · “Channel”

Home Channel

To change to your home channel, say the following command: · “Go to home”

Preset Profile

To change the preset of your radio, say “Preset ”, The available Preset number is from <1> to <7>.
To change the profile of your radio, say the following commands: · “Default profile” · “Loud audio profile” · “Surveillance profile”

Scan

To start or stop scanning, say the following commands: · “Start scanning” · “Stop scanning”

Volume

To change the volume level of your radio, say one of the available commands according to required volume levels: · ­ 10%
· ­ 50%
· ­ 100%

Zone

To identify your current zone, say the following command: · “Zone”

ViQi Virtual Partner

To initiate ViQi Virtual Partner, say the following command: · “Hey ViQi”

26

MN009203A01-AD Chapter 2 : Radio Overview

Feature List of Voice Commands

Examples To view the list of voice commands, say the following command: · “Go to help”

ViQi Virtual Partner
ViQi Virtual Partner helps you to look up information such as license plate, driver’s license, and Vehicle ID Number (VIN), and she responds with a result to your query.

Table 5: ViQi Virtual Partner Queries
The following table shows the queries supported by the ViQi Virtual Partner feature and their respective commands. Use the following commands followed by the supported query instructions to initiate ViQi Virtual Partner:
· “Look up…”
· “Check…”
· “Run a…”

Query License plate

Examples “Run a license plate ” “Check a license plate” “Look up license plate ”

Driver’s license

“Run a driver’s license ”
“Check the state of driver’s license ”
“Look up driver’s license”

Vehicle Identification Number

“Check Vehicle Identification Number ”
“VIN check ”
“Run a VIN”
NOTE: You can use variations such as , , and .

Own Location

“Where am I?” “Can I get my exact location?” “Am I still at the ?”
NOTE: ViQi will ask for more information to complete the query.

Target Location

“Where is ?” “Tell me where is”
NOTE: ViQi will ask for more information to complete the query.

27

MN009203A01-AD Chapter 2 : Radio Overview You are also able to receive and listen to LMR and Virtual Partner over broadband audio simultaneously. These audio mixing is configurable and must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. 2.3.1
Activating Basic Voice Control
Prerequisites: Configure a programmable button for basic voice control. Procedure:
1 Press and hold the programmed Basic Voice Control button. 2 Speak your command into the radio mic. 3 Release the programmed Basic Voice Control button. Basic voice control is activated and the radio operates according to the voice command. 2.3.2
Using ViQi Virtual Partner
Procedure: 1 Press and hold the programmed ViQi button. 2 After you hear a tone, speak your request into the microphone. 3 Release the assigned programmable button and wait for ViQi to respond. 4 Throughout your session, repeat steps step 1 through step 3 when responding to ViQi. Depending on your query, you can also say the following requests: · To play the available results, say “Play results”. · To request for more details, say “More details”. · To complete the Virtual Partner session, say “Complete”.
28

Chapter 3
Getting Started
This section provides instructions to prepare your radio for use.
3.1
Attaching and Removing the Battery
Attaching the Battery
Procedure: Slide the battery into the radio frame until the latches click into place.
Removing the Battery
Procedure: 1 Turn off the radio. 2 Lift the latch at the bottom of the radio. 3 Remove the battery from the radio.
3.2
Attaching and Removing the Antenna
Attaching the Antenna
Prerequisites: Ensure the radio is turned off before attaching the antenna. Procedure:
1 Set the antenna in the receptacle. 2 Turn the antenna clockwise to attach to the radio.
Removing the Antenna
Prerequisites: Ensure the radio is turned off before removing the antenna. Procedure:
1 Turn the antenna counterclockwise. 2 Remove the antenna from the receptacle.

MN009203A01-AD Getting Started

29

MN009203A01-AD Chapter 3 : Getting Started
3.3
Attaching and Removing the Accessory Connector Cover
The accessory connector is on the antenna side of the radio enables you to connect accessories to the radio.
NOTE: To prevent damage to the connector, shield it with the connector cover when not in use.
Attaching the Accessory Connector Cover
Procedure: 1 Insert the hook end of the cover into the slot above the connector. 2 Press the top of the cover downward to place it in the slot. 3 Rotate the thumbscrew clockwise.
Removing the Accessory Connector Cover
Procedure: 1 Rotate the thumbscrew counterclockwise until it disengages from the radio. NOTE: If the thumbscrew is too tight, use an allen wrench to loosen it.
2 Rotate and lift the connector cover to disengage it from the radio.
3.4
Attaching the Belt Clip
Procedure: Align the grooves of the belt clip with the radio and insert it until you hear a click.
3.5
Charging the Radio
Prerequisites: WARNING: To avoid possible explosion: · Do not replace the battery in any area labeled Hazardous Atmosphere. · Do not discard batteries in a fire.
When and where to use: Motorola Solutions-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola Solutions-authorized batteries and chargers available for use with your radio, see Accessories.
NOTE: When charging a battery attached to a radio, the radio must be turned off.
Procedure: 1 Turn off the radio while charging in a single or multi-unit charger.
30

MN009203A01-AD Chapter 3 : Getting Started 2 Place the radio in a Motorola Solutions-approved charger. The LED on the charger indicates the charging progress. For more information, see the Charger User Guide. 3.6
Turning the Radio On or Off
Prerequisites: Ensure that the battery is fully charged before the first use.
Turning the Radio On
Procedure: To turn on, turn the On/Off/Volume Control knob clockwise until you hear a click.
Turning the Radio Off
Procedure: To turn off, turn the On/Off/Volume Control knob counterclockwise until you hear a click.
3.7
Adjusting the Volume of the Radio
Procedure: 1 To increase the volume, rotate the On/Off/Volume Control knob clockwise. 2 To decrease the volume, rotate the On/Off/Volume Control knob counterclockwise.
31

MN009203A01-AD Chapter 4 : Home Screen Overview

Chapter 4
Home Screen Overview
Figure 3: Home Screen Display

1

2

6

3

4 5

Table 6: Home Screen Overview Description

Number 1

Name Dark Mode Status Bar

2

Bright Mode Status Bar

3

Radio Control Widget

4

Notification Widget

5

Menu Items

6

Time

Description
Dark mode status icons appear in the status bar to provide device status and feature notifications.
Bright mode status icons appear in the status bar to provide device status and feature notifications.
Displays the zone, channel, trunking status, and call state.
Displays the most recent text message notification.
Displays the programmed menu items.
The available time format is 12 hours (default) and 24 hours.

4.1
Status Indicators
This section explains the status indicators of the radio.

32

MN009203A01-AD Chapter 4 : Home Screen Overview

4.1.1
Status Icons
These icons appear at the status bar to provide device-specific information or status.

Table 7: Status Icons

Icon

Name Battery Level

Description
Indicates the remaining battery level of the radio. The icon blinks when the battery level drops to 10% or lower.

Broadband Network is Active Broadband Receiving

Steady The broadband system is available and connected.
Blinking The Automatic Registration Service (ARS) user login failed while in Broadband system.
The radio is receiving the broadband signal.

Broadband Transmitting

The radio is transmitting the broadband signal.

Broadband Receiving and Transmitting
Broadband with ARS User Logged In
Broadband Receiving while ARS User Logged In
Broadband Transmitting while ARS User Logged In
Broadband Receiving and Transmitting while ARS User Logged In Bluetooth® On
Bluetooth Connectivity

The radio is receiving and transmitting the broadband signal.
The ARS user logged on successfully with the broadband system.
The ARS user logged on successfully with the broadband system.
The radio is transmitting a broadband signal with the ARS user logged on.
The radio is receiving and transmitting broadband signals with the ARS user logged on.
The Bluetooth wireless technology is turned on and ready for connection.
Steady Bluetooth is connected to the external Bluetooth device.
Blinking The Bluetooth device is disconnected.

33

MN009203A01-AD Chapter 4 : Home Screen Overview

Icon

Name Call Received

Description The radio received a call.

Direct Mode
Global Positioning System (GPS) In-Call User Alert

The radio is configured for direct radio-to-radio communication in conventional operation. GPS is enabled and the signal is available.
The receiving audio turns off.

Data Activity

Data activity is present on the radio.

Regular Inverted

User Login Indicator (IP Packet Data)
Monitor

Steady The user is associated with the radio.
Blinking The device registration or user registration with the server failed due to an invalid username or pin.
Inverted The user is logged on to the secured IP packet data.
The selected channel is being monitored in conventional operation.

Roaming

The radio has roamed to and is registered to a foreign system.

Received Signal Strength Indicator (RSSI)
RSSI Out of Range

The number of bars represents the received signal strength of the current site in trunking mode.
The received signal is too far to be detected.

Receiving

The radio is receiving a call or data.

Transmitting

The radio is transmitting a call or data.

Satellite Network is Active

Steady The satellite system is available and connected.
Blinking The ARS user login failed while in the satellite system.

34

Icon

Name Satellite Receiving

MN009203A01-AD Chapter 4 : Home Screen Overview
Description The radio is receiving a satellite signal.

Satellite Transmitting

The radio is transmitting a satellite signal.

Satellite Receiving and Trans- The radio is receiving and transmitting satellite

mitting

signals.

Satellite with ARS User Logged In

The ARS user logged on successfully with the satellite system.

Satellite Receiving while ARS User Logged In

The ARS user logged on successfully with the satellite system.

Satellite Transmitting while ARS user Logged In

The radio is transmitting a satellite signal with the ARS user logged on.

Satellite Receiving and Transmitting while ARS User Logged In
SmartConnect Capable

The radio is receiving and transmitting satellite signals with the ARS user logged on.
The current channel is capable of supporting SmartConnect.

SmartConnect Connected

The current channel is currently connected through the SmartConnect feature.

Scan

The radio is scanning a scan list.

Priority Channel Scan Vote Scan

Steady The radio detects activity on the designated Priority-Two channel.
Blinking The radio detects activity on the designated Priority-One channel.
The Vote Scan feature is enabled.

Secure Operation
Advanced Encryption Standard (AES) Secure Operation

Steady The radio is operating in a secure channel.
Blinking The radio is receiving an encrypted voice call.
Steady The radio is operating in an AES-secure channel.

35

MN009203A01-AD Chapter 4 : Home Screen Overview

Icon

Name

Power Level High

Description
Blinking The radio is receiving an AES-encrypted voice call.
The radio is set at high power.

Power Level Low

The radio is set at low power.

Virtual Private Network (VPN) VPN is activated on the radio.

Wi-Fi Strength Wi-Fi Unavailable

Your radio is connected to a Wi-Fi network. The number of bars represents the signal strength of the Wi-Fi network.
Wi-fi network cannot be reached.

4.1.2
LED Indications
The LED indications represent the operational status of your radio. A qualified technician can permanently disable the LED indication by preprogramming it.

Table 8: LED Indications

Indication Solid red

Status Radio is transmitting.

Blinking red Double blinking red

Radio is transmitting at low battery condition or detects an incompatible battery.
Radio is transmitting an emergency alarm or call.

Rapid blinking red Solid yellow

Radio has failed the self-test upon powering up or encountered a fatal error.
Radio is receiving in both trunking and conventional clear mode.
NOTE: The yellow LED will illuminate only when the busy LED feature is enabled through Customer Programming Software (CPS).

Blinking yellow

Radio is receiving a secured transmission.

Solid green

Radio is powering up.

Blinking green

Radio is receiving an individual or telephone call.

36

MN009203A01-AD Chapter 4 : Home Screen Overview

4.1.3
Intelligent Lighting Indicators
This feature temporarily changes the color of the Top Light Bar and adds a color bar to the main display screen to help signal that a radio event has occurred.

Table 9: Intelligent Lighting Indicators

Backlight and Bar Color
Orange

Notification Emergency Alerts

Red

Critical Alerts

Green

Call Alerts

When
The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio initiates the Fall Alert (Man Down) Post- Alert timer. The radio battery is low. The radio is out of range. The radio enters Failsoft mode. The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio lost the Global Positioning System (GPS) signal or the GPS function fails. The radio receives a private call. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. The radio enters Geofence.

4.1.4
Transmit and Receive Indicators
The Transmit and Receive Indicator indicates the active call state of the radio.

Table 10: Transmit and Receive Indicators

Indicator

Light Bar Color Light Blue

Call State Open or Standby

Yellow

Receiving and Unmuted

37

MN009203A01-AD Chapter 4 : Home Screen Overview
Indicator

Light Bar Color Red

Call State Voice Transmission

Light Blue

Out of Range

Light Blue

Smart Connect

Gray

Unprogrammed

Gray

Receiving Frequency Error

38

MN009203A01-AD General Radio Operation

Chapter 5

General Radio Operation

This chapter explains the general operations of your radio.

5.1
Selecting Zones
A zone is a group of channels.
Procedure: 1 Press the Zone menu item. 2 Select the required zone and press Sel.

5.2
Selecting Channels
A channel is a group of radio characteristics, such as transmit or receive frequency pairs.
Procedure: Select channels by using the following options.

Option
Selecting radio channels using the Channel Selector knob
Selecting radio channels from the Menu

Actions
Rotate the Channel Selector knob to the required channel.
a Press the Chan menu item. b Select the required channel and press Sel.

5.2.1
Channel Error Message
If there is a channel error, your radio displays error messages on the Radio Control Widget.

Type Unprogrammed Fail 001

Description The mode is set to an unprogrammed channel. The selected channel is assigned to an incorrect frequency band.

5.3
Mode Select Feature
The Mode Select feature allows you to save the current zone and channel on your radio to one of the Mode Select feature menus (MS01­MS05) on a programmable side button (MS01­MS13).
When programmed, pressing the button changes the transmission to the saved zone and channel. When the Preconfigurable Preset Zone and Channel field is enabled, pressing and holding the

39

MN009203A01-AD Chapter 5 : General Radio Operation
preferred Mode Select menu saves the current zone and channel to one of the Mode Select menus. The radio displays MS0x is programmed.
NOTE: Your radio must be programmed for you to use this feature.
5.3.1
Saving Zones and Channels
You can save frequently used zones and channels to the programmable buttons. Prerequisites: Enable the Preconfigurable Preset Zone and Channel field. Procedure:
1 Toggle from your current zone and channel to the required zone and channel. 2 To save zones and channels to a button, press and hold the button you want to program.
If the zone and channel is saved, a tone sounds. If the Preconfigurable Preset Zone and Channel field is disabled, a negative tone sounds.
NOTE: Short press of the programmed button changes your current transmission to the zone and channel programmed in the button.
5.4
Selecting the Power Level
This feature enables you to select the power level at which your radio transmits. Power level Low enables a shorter transmitting distance and power consumption. Power level High enables a longertransmitting distance. Prerequisites: This feature must be programmed by a qualified radio technician. Procedure:
Switch to the required power level by pressing the Pwr menu item. The display shows Low power and the Power Level Low icon or the display shows High power and the Power Level High icon.
5.5
Selecting a Radio Profile
Procedure: 1 Press the Prfl menu item. 2 Select the required radio profile and press Sel.
5.6
Enabling and Disabling the Radio Alias
This feature allows you to display or hide the radio alias (name).
40

MN009203A01-AD Chapter 5 : General Radio Operation
Procedure: Enable or disable the radio alias by pressing the MyID menu item.
The display shows momentary Radio ID off, and the radio alias disappears from the Home screen or the display shows momentary Radio ID on, and the radio alias appears on the Home screen.
5.7
Adjusting the Display Backlight
You can enable or disable the radio display backlight as needed, if poor light conditions make the display or keypad difficult to read.
NOTE: The backlight setting also affects the Menu Select buttons and Navigation button backlighting accordingly. The backlight remains on for a programmed time before it automatically turns off completely or returns to the minimum backlight level.
Procedure: Perform one of the following actions: · To turn the backlight on or off, press the programmed Light/Flip button. · To turn the backlight on, press either the Menu Select or Navigation button, or any programmable radio controls or buttons.
5.8
Editing the Time and Date
Procedure: 1 Press the Clck menu item. 2 Press Edit. 3 Perform one of the following actions: · To save, select the required time and date. Press Ok. · To cancel, press Cncl. · To return to the home screen and discard your changes, press the Home button.
5.9
Locking and Unlocking the Controls
You can lock your radio keypad, programmable buttons, and knob or knobs to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suit your usage.
Procedure: 1 To lock the controls, press the programmed Keypad/Control Lock button. The display shows Kypd/Ctrl Lock.
2 To unlock the controls, press the button again.
5.10
Setting the Tones for Controls and Buttons
If needed, you can enable or disable the tones of navigation buttons and controls.
41

MN009203A01-AD Chapter 5 : General Radio Operation
Procedure: Turn the tones on or off by pressing the Mute menu item.
The display shows a notification message indicating if the tones are enabled or disabled. If the tones are enabled, you hear a short tone.
5.11
Setting the Voice Mute
This feature allows you to mute the voice transmission of the current zone and channel.
Procedure: Turn Voice Mute on or off by pressing the VMut menu item.
If Voice Mute is successfully turned on, your radio shows the following indications: · A short tone sounds. · The display shows Voice mute on. If Voice Mute is successfully turned off, your radio shows the following indications: · A short tone sounds. · The display shows Voice mute off.
5.12
Using the Time-Out Timer
This feature turns off the transmitter of your radio. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone.
NOTE: The default timer is 60 seconds. Contact your system administrator to adjust the timer duration.
Procedure: 1 Press and hold the PTT button longer than the programmed time.
The radio shows the following indications: · A tone sounds. · The transmission is cut off. · The LED extinguishes.
2 To reset the timer, release the PTT button. 3 To retransmit, press the PTT button.
The time-out timer restarts, and the red LED illuminates.
5.13
Adjusting the Squelch Level
The Adjustable Fine Tune Squelch feature allows you to adjust the desired squelch level of the radio between level 0 and 15.
42

MN009203A01-AD Chapter 5 : General Radio Operation

The following settings determine the types of call that you receive: · 0 ­ Squelch is open and all calls regardless of signal strength and background noise pass through. · Lower setting ­ Calls with low signal strength and higher than normal background noise pass
through. · Higher Setting ­ Calls with low signal strength and higher than normal background noise are filtered
out.
Procedure: 1 From the Home screen, press and hold the preprogrammed Private Line Disable button. The radio displays the Squelch menu.
2 To adjust the squelch level, perform one of the following actions: · Press – or +. · Press the Left or Right navigation button.
3 To return to the Home screen, press the Home button.
5.14
Conventional Squelch Operation
This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise.
Analog Options
Tone Private Line, Digital Private-Line, and carrier squelch is available and programmed per channel.

Option Carrier squelch Tone Private Line or Digital Private-Line

Result You hear all traffic on a channel. The radio responds only to your messages.

Digital Options
One or more of the following options can be programmed in your radio. For more information, contact your system administrator.

Option Digital Carrier-Operated Squelch Normal Squelch
Selective Switch

Result
You hear all digital traffic.
You hear any digital traffic having the correct network access code.
You hear any digital traffic having the correct network access code and correct talkgroup.

5.14.1
Setting Conventional Squelch Operation
Procedure: 1 Press the Sql menu item.

43

MN009203A01-AD Chapter 5 : General Radio Operation
2 Perform one of the following actions: · To increase the squelch volume, press +. · To decrease the squelch volume, press -.
3 To return to the selected channel, press the Home button.
5.15
Using the PL Disable Feature
This feature allows you to override any coded squelch that preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. When this feature is active, the Carrier Squelch status indicator is displayed.
Procedure: Turn on the PL Disable feature by pressing the programmed PL Disable button. One of the following results occurs: · The radio plays the active transmission on the channel. · If no activity is present, the radio is muted
5.16
Digital PTT ID Support
This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. The receiving radio and the dispatcher can view the ID, which consists of up to a maximum of eight characters. The ID number of your radio is also automatically sent every time you press the PTT button. This feature is preprogrammed per channel. For digital voice transmissions, the ID of your radio is sent continuously during the voice message.
5.17
General Radio Information
This menu item allows you to view general information of your radio. The available information are: · Radio Information · IP Information · Control Map · Certificates · IoT Status · Voice Commands
5.17.1
Accessing the General Radio Information
Procedure: 1 Press the Info menu item. 2 Perform one of the following actions:
44

MN009203A01-AD Chapter 5 : General Radio Operation · To view radio information, press Radio Info. · To view IP information, press IP Info. · To view Control Map, press Control Map. · To view Certificates, press Certificates. · To view IoT status, press IoT Status. · To view programmed voice commands, press Voice Commands.
45

MN009203A01-AD Chapter 6 : Trunking System Controls
Chapter 6
Trunking System Controls
This chapter explains the trunking system control features on your radio.
6.1
Operating in Failsoft System
The failsoft system ensures continuous radio communication during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. To continue in Failsoft and to communicate with other talkgroups, refer to the following procedure.
Procedure: 1 Rotate the Channel Selector knob to change to a different repeater frequency. 2 To call, press and hold the PTT button. 3 To listen, release the PTT button.
6.2
Imbalanced Coverage
Imbalanced coverage occurs when the radio is able to receive the control channel but is unable to transmit back to the system. The radio generates a periodic tone and displays No Comms.
6.3
Out-of-Range Radio
When your radio goes out of the range of the system, it can no longer lock onto a control channel. You hear a low-pitched tone and/or the display shows the currently selected zone/channel combination and Out of range notification. Your radio remains in this out-of-range condition until it locks onto a control channel or failsoft channel, or if it is turned off.
6.4
Site Trunking Feature
If the Zone Controller loses communication with any site, that site reverts to site trunking. When this occurs, you can communicate only with the radios within your trunking site. The display shows the currently selected zone/channel and the Site Trunking message.
6.5
Site Search
When searching for a site, your radio is inoperable. In the site search mode, your radio scans for trunked control channels but has yet to connect to the trunking system or reach other trunking states. Other trunking states are such as Out of Range and Imbalanced Coverage. The Searching site indicator alerts you that your radio is attempting to search for a valid trunked control channel.
46

MN009203A01-AD Chapter 6 : Trunking System Controls
6.6
Locking or Unlocking Sites
This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature must be used with caution because it inhibits roaming to another site in a wide-area system. Procedure:
1 Press the Site menu item. 2 Perform one of the following actions:
· To lock the site, press Lock. · To unlock the site, press Unlk. The display shows a notification to indicate if the site is locked or unlocked. The radio saves the new site lock state and returns to the Home screen. 6.7
Viewing the Current Site
Procedure: Press the programmed Site Displ/Srch button.
The display shows the name of the current site and corresponding received RSSI. 6.8
Changing the Current Site
Procedure: Press and hold the programmed Site Displ/Srch button.
The radio shows the following indications: · A tone sounds. · The display shows momentary Scanning site. When the radio finds a new site, it returns to the Home screen.
47

MN009203A01-AD Chapter 7 : Types of Radio Calls

Chapter 7

Types of Radio Calls
Your radio can make a Talkgroup, Private, Selective, and Telephone call in conventional and/or trunking mode.

Call Type
Talkgroup Call This feature is a point-to-multipoint call operation. Your radio must be configured as a member of the talkgroup for you to communicate within the talkgroup.
Private Call This feature is a call from one individual radio to another.
Selective Call This feature is a call from an individual radio to another individual radio with privacy.
Telephone Call This feature allows you to receive calls similar to standard phone calls from a landline phone.

Conventional Mode

Trunking Mode

SmartConnect

7.1
Making Calls

Procedure: 1 Make calls by using the following options.

Option Talkgroup Call
Private Call

Actions
a To transmit, press and hold the PTT button.
b Wait for the Talk Permit Tone. Then, speak into the microphone.
c To listen, release the PTT button.
NOTE: You cannot transmit longer than the preset Time-Out Timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a tone.
a Enter the Contacts page by pressing the Cnts menu item.

48

MN009203A01-AD Chapter 7 : Types of Radio Calls

Option Selective Call Telephone Call

Actions
b Select the required preprogrammed contact. c Start the call by pressing the PTT button. d To end the call, press Exit.
a Enter the Contacts page by pressing the Cnts menu item.
b Select the required preprogrammed contact. c Start the call by pressing the PTT button. d To end the call, release the PTT button.
a Press the Phon menu item. The display shows the last transmitted or received ID.
b To select the required ID, perform one of the following actions: · Press Cnts. · To go to the last dialed number, press LNum.
c To dial the phone number, press the PTT button. d To talk, press and hold the PTT button and speak into
the microphone. e To listen, release the PTT button.

7.2
Receiving Calls

Procedure: Receive calls by using the following options.

Option Talkgroup Call
Private Call

Actions
No action is required. Your radio automatically plays the transmission from the talkgroup call.
When you receive private calls, your radio shows the following indications: · A tone sounds. · The green LED blinks. · This display shows Call received, and the Call Re-
ceived icon blinks. a Respond by performing one of the following actions:
· To reject the call, press Exit. · To accept the call, press Resp. b To talk, press and hold the PTT button. c To listen, release the PTT button. d To end the call, press End.

49

MN009203A01-AD Chapter 7 : Types of Radio Calls

Option Selective Call
Telephone Call

Actions
For incoming Selective Calls, your radio automatically plays the transmission from the call. a Respond to the call by pressing and holding the PTT
button. b Speak into the microphone.
Perform one of the following actions: · To receive call, press Call Response. · To talk, press and hold the PTT button. · To listen, release the PTT button.

7.3
Making Priority Dispatch Calls
The Priority Dispatch feature allows you to call the dispatcher on a different talkgroup when a talkgroup is congested. This talkgroup is called the Priority Talkgroup. Each trunking talkgroup can have an assigned Priority Talkgroup. Priority Dispatch is not available in Emergency operations. The Scan feature is suspended when Priority Dispatch is initiated.
Prerequisites: The dispatch console that supports this feature must be programmed to use this feature. For more information, contact your system administrator.
Procedure: 1 Press the programmed Priority Dispatch button. A tone sounds, and the radio enters Priority Dispatch mode. The radio exits this mode when the Priority Dispatch Time Out Timer expires.
2 Before the Priority Dispatch Time Out Timer expires, press and hold the PTT button to transmit. The display shows the Priority Talkgroup alias.
3 To listen, release the PTT button. The radio exits Priority Dispatch mode, return to its original talkgroup, and displays the home channel alias.

50

MN009203A01-AD Emergency Operation

Chapter 8

Emergency Operation

The Emergency feature is used to indicate a critical situation. An emergency signal overrides any other communication over the selected channel.
Your radio supports the following Emergency modes:
· Emergency Alarm
· Emergency Call
· Emergency Alarm with Emergency Call
Only one Emergency mode can be assigned to the Top (Orange) button.
Your radio is also programmed to operate in one of the following conditions:
Tactical/Non-Revert The radio sends an emergency alarm and/or makes an emergency call on the current channel.
Non-Tactical/Revert for Conventional System The radio reverts to the programmed emergency channel to send an alarm and/or make an emergency call.
Non-Tactical/Revert for Trunking System The radio reverts to the programmed emergency talkgroup (trunking system) or channel (conventional system) to send an alarm and/or make an emergency call.
Fall Alert (Man Down) is an alternate way to activate the Emergency feature.
For more information, contact your system administrator.

8.1
Special Considerations for Emergency Operation
The following scenarios apply during Emergency operation:

Table 11: Emergency Operation Scenarios
Scenario If you press the Top (Orange) button while in a channel that has no Emergency capability. If you change to a channel/mode with no Emergency capability while in Emergency operation.
If you change to a channel/mode with Emergency capability while in Emergency operation. If the radio is out-of-range of the system or the emergency alarm is not acknowledged.

Outcome
A low-pitched tone sounds.
A continuous low-pitched tone sounds until you select a valid Emergency channel/mode or until you disable the Emergency operation. The Emergency Alarm and/or Emergency Call continues on the new channel/mode. A tone sounds and the display shows No acknowledge.

51

MN009203A01-AD Chapter 8 : Emergency Operation
8.2
Sending Emergency Alarms
Procedure: Press the programmed Top (Orange) button.
Your radio shows the following indications: · A positive indicator tone sounds. · The red LED blinks. · The display shows Emergency, and the current zone or channel. When you receive acknowledgement from the dispatcher, your radio shows the following indications: · Four tone sounds. · The alarm stops. · The display shows Ack received. · Your radio exits Emergency Alarm mode.
8.3
Sending Emergency Alarms with Emergency Calls
Procedure: 1 Press the programmed Top (Orange) button.
If successful, your radio shows the following indications: · A positive indicator tone sounds. · The red LED blinks momentarily. · The display shows Emergency, and the current zone or channel. When the radio exits Emergency Alarm and enters the Emergency Call state, your radio shows one of the following indications: · You receive the dispatcher acknowledgment. The display shows Ack received. · You receive no acknowledgment. The display shows No acknowledge. If unsuccessful, a negative indicator tone sounds and your radio rejects to launch emergency mode.
2 To call, press and hold the PTT button. 3 To listen, release the PTT button.
8.4
Exiting Emergency Operation
If an Emergency operation is triggered on your radio, the dispatch console, or radios configured as Supervisor can exit the Emergency operation. Radios configured as Supervisor can cancel emergency mode of other radios. The dispatch console must be programmed to use this feature. For more information, contact your system administrator.
52

MN009203A01-AD Chapter 8 : Emergency Operation

Procedure: · To exit the emergency operation, press and hold the programmed Top (Orange) button. · To exit the emergency operation as supervisor (Trunking only), use one of the following options:

Option
Exiting Emergency operation initiated by the Supervisor

Actions
Perform one of the following actions:
– Press and hold the Top (Orange) button.
– Press and hold the 1-Dot Programmable button. Press the Top (Orange) button.
– Wait for the console to clear the Emergency.

NOTE: Your radio supports the following button combinations: – Radio 1-Dot Programmable button and Top (Orange) button. – Radio 1-Dot Programmable button and accessory Orange button. – Radio Top (Orange) button and accessory 1-Dot Button.

8.5
Remote Emergency
The Remote Emergency feature allows you to remotely launch the emergency feature on a target radio.
You can send the Remote Emergency request to radios from recently transmitted or received calls that are stored.

8.5.1
Sending Remote Emergency to Specific Users
Procedure: 1 Press the programmed Remote Emergency button. 2 Select the required user of the target radio. 3 To send Remote Emergency, press the PTT button.

If the ID of the target radio is valid, your radio displays sending notification and saves the ID as the last Remote Emergency ID. If the ID of the target radio is invalid, your radio displays an invalid ID notification. If your radio is in one of the following states, your radio plays a tone. · Receive-only Channel · Transmit Inhibit · Out of Range · Imbalance Coverage If your radio receives acknowledgment, your radio displays a positive notification. If your radio does not receive acknowledgment from the target radio, your radio displays a negative notification.

53

MN009203A01-AD Chapter 8 : Emergency Operation
8.5.2
Manually Refreshing the Remote Emergency List
Procedure: 1 Press the programmed Remote Emergency button. 2 To refresh the remote emergency list, press Rfsh.
Your radio displays List refreshed followed by the updated remote emergency list..
8.5.3
Receiving Remote Emergency
The remote emergency will only be launched if your radio has the emergency enabled. The receiving radio displays Emergency.
Procedure: To exit the emergency operation, press and hold the programmed Top (Orange) button.
8.6
Emergency Keep-Alive
This feature prevents the radio from being turned off when it is in Emergency mode. If this feature is enabled, you are required to exit Emergency mode before turning off your radio.
8.7
Emergency Beacon
When the radio is in Emergency mode, the Emergency Beacon feature transmits Bluetooth Low Energy (BTLE) signals and other Emergency information to nearby radios. Contact your system administrator for more information.
8.7.1
Sending Emergency Beacons
The following method allows you to transmit the beacon.
Procedure: Press the programmed Top (Orange) button.
8.7.2
Receiving Emergency Beacons
When you receive emergency beacon, the display shows Beacon Received, the transmitting radio ID, or alias.
Procedure: 1 Perform one of the following actions: · To view the beacon list, press Details. · To dismiss the beacon, press Dismiss. NOTE: If there are multiple beacons, the radio displays the recent beacon received.
54

MN009203A01-AD Chapter 8 : Emergency Operation 8.7.3
Viewing Received Emergency Beacon
Procedure: 1 Press the Bcon menu item. NOTE: The received beacons are removed from the list after four minutes.
55

MN009203A01-AD Chapter 9 : Fireground
Chapter 9
Fireground
The portable Fireground Communications System is designed for deployment at an incident scene. It consists of central components that provide on-scene and in building radio coverage, and enhanced personnel accountability and monitoring: · Your APX portable radios · Incident Management Software · Command Terminal · Radio Frequency (RF) Modem (Conventional Only) · Control Channel Radio (Trunking) · Optional Data Radio (Trunking) · Accountability Server (Trunking) · DVRS (Optional) If you have a critical situation, you can press the Emergency button, which activates an alarm on the Incident Management Software at the command terminal. The command terminal receives the following status updates from your radio: · Turning the radio on and off · Automatic response to Polling · Response to Evacuation commands · Pressing the PTT button to make voice transmission · Sending an Emergency Alarm and Call · Entering or exiting a Trunking Talkgroup
9.1
Entering Fireground Zone Channel (Conventional)
Prerequisites: NOTE: If you are entering Fireground Trunking Talkgroup, ensure that the Fireground Trunking Talkgroup is selected.
Procedure: 1 Cycle power your radio. 2 Press the Fireground Zone Channel menu item. 3 Listen for a transmission. 4 To call, press and hold the PTT button. 5 To listen, release the PTT button.
9.2
Responding to Evacuation Indicator
When you receive an Evacuation Indicator, the radio shows the following indications:
56

MN009203A01-AD Chapter 9 : Fireground · A tone sounds. · The display shows the configurable programmed alert text and intelligent lighting. Procedure: 1 To respond, perform one of the following actions: · Press the 3-Dot Programmable button. · If the radio is connected to the Remote Speaker Microphone (RSM), press the 1-Dot button on the RSM. · Press the PTT button. NOTE: The PTT button must be configured in Customer Programming Software (CPS) to enable this function. The radio cancels the indications, a tone sounds, and the radio sends an acknowledgment to the command terminal. 9.3
Sending Evacuation Tone
Procedure: 1 Press and hold the PTT button. 2 Press the Emergency button.
A tone sounds when the Emergency button is released. The tone sounds in all radios within the talkgroup until the PTT button is released.
NOTE: Radio does not transmit evacuation tone if the radio is in secure mode.
57

MN009203A01-AD Chapter 10 : Tactical Public Safety (Conventional Only)
Chapter 10
Tactical Public Safety (Conventional Only)
Tactical Public Safety (TPS) enables the member of a group to identify the start and the end of a transmission by displaying the caller name or ID on the radio display. 10.1
Using TPS Normal Transmission
Procedure: In the TPS Zone Channel, perform one of the following actions: · To talk, press and hold the PTT button. · To listen, release the PTT button. · Receive and listen to the call.
The display shows the caller name or ID. 10.2
Using TPS Emergency Transmission
Procedure: 1 Press the programmed Top (Orange) button. The Emergency Beacon tone sounds. 2 To call, press and hold the PTT button. 3 To listen, release the PTT button. The Emergency Call De-Key Sidetone sounds. After a short pause, the Emergency Beacon tone sounds. 4 To exit or cancel the Emergency mode, press and hold the programmed Top (Orange) button.
58

MN009203A01-AD Man Down (Fall Alert)
Chapter 11
Man Down (Fall Alert)
Man Down (Fall Alert) is a supporting feature of the Emergency operation. The Emergency feature must be programmed for Man Down (Fall Alert) to operate. Your radio activates the Man Down (Fall Alert) feature when it achieves or exceeds a tilt angle threshold or a combination of the angle threshold and radio motion below the motion sensitivity level. The radio must stay in this condition for a programmed period before the Emergency Alarm or Call is activated.
NOTE: Because Man Down (Fall Alert) may be triggered accidentally, consider the following scenarios when using your radio: · If the radio is programmed to a horizontal position only, it must be worn in a vertical position. · If the radio is programmed with the Man Down (Fall Alert) feature, turn off the radio when
charging it with a wall-mounted charger. · When you dismiss Man Down (Fall Alert) and keep the radio horizontal, no emergency will
be sent and no further Man Down (Fall Alert) notification will occur until the device is rotated back to normal (portrait) mode.
11.1
Radio Alerts When Man Down (Fall Alert) is Triggered
When Man Down (Fall Alert) is triggered, your radio plays an alert tone and the display shows Man Down. If the radio is programmed for Surveillance Mode, it inhibits all tones and lights including the Man Down (Fall Alert) tones.
Man Down (Fall Alert) Enhanced
Your radio also supports Man Down (Fall Alert) Enhanced where it plays an alert tone for a preprogrammed period. This tone is louder than the preprogrammed minimum level or the current level of the speaker and it acts as a beacon that helps to find the radio.
NOTE: The radio plays this alert tone even in Surveillance Mode.
When the alert tone is active, changing to another channel with a different setup triggers a different response from the radio: · The alert tone is inhibited when you change to a channel without Emergency feature. · The alert tone is inhibited when you change to a channel with Emergency but no Man Down (Fall
Alert) feature. · The current alert tone is inhibited and is replaced with a different alert tone when you change to a
channel with Emergency feature and a different Man Down (Fall Alert) configuration. · The alert tone continues when you change to a channel with Emergency and similar Man Down
(Fall Alert) configuration.
11.2
Testing Man Down (Fall Alert)
Prerequisites: Ensure that Man Down (Fall Alert) feature is configured in your radio.
59

MN009203A01-AD Chapter 11 : Man Down (Fall Alert) Procedure:
1 Turn on the radio, and place it in a vertical position for at least 5 seconds. 2 Lay the radio down in a horizontal position. Your radio shows the following indications: · Alert tone · The display shows Man-Down. Postrequisites: If Man Down (Fall Alert) is configured but the condition does not trigger the activation of the feature, send the radio to a qualified technician. 11.3
Exiting Man Down (Fall Alert)
Procedure: To exit Man Down (Fall Alert) mode, press Clr.
11.4
Reinitiating Man Down (Fall Alert)
Procedure: To reinitiate Man Down (Fall Alert) after exiting Emergency Operation, perform one of the following actions: · Return the radio to a vertical position. · If motion sensitivity is enabled, shake the radio.
60

MN009203A01-AD Secure Operations
Chapter 12
Secure Operations
Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. By default, the radio automatically enters the encrypted environment without having to manually select or clear the secure transmission.
12.1
Switching Between Secure and Clear Transmission
Procedure: 1 To select Secure Transmission, press the programmed Secure/Clear side button. When you press the PTT button and the selected channel is programmed for clear only operation, your radio shows the following indications. · A negative tone sounds. · The display shows Clear TX only. The radio does not transmit until you set the Secure/Clear side button to clear mode.
2 To select Clear Transmission, press the programmed Secure/Clear side button. When you press the PTT button and the selected channel is programmed for secure only operation, your radio shows the following indications. · A negative tone sounds. · The display shows Secure TX only. The radio does not transmit until you set the Secure/Clear side button to secure mode. NOTE: If the Ignore Secure/Clear Switch When Strapped field is enabled, the radio transmits without displaying any messages in the strapped mode operation. The Secure/ Clear side button is only applicable when the radio is transmitting.
12.2
Encryption
This chapter explains the encryption feature on your radio. NOTE: Contact your system administrator for more information.
12.2.1
Multikey Feature
This feature allows the radio to be equipped with different encryption keys. There are two types of encryption keys:
61

MN009203A01-AD Chapter 12 : Secure Operations
Conventional Multikey The encryption keys are strapped on a one-per-channel basis, through CPS. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups.
Trunked Multikey If both conventional and trunked applications are applied, strap the encryption keys for trunking on a per-talkgroup, or announcement- group basis. Also, a different key can be strapped to other features such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operatorselectable key erasure.
12.2.2
MDC OTAR (Conventional Only)
This feature allows you to view or define the Motorola Data Communications (MDC) Over-theAir Rekeying (OTAR) features. It is applied only when operating in secure encrypted mode. In addition to Rekey Requests, OTAR transmissions include Delayed Acknowledgments, and Power-up Acknowledgments. Some of the selected options require configuration at the Key Management Controller (KMC) site to work properly.
NOTE: This feature must be programmed by a qualified radio technician.
12.2.3
Infinite UKEK Retention
This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all the encryption keys are erased. Without this UKEK key, the radio cannot be rekeyed over the air. The Infinite UKEK Retention settings can be different for each secure profile.
NOTE: This feature must be programmed by a qualified radio technician.
12.2.4
Hear Clear
Hear-Clear is a noise reduction system which consists of Companding and Random FM Noise Canceller. Companding
Reduces the channel noise, such as OTA transmission that is predominantly present in UHF2 and 900 MHz channel with the following features. Compressor Reduces the background noise flow and the speech signal at transmitting radio. Expander Expands the speech while the noise flow remains the same at receiving radio. Random FM Noise Canceller (Flutter Fighter) Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal- to-Noise (S/N) conditions such as in a moving transportation. The fading effects, heard as audio pops and clicks, are canceled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode.
NOTE: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information.
62

MN009203A01-AD Chapter 12 : Secure Operations
12.2.5
Loading Encryption Keys
Procedure: 1 Attach the Key Variable Loader (KVL) to your radio. The display shows Keyloading. All other radio functions are locked, except power down, backlight, and volume. NOTE: If the Multisystem Over-the-Air Rekeying feature is in use, the ASTRO profile name is displayed below Keyloading.
2 Select the required keys and press Load on the KVL. The KVL indicates that key load is successful.
12.2.6
Selecting Encryption Keys
Procedure: 1 Press the Key menu item. 2 Select the required key or enter the key number. 3 To save the new key, press Sel. If the selected key is not allowed, a tone sounds and the display shows Illegal key. If the selected key is erased, a tone sounds and the display shows Key fail.
12.2.7
Selecting Keysets
This feature allows you to select one or a group of encryption keys from the available keys stored in the radio.
Procedure: 1 Press the Kset menu item. 2 Select the required key. 3 To save the new keysets, press Sel.
12.2.8
Erasing Encryption Keys
Procedure: 1 Select Eras. 2 Navigate to the encryption key or use the keypad to enter the key. 3 Select Optn. 4 Select the required option and select Sel. 5 To erase single key from the radio, select Erase single keys?Yes. 6 To erase all keys from the radio, select Erase all key?Yes.
63

MN009203A01-AD Chapter 12 : Secure Operations 12.2.9
Requesting Over-the-Air Rekey
If the Multi-system Over-the-Air Rekeying feature is in use, the rekey request is only for the current selected secure profile. Prerequisites: Ensure that the Unique Key Encryption Key (UKEK) or Unique Shadow Key (USK) is loaded into the radio with the Key Variable Loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. Procedure:
1 Press the Reky menu item. 2 Send the rekey request by pressing the PTT button. 3 To exit the feature and transmit in normal mode, press one of the following buttons:
· PTT button · Home button · Top (Orange) button If the rekey operation fails, a negative tone sounds and the display shows Rekey fail.
NOTE: The rekey operation failure indicates that your radio does not contain the UKEK or USK.
64

MN009203A01-AD Scan
Chapter 13
Scan
This feature allows you to monitor traffic on different channels by scanning a programmed list of channels. Scanning is halted if you initiate a call and resumes when the call has ended.
13.1
Turning Scan On or Off
Procedure: Turn scan on or off by pressing the Scan menu item.
If the scan is enabled, the display shows Scan On and the Scan status icon. If the scan is disabled, the display shows Scan Off.
13.2
Making Dynamic Priority Change (Conventional Scan Only)
While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the default setting. Procedure:
When the radio locks onto the channel designated as the new Priority-Two channel, press the programmed Dynamic Priority button. The radio continues scanning the remaining channels in the list.
13.3
Deleting Nuisance Channel
Procedure: 1 Identify the nuisance channel. 2 Press the Nuis menu item.
The radio continues scanning the remaining channels in the list. NOTE: This feature is not applicable for priority channels, or the designated transmit channel.
13.4
Restoring Nuisance Channels
Procedure: To restore the deleted nuisance channel, perform one of the following actions: · Stop and restart a scan. · Mode change to another channel, and return to the original channel.
65

MN009203A01-AD Chapter 13 : Scan
· Turn off the radio and then turn it on again.
66

MN009203A01-AD Scan Lists

Chapter 14

Scan Lists

Scan lists are created and assigned to individual channels or groups. Your radio scans for voice activity by cycling through the channel or group. The sequence of scan is as specified in the scan list for the current channel or group.
Your radio supports different types of Scan Lists:
· Conventional Scan List
· Talkgroup Scan List
· Trunking Priority Monitor Scan List
Refer to a qualified radio technician for the maximum number of Scan Lists to be programmed in your radio.

14.1
Managing the Scan List

Procedure: 1 Press the SCNL menu item. 2 Manage the scan list by using the following options:

Option Viewing the scan list Adding a channel into the scan list
Removing a channel from the scan list
Recalling the next channel in the scan list

Actions
At the Edit Scan screen, view the scan list by scrolling through the list.
At the Edit Scan screen, press Sel. The currently highlighted channel is added into the scan list.
a At the Edit Scan screen, scroll to the required channel.
b Press Del.
At the Edit Scan screen, press Rcl. The display auto scrolls to the next channel in the scan list.

67

MN009203A01-AD Chapter 15 : Connectivity

Chapter 15

Connectivity
This section explains the management of connections between your radio and a variety of networks and other devices.
15.1
SmartConnect
Before switching broadband connections, your radio compares the relative signal strength of the various broadband connection types to one another, as well as Land Mobile Radio (LMR).
Your radio remains or returns to LMR connection when the other broadband connections fall below the quality threshold. A radio operating on a lower priority broadband connection returns to the higher priority or quality connection while idle on SmartConnect.

Your radio displays the SmartConnect capable icon

on the SmartConnect enabled channel.

When connected to an available network, your radio displays SmartConnect connection icon .
NOTE: This feature must be programmed by a qualified radio technician. For more information, contact your system administrator.
15.2
Wi-Fi
You can connect your radio to a Wi-Fi network for wireless programming. Your service administrator preprograms the Wi-Fi Service Set Identifier (SSID) or network name that your radio can connect to. This feature is enabled by default on your radio.
NOTE: Channel 12 and 13 are enabled for Wi-Fi for all countries except US and Canada.

15.3
Bluetooth®
This feature allows your radio to extend its functionality by connecting to external proprietary Motorola Solutions accessories. Use Motorola Solutions proprietary Mission Critical Wireless (MCW) devices with APX radios during Mission Critical operations. Other Bluetooth devices may or may not meet the mission critical standard.
Your radio supports the following Bluetooth enabled devices or profiles:
· Headset (HSP)
· Dial Up Networking (DUN)
· Personal Area Networking (PAN)
· Serial Port (SPP)
· General Attribute Profile (GATT)

68

MN009203A01-AD Chapter 15 : Connectivity
15.3.1
Turning Bluetooth On or Off
Procedure: 1 Press the BT menu item. 2 Select Status. 3 Perform one of the following actions: · To turn on Bluetooth, press On. · To turn off Bluetooth, press Off.
15.3.2
Searching and Pairing the Bluetooth Device
Prerequisites: Ensure that the Bluetooth on your device is turned on and set to Discoverable in order to enable your radio to detect your device in Bluetooth.
Procedure: 1 Press the BT menu item. 2 Press Search DevicesOn. 3 To pair with an available device, select the required device and press Sel.
The radio pairs to the device.
15.3.3
Turning Bluetooth Audio On or Off
NOTE: Bluetooth audio routing can be configured in the Customer Programming Software (CPS) to route the audio to the radio internal speaker. The audio routes to the radio speaker if the radio Remote Speaker Microphone (RSM) is not connected. For more information, contact your system administrator.
Procedure: 1 Press the BT menu item. 2 Select Bluetooth spkr. 3 Perform one of the following actions: · To turn on Bluetooth audio, press On. · To turn off Bluetooth audio, press Off.
15.3.4
Viewing and Clearing the Bluetooth Enabled Device Information
Procedure: 1 Press the BT menu item. 2 Select Devices and press Sel.
69

MN009203A01-AD Chapter 15 : Connectivity
3 To view the status of devices that are paired or connected, scroll through the list of . If there are no active Bluetooth devices paired or connected, the display shows No devices.
4 To clear a device from the list, select the required device and press ClrYes.
15.4
ASTRO 25 (P25) Programming Over Project 25 (POP25)
Also known as Over-the-Air Programming, this feature allows configuration data and firmware to be upgraded to your radio over-the-air. Full use of the radio is retained during the data transfer without interrupting communication. If the upgrade happens on the ASTRO 25 and ASTRO Conventional systems, the upgrade pauses to give priorities to voice call, and continues after the voice call ended. If the upgrade happens on a Wi-Fi network, the upgrade process runs concurrently with voice calls. Once a configuration upgrade is downloaded to your radio, you can install new changes immediately, or delay changes to be installed on the radio when it is being powered up. Your radio can also be configured to allow you to accept or reject an upgrade.
15.4.1
Responding to Upgrade Notifications
The display shows Upgrade? and a tone sounds every 30 seconds until you accept, delay, or reject the request.
NOTE: Do not remove the power cable or turn off the radio during the firmware upgrade process. If your radio has problems upgrading over-the-air, consult a qualified technician for details.
Procedure: Respond by performing one of the following actions: · To accept the upgrade request, press Acpt. · To delay the upgrade request, press Dlay. · To reject the upgrade request, press Rej.
One of the following scenarios occurs: · If you choose to accept, the display shows Programming Dont power off. The radio resets to
install the upgrade. NOTE: The radio cannot be used while the upgrade is being installed. You must ensure to accept the upgrade at a convenient time.
· If you choose to delay, a configuration data upgrade is installed automatically at the next power up. In the case of a firmware upgrade, the radio prompts Upgrade? again at the next power up.
· If you choose to reject, the display shows Upg Aborted. The radio continues to function with the current configuration until it gets reprogrammed.
70

MN009203A01-AD Location
Chapter 16
Location
The Global Navigation Satellite System (GNSS) in the radio integrates information from the Global Positioning System (GPS) to determine the approximate geographical location of your radio.
NOTE: The Location feature is addressed as Global Positioning System (GPS) across the manual as the naming convention of the buttons and strings remain the same as the legacy feature of GPS. The availability and accuracy of this location information and the calculation duration can vary depending on the environment in which you are using the GPS feature. For example, GPS location fixes are difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. If adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 10 meters from your actual location, but sometimes farther away. Sometimes, the GPS feature cannot complete a location calculation successfully. You will then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, take note of the following guidelines: · For your initial fix, hold the radio in the face position. · Stay in the open as the GPS feature works best when there is nothing between your radio and the open sky.
16.1
Turning Location On or Off
Procedure: 1 Press the Loc menu item. 2 Perform one of the following actions: · To turn on Location, press OptnTurn On GPSSel. · To turn off Location, press OptnTurn Off GPSSel.
16.2
Accessing Location
Procedure: 1 Press the Loc menu item. 2 Press OptnTurn On GPSSel. 3 To check the last successful location fix, select the longitude, time, and date. 4 To access the current location, press Rfsh. 5 To return to the Home screen, press Exit.
If the radio successfully obtains the current location, the display shows the following information: · Current Location
71

MN009203A01-AD Chapter 16 : Location

· UTC (Zulu) Time
· Date
NOTE: If the location signal is present, the location coordinates are automatically updated every five seconds. If the radio fails to obtain the current location, the display shows No service and returns to the previous screen.

16.3
Selecting Location Formats
The Location Format feature allows you to select different display formats of the Global Positioning System (GPS) location. The following GPS location formats are available: · Lat/Long(DD) · Lat/Long(DDM) · Lat/Long(DMS) · UTM/UCS · SLD99 · MGRS
NOTE: When you send your location to another radio, the receiving radio displays the location in its selected format.
Procedure: 1 Press the Loc menu item. 2 Press OptnLoc FormatSel. 3 Select the required location format.
The display shows the location with the selected format. NOTE: If the SLD99 format is selected and the range is invalid, the display shows ­­­­­­­­­­­ on the location. This situation occurs when you use the radio outside of Sri Lanka. To correct this situation, switch the location display format to other GPS options such as DDM, DMS, UTM/UCS, or MGRS.

16.4
Managing Waypoints
Prerequisites: Ensure that your radio displays the current location.
Procedure: 1 Press the Optn menu item. 2 Press WaypointsSel. 3 Manage waypoints by using the following options:

Option Viewing waypoints

Actions
a Scroll to the required waypoint from the list. b Press OptnViewSel.

72

MN009203A01-AD Chapter 16 : Location

Option
Deleting a waypoint Deleting all waypoints

Actions The display shows the following information of the selected waypoint: · Military Grid Reference System (MGRS) or, lati-
tude and longitude location · Time · Date
a Scroll to the required waypoint from the list. b Press OptnDeleteSelYes. The display shows a positive notification.
a Scroll to any waypoint from the list. b Press OptnDelete AllSelYes. The display shows a positive notification.
NOTE: You cannot delete any of the programmed waypoints.

4 Return to the Home Screen by pressing the Home button.

16.5
Location Feature in Emergency Mode
When the Emergency feature is activated, t

References

• Call2Recycle | Leading the Charge For Battery Recycling
• Language selection - Innovation, Science and Economic Development Canada Main Site / Sélection de la langue - Site principal d'Innovation, Sciences et Développement économique Canada

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>