ATandT YJW-06719 15W Qi2 Fast Charge Wireless Charger User Manual
- June 26, 2024
- ATandT
Table of Contents
ATandT YJW-06719 15W Qi2 Fast Charge Wireless Charger
Product Information
Specifications:
- Dimensions: 140 mm x 90 mm
- Print: Double-sided, 299C K100
- Wireless Charger: 15W Qi2 Fast Charge
- Input Voltage: 5VDC/3A, 9VDC/2.22A, 12VDC/1.67A
Product Usage Instructions
Wireless Charging:
Place your Qi-compatible device on the wireless charger to initiate
charging. Ensure the device is properly aligned on the charging pad for
optimal charging efficiency.
FCC Compliance:
Follow FCC guidelines for safe operation of the device to prevent harmful
interference. Make sure the wireless charger is used in accordance with
provided instructions to avoid radio
frequency interference.
FCC RF Exposure Statement:
For safety reasons, maintain a minimum distance of 20cm between the
wireless charger and your body while in use to comply with FCC radiation
exposure limits.
FAQ (Frequently Asked Questions):
-
Q: How do I know if my device is Qi-compatible?
A: Most modern smartphones that support wireless charging are Qi- compatible. You can also refer to your device’s user manual or specifications to confirm its compatibility. -
Q: Can I charge non-Qi devices on this wireless charger?
A: No, this wireless charger is specifically designed for Qi-compatible devices. Using it with non-Qi devices may result in ineffective charging or damage to the device.
Specifications
(charger not included)
- Input:5VDC/3A;9VDC/2.22A;12VDC/1.67A
- Output:SW/7.SW/lOW/lSW
- Charging distance: 5-Gmm
CAUTION:
This wireless charger ONLY works on devices that have built-In wireless. Do
not attempt to disassemble the wireless charging pad as it may damage the
product.
Using your Fast Wireless Charging Pad
- Power up your Wireless Charging Pad using provided USB-C cable. Use Wall Charger (not provided) based on the specification provided.
- Place your Qi-enabled device on the Wireless Charging Pad with the screen facing up.
WARNING: Any metallic/conductive object between device and wireless charging pad will cause an ERROR (i.e. metallic plate)
Charging Indicator Light Status
-
Red flashing light: ERROR, please re-position your device
-
Green light: CHARGING, lights up green, flashes 3 times and goes off (device will remain charging)
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>