HIKVISION T20 4 MP WDR Dome Network IP Camera User Guide
- June 12, 2024
- Hikvision
Table of Contents
Network Camera
Quick Start Guide
User Manual http://enpinfodata.hikvision.com/analysisQR/showQR/a7c6910f
Installation
| 
http://enpinfodata.hikvision.com/analysisQR/showQR/3f36dfd0
---|---
http://enpinfodata.hikvision.com/analysisQR/showQR/d1b6b2db|
http://enpinfodata.hikvision.com/analysisQR/showQR/4631abe6|
Waterproof
Activate and Access Network Camera
http://enpinfodata.hikvision.com/analysisQR/showQR/d983b5d2
| Interface | Description |
|---|---|
| LAN(PoE) | Network interface, PoE supported |
| DC12V, AC24V | Power input interface |
| MicroSD | MicroSD card slot local storage Insert the MicroSD card for |
| RESET | One-key reset button |
| AUDIO IN | Audio input interface |
| AUDIO OUT | Audio output interface |
| ALARM IN | Alarm input interface IN1 and GND1, IN2 and GND2 are two pairs of |
alarm inputs
ALARM OUT| Alarm output interface 1A and 1B, 2A and 2B, 3A and 3B are three
pairs of alarm outputs
RS-485| D+ or D- connect to 485
DC12V, GND/ DC 12V_OUT| Power output interface
BNC| BNC/CVBS interface
| Grounding
Note: The interface varies with the models. Please refer to the product
datasheet for details.
© 2022 Hangzhou Hikvision Digital Technology Co., Ltd. All rights
reserved.
About this Manual
The Manual includes instructions for using and managing the product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other reasons. Please find
the latest version in the company website (https://www.hikvision.com).
Please use this user manual under the guidance of professionals.
Trademarks
and other Hikvision’s trademarks and logos are the properties of
Hikvision in various jurisdictions.
Other trademarks and logos mentioned below are the properties of their
respective owners.
Other trademarks and logos mentioned are the properties of their respective
owners.
: The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI
Logo are trademarks or registered trademarks of HDMI Licensing Administrator,
Inc. in the United States and other countries.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR
PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.
IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF
SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT
(INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH
THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES OR LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY
RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU
ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE
LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT
DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT
LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA
PROTECTION AND OTHER PRIVACY RIGHTS.
YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE
DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR
PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT
RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT
OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC compliance: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
* Wi-Fi device:
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
FCC Conditions
This device complies with part 15 of the FCC RulesOperation is subject to the
following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note: Due to the device size, FCC compliance statement and warnings will
be listed in the manual.
EU Conformity Statement
This product and – if applicable – the supplied accessories too are
marked with “CE” and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the LVD Directive
2014/35/EU, the RoHS Directive 2011/65/EU, Wi-Fi device: the RE Directive
2014/53/EU 2012/19/EU (WEEE directive):
Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this
product to your local supplier upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. Formore information see:
www.recyclethis.info 2006/66/EC (battery
directive):
**** This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for
specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance This device meets the CAN ICES-3
(B)/NMB-3(B) standards requirements.
-
Wi-Fi device:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This equipment should be installed and operated with a minimum distance 20cm
between the radiator and your body.
Safety Instruction
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws, electrical safety
regulations, and fire prevention regulations.
Electricity
In the use of the product, you must be in strict compliance with the
electrical safety regulations of the nation and region. The equipment shall
not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the equipment. Provide a surge
suppressor at the inlet opening of the equipment under special conditions such
as the mountain top, iron tower, and forest. CAUTION: To reduce the risk
of fire, replace only with the same type and rating of fuse.
Battery
Do not ingest battery. Chemical burn hazard! This product contains a
coin/button cell battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death. Keep new
and used batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children. If you
think batteries might have been swallowed or placed inside any part ofthe
body, seek immediate medical attention.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions. Improper replacement
of the battery with an incorrect typemay defeat a safeguard (for example, in
the case of some lithium battery types). Do not dispose of the battery into
fire or a hot oven, or mechanically crush or cut the battery, which may result
in an explosion. Do not leave the battery inan extremely high temperature
surrounding environment, which may result in an explosion orthe leakage of
flammable liquid or gas. Do not subject the battery to extremely low air
pressure,which may result in an explosion or the leakage offlammable liquid or
gas. + identifies the positive terminal(s) of equipment which is used with, or
generates direct current. – identifies the negative terminal(s) of equipment
which is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should be placed on the
equipment. The serial port of the equipment is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned fingers when handling the parts. Wait one-half
hour after switching off before handling parts. This sticker is to indicate
that the marked item can be hot and should not be touched without taking care.
For device with this sticker, this device is intended for installation in a
restricted access location, access can only be gained by service persons or by
users who have been instructed about the reasons for the restrictions applied
to the location and about any precautions that shall be taken.
Installation
Install the equipment according to the instructions in this manual.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV): The power source should meet
limited power source or PS2 requirements according to IEC 60950-1 or IEC
62368-1 standard.
Device powered by AC mains supply voltage: The equipment must be connected to
an earthed mains socket-outlet. An appropriate readily accessible disconnect
device shall be incorporated external to the equipment. An appropriate
overcurrent protective device shall be incorporated external to the equipment,
not exceeding the specification of the building. An all-pole mains switch
shall be incorporated in the electrical installation of the building. Ensure
correct wiring of the terminals for connection to an AC mains supply. The
equipment has been designed, when required, modified for connection to an IT
power distribution system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this product. DO NOT stare
at operating light source. May be harmful to the eyes. Wear appropriate eye
protection or DO NOT turn on the white light when you assemble, install or
maintain the camera.
Transportation
Keep the device in original or similar packaging while transporting it.
System Security
The installer and user are responsible for password and security
configuration.
Maintenance
If the product does not work properly, please contact your dealer or the
nearest service center.
We shall not assume any responsibility for problems caused by unauthorized
repair or maintenance. A few device components (e.g., electrolytic capacitor)
require regular replacement. The average lifespan varies, so periodic checking
is recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside surfaces of the
product cover. Do not use alkaline detergents.
Using Environment
DO NOT place the camera in extremely hot, cold, dusty or damp locations, and
do not expose it to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the
power, unplug the power cable, and contact the service center.
Time Synchronization
Set up device time manually for the first time access if the local time is not
synchronized with that of the network. Visit the device via Web browse/client
software and go to time settings interface.
Reflection
Make sure that no reflective surface is too close to the device lens. The IR
light from the device may reflect back into the lens causing reflection.
See Far Further
UD21665B-F
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>