PRISMXR P1111 Carina D1 Charging Dock For Quest User Guide

PRISMXR P1111 Carina D1 Charging Dock For Quest

PrismXR Carina D1 Charging Dock for Quest 3

1. Controller Charging Cradles
2. Headset Charging Cradles
3. Quest 3 Charging LED Indicator
4. Left Controller Charging LED Indicator
5. Right Controller Charging LED Indicator
6. LED Button: Tap to turn on/off the three LED indicators
7. Strap Holder
8. AC to DC Adapter
9. USB-C to USB-C Cable
10. Controller Battery Cover
11. Reachargeable Ni-MH AA Battery
12. Magnetic Positioning Component
13. Positioning Bracket

Set Up Magnetic Positioning Component on Quest 3

Note: If you are using an aftermarket facial cover with your Quest 3, please remove it from the Quest 3 first before setting up the Magnetic Positioning Component.

1. Place the positioning bracket on the Quest 3 as shown in the image, ensuring it remains stable and will not move.
2. Remove the release paper from the back of the magnetic positioning component and install it at the designated spot on the positioning bracket. Be careful not to attach it to the wrong orientation.
3. Press and hold the magnetic positioning component for approximately 10 seconds before releasing. Then, remove the positioning bracket.

Set Up Strap Holder (Optional)

Note: Use the provided strap holder to achieve a stable and reliable charge for your Quest 3 with an aftermarket strap.

•  Insert the strap holder into the hole at the bottom rear of the dock.

Set Up Controllers

Note: Normally, the voltage of Ni-MH batteries will drop after being fully charged. After the controllers are fully charged, the battery level displayed on your Quest 3 or in the App will be less than 100%, but will still have enough power to last for more than 10 hours.

1. Press the Eject button to release the battery cover and slide out. Remove AA batteries from controllers.
2. Install the provided rechargeable Ni-MH AA batteries with the silver part facing upward, and then replace the battery cover.

Connecting to Power

•  Use the provided 30W power adapter to connect the dock to the power supply.

Charge Your Quest 3 and Controllers

Note: you can turn the LED indicator on/off by pressing the LED button. \Once the LED indicator is turned off, it will automatically turn on at the next charge.

Place your Quest 3 and controllers on the charging cradles. A beeping sound will confirm a successful connection and indicate that Quest 3 and controllers are ready to be charged.

• Orange: Charging.
• Green: Fully charged.

Charge Your Quest 3 with an Aftermarket Strap

Note:

• The dock is designed to charge only your Quest 3, it will not charge your elite or halo strap with battery.
• Rotate the two arms of Quest 3 downwards until they reach the bottom.
• When using a halo-type strap, if the strap is positioned high above the strap holder, you need to manually press down the strap to ensure it is correctly placed on the strap holder.
• Place the solid white part (not the soft part) of the elite strap or halo strap onto the strap holder. Adjust the position of the strap holder to ensure the fit wheel at the rear of the head strap is located in the hollow position of the holder.
• Place your Quest 3 on the headset charging cradles. A beeping sound will confirm a successful connection and indicate that Quest 3 is ready to be charged.

Care and Cleaning

Note: Do not use any cleaning product that may cause irritation.

• Wipe with a clean, non-abrasive, lint-free cloth.

Specifications

Safety Instruction

Read all the instructions before using the product, refer to the information on the exterior bottom enclosure for electrical and safety information before installing or operating the product.

• Store the product in a cool and dry place.
• Do not store the product in a hot or humid environment.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
• Operating temperature should be between 0°C to 45°C.
• Do not disassemble the product.
• Do not leave or dispose of the product in both extremely low air pressure and extreme heat such as sunshine, fire, or the like.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of \different electrochemical systems separate from each other.
• Be aware the discharged battery may cause fire or smoke, tape the terminals to insulate them.
• Do not subject the product to mechanical shock, crushing, or cutting.
• Do not short-circuit the product or be short-circuited by other metal objects.
• To reduce the risk of injury, close supervision is necessary when this product is used near children or keep the product out of the reach of children.
• Do not put fingers or hands into the product.
• Do not use the product in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.
• Do not use a product that is damaged or modified. It may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Switch off the device when not in use.
• Do not install this equipment in a confined or building-in space such as a bookcase or similar unit, and remain in good ventilation conditions at an open site.
• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
• Attention should be drawn to the environmental aspects of battery disposal.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to\ the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio / TV technician for help.

The following importer is the responsible party.

• Company Name: PRISMXR PTE, LTD
• Address: 60 PAYA LEBAR ROAD #12-03 PAYA LEBAR SQUARE SINGAPORE, 409051

IC Statement

This device complies with Industry Canada license – ICES-003. Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>