BN-LINK BND-60/U132 Easy Set 24 Hour Timer Instruction Manual
- June 5, 2024
- BN-LINK
Table of Contents
BN-LINK BND-60/U132 Easy Set 24 Hour Timer
Please keep this handbook
PROGRAMING & SAFETY INSTRUCTIONS
Rated Voltage: 125VAC, 60Hz
Max.Load: 8A, 1000W
APPLICATIONS
- Lighting
- Humidifiers
- Indoor sprinkers
- Nebulizers
- Aquariums
- Ventilators
WARNING
- For indoor use only
- Follow local electrical codes
- Do not exceed electrical ratings
INITIAL SETUP
-
Remove sticker
Locate the tab at the top right of the sticker and pull to remove sticker from face of screen.
-
Charge the internal battery
If the screen is blank, plug the timer into any outlet for 30 minutes to charge the internal battery.
-
Reset the timer
Press the “RESET” button with the tip of a small non-metallic insulated tool, such as a pencil or toothpick.
-
Unplug and program timer
Charging the battery allows the programming and setup of timer to occur from the comfort of your chair!
SET UP CURRENT TIME
Example: if it is 7:30am, please follow below steps to set time.
- Press “ SET TIME “, the time displayed on the screen will flash.
- Press” + ” or” – ” to adjust the time in 1-minute intervals until the 7:30 00 AM is displayed. You can hold the buttons to fast scrol. Please make sure AM/PM is correct.
- Press “ SET TIME ” to save and quit. If no button is pressed within 60 seconds, the current time will be saved automatically.
SET AN ON AND OFF PROGRAM
- Press the “ PROG ” button to start the program setting, you will see the screen display shown as Fig 04.
Example: if you want to turn on a device every day at 8:05am and turn it off at 9:00pm, please follow below steps.
- Press and hold “+” or”-” button until 8:05 AM displays on the screen.
- Press the “ PROG ” bullon to save and move to the OFF time selling for lhe firs! program.
- Press and hold “ + ” or” – ” button until 9:00 PM displays on the screen.
- Press the “ PROG ” button to save and repeal above steps to set another program if necessary.
Note:
- During lhe program setting stage, you can press “ RCL-DST ” button lo clear the current input and resume it by pressing it again.
- You can revert to clock display screen at any lime during the program setup by pressing “ SET TIME ” button or leave no bullon pressed for 60 seconds.
- The programs take effect in AUTO mode only. Please press and hold “ ON/OFF ” button for 4 seconds lo switch between AUTO and MAN mode.
Attach a DEVICE to the timer
Plug a device inlo the outlet of the timer.
OPERATING MODE
The timer has two different operating modes: AUTO and MANUAL. They are
represented by icons AUTO and MAN.
Press and hold “ ON/OFF ” button for 4 seconds to shift between AUTO and
MANUAL mode. In MANUAL mode, all programs are paused.
Pressing the “ON/OFF” button will allow you to manually turn on or off the
power.
– In AUTO mode, all programs are running. Pressing the “ON/OFF” button will
only temporarily override the power on or off. Timer will continue to run its
next program aulomatically.
DST – DAYLIGHT SAVING TIME FUNCTION
Press “ RCL-DST ” button lo activate or deactivate DST.
Note:
A “+1” icon will appear on the left of the LCD screen when DST is active.
It means manually add 1 hour to open the “Summer Time”, otherwise it returns
to current lime.
TROUBLESHOOTING
Timer does not turn on or off.
a. Make sure AM and PM are correct on the current lime and in the program
sellings.
b. Timer program should be on AUTO setting.
c. Make certain that both ON and OFF time have been specified.
d. If the screen display is not clear or blank, please plug the timer into any
outlet for 30 minutes to charge the internal battery, then press !he “
Reset ” button.
e. If the timer is always ON or always OFF, please check if the program is in
Auto mode.
BN-LINK INC.
12991 Leffingwell Avenue, Santa Fe Springs
Customer Service Aooistance: 1.909.592.1881
E-mail: support@bn-link.com
http://www.bn-link.com
Houro: 9AM 5PM PST, Mon Fri
Designed in California Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>