PROGRESS LIGHTING P400348 Adley Linear Chandelier Ceiling Light Instruction Manual
- June 12, 2024
- PROGRESS LIGHTING
Table of Contents
PROGRESS LIGHTING P400348 Adley Linear Chandelier Ceiling Light
PACKAGE CONTENTS
HARDWARE CONTENTS (not actual size)
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble,operate or install the product.
CAUTION: Read instructions carefully and turn the electricity off at main
circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90°C supply conductors. Consult a qualified
electrician to ensure correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this Fixture,
follow instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
CAUTION: All glass is fragile, use care when handling glass shades and
bulbs.
PREPARATION
- Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damage, do not attempt to assemble, install or operate the product.
- Estimated assembly time: 30 minutes.
- Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder, drill.
CARE AND MAINTENANCE
Shut off main power supply before cleaning the product or changing light bulbs. To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.
ASSEMBLY INSTRUCTIONS
-
Loosely thread the hex nut (DD) onto the nipple (AA) and then install this assembly onto the mounting strap (CC). Next, install this assembly to the outlet box using the mounting screws supplied with the outlet box (not included).
-
In this step, you will adjust the depth of the nipple in relation to the canopy depth.
-
Take the canopy (E) and slip it over the nipple (AA). You will need to adjust the nipple so at least 1/4″ of the threaded portion is exposed through the canopy hole. This is done by adjusting the depth of the nipple (AA) on the mounting strap (CC). When the nipple depth is correctly adjusted, remove the canopy (E) and tighten the hex nut (DD) against the mounting strap (CC).
-
Slip the fixture (A) wires through stem (D). Thread stem (D) into the fixture (A).
-
NOTE: During this step, determine the hanging length of your fixture by removing chain links (FF) and optionally cutting the electrical and ground wire to length.
-
Do NOT cut electrical or ground wires until this overall length is determined. Leave AT LEAST 6 inches MINIMUM of wire past the canopy (E) to allow for easy connections in step 5.
(Chain links can be spread open with 2 pairs of pliers. Twist the split link ends in opposite directions and close by squeezing them back together.) -
Determine the hanging height of the fixture (A) and adjust both chains (FF) at this time. Open chain link at one end of chain (FF) and slip through the chain loop (D). Close the chain links back together with the pliers. Open the quick link (GG) and slip through the chain loop (E) and other end of chain (FF). Close the quick link (GG).
-
Be sure chains are not twisted and align evenly with one another. With the wires exiting the fastened loop (D), weave the wire and ground wire through every third chain link (FF), having them exit up through the canopy loop (E) and out the back of the canopy (E).
-
With the chain links (FF) closed and all the loops (D) fastened securely, have someone help you hold up the fixture by the canopy (E) and visually inspect the chain lengths, making sure fixture hangs evenly.
-
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect the RIBBED fixture wire to the WHITE supply wire from the outlet box; connect the SMOOTH fixture wire to the BLACK supply wire.
-
Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the mounting strap. Push all wire connections into the outlet box.
-
Position and attach the canopy (E) onto the nipple (AA) and use the cylinder nut (EE) to secure the canopy (E) tightly to the ceiling.
-
Attach the glass shade (B) to the fixture (A) using the socket ring (C) to secure it tightly.
-
Thread the lamps (not included) into the fixture sockets. Use 60-watt MAX incandescent medium base, SBCFL or SBLED.
CAUTION: Read the instructions carefully and turn off the power at the
central circuit breaker before beginning the installation.
CAUTION: Risk of fire. Min 90°C supply conductors. Consult a qualified
electrician to ensure a good branch circuit conductor.
WARNING- If there are other regulating mechanisms used with this device,
carefully follow instructions for meeting NEC requirements. If you have any
questions, consult a qualified electrician.
CAUTION – Glass is always fragile; handle component(s) and bulb(s) with
care.
WARRANTY
WARRANTY AND EXCLUSIVE REMEDY
- Delta products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at time of shipment. All warranty claims must be asserted within one year from date of purchase of the subject items; thereafter, warranty claims will not be honored. The customer’s sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at time of shipment. Delta’s sole and maximum liability for a defective product shall never exceed the cost of the subject product.
- EXCEPT FOR SUCH A WARRANlY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANlY OF TITLE), WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILllY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILllY OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS.
- Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract or negligence or strict liability or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers? Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain the customer’s responsibility. The customer is responsible for determining the suitability of our products for the customer’s use or resale, or for incorporating them into objects or for applications that the customer designs, assembles, constructs or manufactures.
We can assist you with questions regarding product information, assembly or missing parts.
- 8oo-447-o573
- 8 am-8 pm (Eastern), Monday-Friday
- customerservice@progresslighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>