zencontrol zc-z10 Wireless Microwave Sensor Owner’s Manual
- June 26, 2024
- zencontrol
Table of Contents
zencontrol zc-z10 Wireless Microwave Sensor
Product Information
Specifications
- Supply Voltage: 12 – 24 Vdc
- Supply Current: Not specified
- Control System: Wireless microwave sensor
- Operating Temperature: Not specified
- Material: Not specified
- Mounting: Zhaga standard
- Ingress Protection: Not specified
- Output Voltage (0-10): Not specified
- Output Current (0-10): Not specified
- Classification: Not specified
- Detection Range: Not specified
- Mounting Height: Not specified
- Microwave: Yes
Product Usage Instructions
Mounting Options
The product can be mounted using the following dimensions: 12mm x 36mm. Ensure the mounting is secure and aligned properly.
Power Supply
Connect the product to a power supply with a voltage rating between 12-24 Vdc. Make sure the polarity is correct to avoid damage.
Sensor Activation
The wireless microwave sensor activates based on movement within its detection range. Ensure there are no obstructions blocking the sensor’s field of view.
Output Control
The product provides a 0-10 output signal. Adjust your receiving device or system to interpret and respond to this signal accordingly.
Cleaning and Maintenance
Regularly clean the sensor to prevent dust or debris from affecting its performance. Avoid using harsh chemicals that may damage the product.
FAQ
- Q: What is the detection range of the sensor?
- A: The detection range is not specified in the manual. It is recommended to test the sensor in your specific setting to determine its effective range.
- Q: Can the product be used outdoors?
- A: The Ingress Protection rating for outdoor use is not provided. It is advisable to consult with the manufacturer or supplier before using the product outdoors.
Dimensions
Mounting options: Zhaga male plug
Dimensions: W Ø52 / H 360 mm
Installation
Remove the product from the box and inspect it for any damage. If you believe the product to be damaged or otherwise unsound, do not install the product. Please pack it back into its box and return it to the place of purchase for replacement.
If the product is satisfactory, proceed with the installation:
- Ensure safety warnings are adhered to.
- Install module according to the diagram below.
- Notice: Do not remove the sticker from the outside of the product.
Wiring diagram
Terminal configuration table
- N/C : No connection
- 0-10V: 0-10V / 1-10V control signal
- Vin+: Device positive power supply
- Vin- : Voltage negative power supply
Product range
- Order code: Description
- zc-z10-mw : Wireless microwave sensor, zhaga 0-10 output
- zc-z10: Wireless zhaga 0-10 output
Specifications
-
Supply voltage: 12 – 24 Vdc
-
Supply current: <50mA
-
Control system: IEC62386-104 over Thread
-
Operating temperature: 0 to 40°C
-
Material : PC
-
Mounting: Zhaga port (female)
-
Ingress protection: IP66
-
Output voltage (0-10): 0-10Vdc
-
Output current (0-10): <2mA max
-
Classification: II
-
Detection range: 8 m (mounted at 2.7m)
-
Mounting height: 2 – 8 m
-
Microwave; Microwave 5.8 GHz, 0.2 mW
Safety information
- Before commencing installation turn off and isolate the electrical supply.
- There are no user-serviceable parts, attempting to service any part of the product will void the warranty
- As the installer, it is your responsibility to ensure you comply to all relevant building and safety codes. Refer to applicable standards for the relevant rules.
- When the installation is complete, leave this manual with the building’s owner for future reference.
Notice
Download the control Android app to configure your device
Standalone
zencontrol
Express
Full control
zen control
Commissioining
Information is subject to change without notice, E80E
Last updated 10 / 05 / 24
V 1.3
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>