cudy RE1200 AC1200 Dual Band Wi-Fi Range Extender Installation Guide

: June 25, 2024
: cudy

Table of Contents

cudy RE1200 AC1200 Dual Band Wi-Fi Range Extender
FAQ
Using WPS Button
Using Web browser
LED and Button
FCC STATEMENT
EU Declaration of Conformity
Safety Information
Explanations of the symbols
NEED TECH HELP
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

cudy RE1200 AC1200 Dual Band Wi-Fi Range Extender

FAQ

Frequently Asked Questions

Q1: The login window does not appear when I enter the web address. What should I do?
- If the login window does not appear, please follow these steps:
1. Select Wireless Extender.
2. Click Next.
Q2: What should I do if the LED does not turn on after following the setup steps?
- If the LED does not turn on after 2 minutes, repeat Step 2 of the setup process. If the issue persists, try using Method Two: Using Web Browser. You can also contact our support team at support@cudy.com for assistance.

Using WPS Button

Method One: Using WPS Button

Plug the extender next to your router and wait until the LED turns solid on.
Press the WPS button on your router, and then press the WPS button on the extender within 2 minutes.
The LED will start flashing. When the LED and LED turn solid on, it means the extender is connected to your host WiFi network. If the LED does not turn on after 2 minutes, do Step 2 again. If the issue remains, try Method Two: Using Web Browser.
Connect your device to the extender’s WiFi network. The WiFi name will be “Host WiFi name-EXT2G” or “Host WiFi name-EXT5G” after the configuration and the password is the same as the host WiFi.
- Note: If you are using a Cudy router which supports whole home mesh, when you perform the WPS procedure, the router and extender will mesh together, sharing the same SSID (network name) and password.
Relocate the extender halfway between your router and the WiFi dead zone, find a good place to plug it according to the LED.

Using Web browser

Method Two: Using Web browser

Plug the extender next to your router and wait until the LED turns solid on.
- Connect your computer or smartphone to the extender’s network Cudy—Extender.
Launch a web browser and enter http://cudyre.net/ or http://192.168.10.254/ in the address bar. Use admin for password to log in.
- Note: If the login window does not appear, please refer to FAQ > Q1.
- Select Wireless Extender, then click Next.
Follow the step-by-step configuration and after the setup, the page below will pop up. The LED will take 1-2 minutes to turn solid.
- Note: Please check the information on the screen and confirm that the password is the same as the wifi password of the router. Otherwise, the extender will not be able to connect to the router WiFi.
Connect your device to the extender’s WiFi network. The WiFi name will be “Host WiFi name_EXT2G” or “Host WiFi name_EXT5G” after the configuration and the password is the same as the host WiFi.
Relocate the extender halfway between your router and the WiFi dead zone, find a good place to plug it according to the LED.

Enjoy the internet!

LED and Button

FCC STATEMENT

Regulatory Compliance_RE1200/RE1800

FCC compliance information statement

Product name: AC1200 Wi-Fi Range Extender/AX1800 Wi-Fi 6 Range Extender
Model Number: RE1200/RE1800
Responsible party: Shenzhen Cudy Technology Co., Ltd.
Address: Room A606, Gaoxinqi Industrial Park, Liuxianyi Road, Baoan 67 District, Shenzhen, China
Website: https://www.cudy.com
Tel: +86 755 8600 8993
Email：support@cudy.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

‘To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.’

We, Shenzhen Cudy Technology Co., Ltd., has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference.
this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Operating Frequency (Maximum transmitted power)

2400 MHz – 2483.5 MHz: 20dBm
5150 MHz – 5250 MHz: 23dBm
5250 MHz – 5350 MHz: 20dBm
5470 MHz – 5725 MHz: 20dBm

Frequency band 5150 – 5250 MHz:

Indoor use: Inside buildings only. Installations and use inside road vehicles and train carriages are not permitted. Limited outdoor use: If used outdoors, equipment shall not be attached to a fixed installation or to the external body of road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned aircraft systems (UAS) is limited to within the 5170 – 5250 MHz band.

Frequency band: 5250 – 5350 MHz:

Indoor use: Inside buildings only. Installations and use in road vehicles, trains and aircraft are not permitted. Outdoor use is not permitted.

Frequency band: 5470 – 5725 MHz:

Installations and use in road vehicles, trains and aircraft and use for unmanned aircraft systems (UAS) are not permitted.

EU Declaration of Conformity

Cudy hereby declares that the device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU, directive 2011/65/EU, directive (EU) 2015/863.
The original EU Declaration of Conformity can be found at http://www.cudy.com/ce

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device is used at 20 cm from your body.

National Restrictions

Attention: This device may only be used indoors in all EU member states and EFTA countries, and Northern Ireland.

UKCA Mark

Attention: This device may only be used indoors in Great Britain.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Caution:

The device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
DFS (Dynamic Frequency Selection) products that operate in the bands 5250 – 5350 MHz, 5470 – 5600 MHz, and 5650 – 5725 MHz.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator & your body.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use the device where wireless devices are not allowed.
Make sure the power socket has a good contact with the ground.
Operating Temperature: 0℃ ~ 40℃. (32℉ ~ 104℉)
This product uses radios and other components that emit electromagnetic fields.

Electromagnetic fields and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn off your product and consult your physician for information specific to your medical device.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.